Morris MPH-20041S User manual

MPH-20041S
for WiFi connection

NOTE: User interface is indicative and may change due to continuous
improvement of user's experience
REGISTRATION TO THE APPLICATION
1. Press button 'Register'
to create a new account
2. Press 'Agree' for
Privacy Policy, to continue.

3. Enter your email or your
mobile telephone number to
get verification code and
press 'Get verification
code'.
Enter verification code and
create a password before
you press to confirm
'Done'.
Note: the verification code
will be sent to you either at
your mobile or at your
email, depending on which
registration way you chose
in the beginning.

NETWORK SETTINGS
You can be connected to the App using one of these ways:
- Add manually, or
- Search by device
Before you begin network setting progress, make sure the device is as closer
as it can be to the Wifi router.
Introduction to connection mode
Wifi function is on automatically right after the device is switched on. If this
does not happen, press for 3 seconds button 1 (photo 1).
Manual connection through 'Add Manually' mode
Before you begin the connection procedure, make sure the Wifi function of the
device is activated and that the indicative light blinks rapidly.
If not, press button 1 for 3 seconds while checking that your mobile is connected to
Wifi network.
Connect to the App and press
button + to add your device.
Photo 1

- Press up left 'Add Manually'.
- In vertical menu on the left, select
'Small Home Appliances'.
- Chose the device's type Heater.
Note: the photo is for reference
only, the category and / or the
device's type may appear in
different place on your screen.
Make sure the WiFi indicator
rapidly blinks.
If not, press button 1 (photo 1) for 3
seconds.

Select your Home Network, enter
your password and press 'Confirm'.
All settings will be transfered to
your device.
Please wait until the device has
been succesfully connected. If
connection fails, try again.
If connection fails again, please
check 'Troubleshooting' for further
assistance.
Once the connection is done, the
device will appear on your screen.
Press 'Done' to complete the
procedure.

Automatic connection through 'Search for Device' mode
Before you begin the connection procedure, make sure the Wifi function of
the device is activated and that the indicative light rapidly blinks.
Press up right 'Search for Device'.
Make sure the Access Location is
activated and press WiFi
activation button 'Enable Wi-Fi' to
be connected.
Make sure the WiFi indicator light
rapidly blinks, then press
'Configuring Wi-Fi' choice to start
the scanning procedure.

Your home network should appear on
the screen now. Your mobile device
must be connected at this same Wifi
network. Enter your password and
press 'Confirm' button.
Important Notice: Only 2.4GHz
networks are supported.
4. At this point, "searching
device" procedure begins
5. If searching procedure fails, please
try again. If it fails again, please
check 'Troubleshooting' for further
assistance.
Once searching procedure is
completed, the device will appear
on your screen as 'available'. Press
'Next' to complete the connection
procedure.

Device control environment
Settings screen
Timer settings
- Choose the time you wish to activate / de-
activate the device.
- Choose to repeat the settings for specific
days.
- Choose timer's action: Activate or de-
activate.
Press to enter to timer settings.
1. Press buttons '+ / -' to increase / decrease temperature
settings of the device.
2. On your screen you can see the current temperature.
3. Press button to activate / de-activate the device.
4. Press 'Function' button to set speed of the device (Levels 1, 2,
3).
5. Press 'ECO' button to set ECO function. This switches off the
display.
6. Press 'Settings' button to control other functions (timer,
Child-lock etc.).
Press bar to activate / de-activate Child-lock mode.
Press bar to activate 'countdown' to turn off heater.

Troubleshooting
* Check if the device is activated and in Stand-By mode. If not, activate it and
press button 1 (image1) for 3 seconds. When WiFi function is activated, the
indicative light rapidly blinks.
*Make sure the WiFi password has been typed correctly (uppercase
and / or lowercase letters considered as different).
* Make sure your mobile is properly connected to WiFi Network.
*Make sure the network you use is 2.4GHz (WiFi 5GHz network is not
supported) and that your signal is strong enough.
* Check your WiFi router settings. The encryption must be WPA2-PSK and
protocol must be AES.
*If you cannot be connected with fast connection guide, follow the instructions
for connection and try with manual search.

EXCLUSIVE DISTRIBUTOR
KALLIOPI KARYDA & CO LP
87A, 17th November str.
55535 Pylea, Thessaloniki, Greece
tel. [phone]
fax [phone]
www.morris.gr Version 1.0 / Aug. 2020