Morris MBH-16314 User manual

INSTRUCTIONS MANUAL
Bathroom heater
Model: MBH-16314
THANK YOU FOR PURCHASING OUR BATHROOM HEATER. BEFORE FIRST USE, PLEASE READ
THE INSTRUCTIONS CAREFULLY, AND KEEP THEM FOR FURTHER REFERENCE.

INTRODUCTION
•Before using your new heater, please carefully read through the following instructions.
•KEEP THIS BOOKLET IN A SAFE PLACE SO THAT YOU MAY CONSULT IT LATER.
•After removing the packaging, make sure that the appliance is in good condition.
•The packaging materials may contain plastic, nails etc., which may be hazardous and therefore should not be left within
the reach of children.
IMPORTANT SAFETY INFORMATION
•Installation MUST be carried out by a qualified electrician.
•Avoid installation behind a door.
•Use only the voltage specified on the rating plate of the heater.
•Do not cover or restrict airflow to the inlet or exhaust grilles in any manner as the appliance may overheat and become
a fire risk (for Fan Heaters).
•Do not cover grilles, block entry or exhaust of airflow by placing appliance against any surface. Keep all objects at least
1 meter from the front and sides of the appliance. With exception of appliances designed for wall-mounting, maintain
a 1-meter gap from the rear of the unit as well.
WARNING: FIRE RISK EXISTS IF THE HEATER IS COVERED BY / OR IF IT IS
POSITIONED CLOSE TO CURTAINS OR OTHER COMBUSTIBLE MATERIALS
•Do not place appliance close to a radiant heat source.
•Do not operate in areas where gasoline, paint or other flammable liquids are used or stored.
•This appliance heats up when in use. To avoid burns, do not let bare skin touch hot surfaces. Switch off and use
handles where provided when moving.
•Do not use the appliance to dry clothes.
•Do not leave the appliance unattended whilst in use.
•Do not insert or allow foreign objects enter any ventilation or exhaust opening, as this may cause an electric shock, fire
or damage to the appliance.
•Do not immerse in liquid or allow liquid to run into the interior of the appliance, as this could create an electrical shock
hazard.
•Do not use this appliance on a wet surface, or where it can fall or be pushed into water.
•Do not reach for an appliance that has fallen into water. Switch off at supply and unplug immediately.
•Do not operate any appliance with a damaged cord, plug or after the appliance malfunction or has been dropped or
damaged in any manner. Return to a qualified electrical person for examination, electrical or mechanical adjustment,
service, or repair before further use.
•Do not operate appliance with wet hands.
•This appliance is intended for household use only and not for commercial or industrial use.
•Use this appliance only as described in this manual. Any other use is not recommended by the manufacturer and may
cause fire, electric shock, or injury.
•A common cause of overheating is deposits of dust or fluff in the appliance. Ensure these deposits are removed
regularly by unplugging the appliance and vacuum-cleaning air vents and grilles, where available.
•Do not use this appliance in a window as rain may cause electric shock.
•Do not use abrasive cleaning products on this appliance. Clean with a damp cloth (not wet) rinsed in hot soapy water
only. Always remove plug from the mains supply before cleaning.
•Do not connect the appliance to the mains source until it has been installed in its final location and adjusted to the
position it will be used in.
•This appliance is not intended for use in bathrooms, laundry or similar locations which may be exposed to water,
moisture or humidity.
•Always operate on a flat horizontal surface.

•Switch off the appliance, then use handles (where provided) to change its position.
•Do not operate with the cord coiled up as this could cause a buildup of heat, which could pose a hazard.
•The use of an extension cord with this appliance is not recommended.
•Do not remove the power plug from the socket by pulling the cord –grip the plug instead.
•Always unplug appliance when not in use.
•Do not allow cord to get close to heated surfaces during operation.
•Do not run cord under carpeting, throw rugs or runners etc. Arrange cord away from areas where it is likely to be
tripped over.
•Do not twist, kink or wrap the cord around the appliance, as this may cause the insulation to weaken and split. Always
ensure that the cord has been fully removed from any cord storage area before use.
•Do not store appliance in a box or closed space until it has cooled down sufficiently.
•This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
•Young children should be supervised to ensure they do not play with the appliance.
•The appliance must not be located immediately below a socket-outlet.
•Do not use this appliance with a programmer, timer or any other device that switches the heater on automatically, since
a fire risk exists if the appliance is covered or positioned incorrectly.
•If the supply cord is damaged, it must be replaced by a qualified electrical person in order to avoid a hazard.
•Do not use this appliance outdoors, or on wet surfaces.Avoid spilling liquid on the appliance.
•In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this appliance must not be supplied
through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by
the utility.
WALL INSTALLATION METHOD:
On the wall, at least 1.8 meters away from the ground, make two holes horizontally with a distance between of about
176mm. Install expansion screws in the holes to keep the nail heads slightly up and project at least 4mm from the wall.
Place the product with the air vent facing downwards, align the screw head with the two holes on the back of the fuselage,
hang it on the screw, and move the product appropriately so that the wall-hanging hole of the product catches the
screw head so as to install it firmly.
After the installation is completed, check the firmness first, and then turn on the power after it is completely stable.

Overview：
Operation:
•Before use, make sure that the towel rack fixing nut is tightened.
•Rotate the towel rack down or up according to your needs.
•Before use, make sure the product is well fixed on the wall.
1. Plug in the power and turn on the main power switch on the back of the product. The product enters the standby state.
The display shows as following image (digital tube shows S):
Display screen
Operate button
Tower rack (Rotatable)
Main button
Towel rack fixing
nut

2. Press the Fkey on the product once, the product works in cold air and the display shows as image A (the digital
tube displays "-"); press twice, the product works at low heat and the display shows as image B; press three times, the
product has high heat work, the display shows as image C; press four times to enter the standby state (the product
needs to delay blowing cold air for 30 seconds).
A B C
3. Press” “ button to set timer(00-12hours). Pressing the button one time increases one hour for timer. After setting time,
the display will show current setting time for 5 seconds, then resume to previous display, meanwhile the light of
”“ will be turned on. Below image is an example of setting 8h:
4. Appointment “ON”: In standby mode, press” “timer button, you can set the appointment turn-on time in 00-12
hours. After complete setting, the display shows the appointment turn-on time and also the light” “ is on. The display
automatically decreases 1 hour for each hour passed. When the appointment power-on time arrived, the product will
automatically turn on. The default setting temperature is 23 ℃during appointment turn-on. Below photos is an example
to set appointment turn-on time to 8 hours:
Note: If not setting the temperature and weekly program, the product will automatically turn-off after 12 hours of
continuous work and enter into standby.

Function operation (ONLY by remote control)
Note: During the operation of the remote control, remote control transmitter must aim at remote control receiving
area of product, avoid remote control ineffective
1. Press” “, the product enters into working status. See below image A
2. Press ” “ button for one time, the product works with low heating and display shows“-- / ”See below
”light on. See
image B. Press again, changes to high heating and display shows“--“at the same time”
below image C:
A B C
3. The timer of remote control operates as same as the timer button on unit body.
4. Set current TIME/DAY (can set both under standby mode & working status):
1.Press ““button for one time, the display shows”12“as default, press “/ ”to set current hour (total
in 24hours); press “ “ again, the display shows minute “ 30“, press” / “to set current minute (00~59
minutes), then press “ “ for third time, the display shows the day“ ”, press “ / “ to set current
day (Monday-Sunday: d1-d7). Then press ‘’ ‘’ to confirm the setting, the display will show previous settings.
For example: Setting to Wednesday, 9:30 AM under 25℃under II heating, pls. refer to the following photos:

Set temperature
During working status, press “ / “,the display shows ” 23 “ as default. Press ” / “ to set
desired temperature (temperature range 10-49℃), press ““to confirm the setting.
For example：The current ambient temperature is 15℃, when set temperature to 25℃, the display shows as below:
If cancel the temperature setting, press the " " key to work in the low or high heating position. At the same
time, the digital tube displays "--", and the "℃" indicator goes out.
Set weekly program (ONLY by remote control)
After complete setting of current TIME/DAY, below is the steps to set weekly program:
1) Press ” “, the product enters into working status.
2) Press “ “, the display shows ”P“, it enters into weekly program setting: See below image A
3) Press”“, the display shows d1~d7, set to working day(Monday-Sunday: d1~d7). Such as set Monday:,
See below image B
4) Press” “, the display shows P1~P6 (for each day, it can be set maximum 6 time periods). Such as setting
P1: See below image C
5) Press ”“,the display shows 00”as default. Press” “ continuously to set the turn-on time. Such as set
the turn-on time 7:00am (Memo: the setting time 00-24 for choice): See below image D
6) Press” “,the display shows the pervious step turn-on time by default. Press” “ continuously to set the
turn-off time. Such as set the shutdown time at 13:00pm (See below image E). Note: turn-off time later than
turn-on time, when turn-on time same as turn-off time, the unit remains in standby mode.
7) Repeat steps 3-6above, and you can set the whole weekly program for each day accordingly.
8) After above setting, press “ “ choose the unit turn-on day of the week, then press “ “ to choose the
turn-on time of the day, then Press ” / “ to set desired temperature (temperature range 10-49℃),press”
to confirm the setting.
9) To cancel the weekly function, press the " " and the light "P" will go off. The weekly program is off. The
product will revert to the previous function working status.
Note:
-After the above setting are completed and P program is working, press ” / “to check the setting time of
each day and time periods.
- The turn-on time periods 00~24hours, cannot set to minutes.
-The “TIME/OFF” cannot be less than “TIME/ON”.
-When the “TIME/ON” is the same as “TIME/OFF”, the time period enter into standby mode.
Note: If main switch off, power cut off, or plug out, it needs reset. You can press to check and set the Time /
Day.

A B C D E
Set open-window detection (ONLY by remote control):
Press“ “，the product enters into working status. Heating for a moment until stable.
Press””by remote control, light “/ ℃“ will on; The temperature displays ”23”by default. Press ”/
“to set desired temperature. During open-window detection mode, once the ambient temperature drops 5-10℃
within 10 minutes, then the product will stop working within 30 minutes and enters into stand by mode. Then
press “ ”to turn on the product.
Press ” “‘’ again to turn off the open-window detection, the light “ ”will go off and the product will
resume to previous working mode.
Below is an example to set 23℃during open-window detection. See below image F:
4)
F G
Maintenance and cleaning
- Warning: Never use detergent, chemical damage plastic parts.
- Warning: Let the appliance cool down completely before handling or cleaning:
•To prevent risk of fire or electrocution inside the appliance.
•Clean the outside wall of the appliance by rubbing it gently with soft, damp cloth, either with or without
soap.
•Regularly clean the air inlet and outlet vents of the fan.
The open-window function is based on the working time that weekly timer is setted. If weekly timer is not working at
a specific period, then open-window function also will not work. Product will stop working when temperature drops
sharply (open-window function works) even if it does not reach the setting temperature. For example, you set 26 ℃
in weekly timer. When the product is at 20 ℃, the open-window function works and then the product will stop
working. See below image G:
Note: you have to set the working time in weekly timer, otherwise it shows '00' which means product will not work.
1)
2)
3)

Model identifier(s): MBH-16314
Item
Symbol
Value
Unit
Item
Unit
Heat output
Type of heat input, for electric storage local space heaters only
(select one)
Nominal heat
output
Pnom 2,0 kW manual heat charge control, with integrated
thermostat
[no]
Minimum heat
output (indicative)
Pmin 1,4kW manual heat charge control with room and/or
outdoor temperature feedback
[no]
Maximum
continuous heat
output
Pmax,c
2,0 kW electronic heat charge control with room and/or
outdoor temperature feedback
[no]
Auxiliary electricity
consumption
fan assisted heat output [no]
At nominal heat
output
elmax 0,0 kW Type of heat output/room temperature control
(select one)
At minimum heat
output
elmin 0,0 kW single stage heat output and no room temperature
control
[no]
In standby mode elSB 0,0 kW Two or more manual stages, no room temperature
control
[no]
with mechanic thermostat room temperature
control
[no]
with electronic room temperature control [yes]
electronic room temperature control plus day
timer
[yes]
electronic room temperature control plus week
timer
[yes]
Other control options (multiple selections possible)
room temperature control, with presence
detection
[no]
room temperature control, with open window
detection
[yes]
with distance control option [no]
with adaptive start control [no]
with working time limitation [yes]
with black bulb sensor [no]
Contact details
Kalliopi Karyda & CO LP
87A, 17th Noemvriou str., PC 55535
Thessaloniki - Greece
T. [phone] | F. [phone]

NOTICE ABOUT RECYCLING
Your product is desiged and manufactured with high quality materials and
components which can be recycled and reused.
This symbol means that electrical and electronic equipment, at their
end-of-life, should be disposed of separately from your household waste.
Please dispose of this equipment at your local community waste collection /
recycling centre.
In the European Union there are separate collection systems for used electrical and
electronic products.
Please help us to conserve the environment we live in!
DECLARATION OF CONFORMITY
Herewith, KALLIOPI KARYDA & CO LP states that this product complies with the
requirements of below directives:
EMC-Directive: 14 / 30 / EU
Low Voltage Directive: 14 / 35 / EU
CE Marking: 93 / 68 / EEC
Erp Directive: 09 / 125 / EC
RoHS Directive 11 / 65 / EU & 15 / 863 / EU
The detailed declaration of conformity can be found at
www.morris.gr
Exclusive importer in Greece:
Kalliopi Karyda & CO LP
87A, 17th Noemvriou str, P.C. 55534
Thessaloniki –Greece
T: [phone] | F: [phone]
www.morris.gr