Morris MOR-TBH-1FT User manual

TUBULAR HEATER
INSTRUCTION MANUAL
Tubular Heater: MOR-TBH-1FT/ MOR-TBH-2FT/
MOR-TBH-3FT/ MOR-TBH-4FT
YOU SHOULD READ THE MANUAL CAREFULLY BEFORE
USING, AND KEEP THE MANUAL FOR FUTURE
REFERENCE.
DISPOSAL
This symbol indicates that this product must not be placed in general household
waste. It should be sent to a separate recycling facility for recovery, check Local
Authorities for details.
By responsible recycling and separating this product from other household waste it
will help protect the environment and human health, as the volume of waste sent to
incinerators
or land-fills will be reduced and natural resources
conserved.
Please Note: During the first use the heater may emit a small amount of vapour which is perfectly
normal. The reason for this is the heating wire element is coated with some lubricant oil during
the production process. This will stop after approx. 5 minutes after the first use and is
not a safety concern.
Read all the instructions prior to use.
1. Safety Regulations
•The tubular heater is not suitable for use outdoors in damp weather.
•Do not submerge into water.
•Place in a safe place away from flammable objects.
•Do not place flammable liquids or gasses near the heater.
•Do not place the heater directly below the socket outlet.
•Do not let the power cord over hang or touch the tube.
•Keep out of reach of children and animals – product gets hot to
touch.
•This is not a toy.
•Switch off appliance when not in use.
•Do not hold the tubular heater by the cord.
•If using an extension cord it must be as short as possible and fully
extended.
•Check heater regularly if using with a timer or any other device that
switches the tubular heater on or off automatically.
•This leaflet should be retained for instructions on use.
2.Cleaning
Ensure product is unplugged from the mains. Ensure product is
completely cold.

Wipe with a damp cloth, then finish by drying with a soft cloth. DO NOT
use abrasive cleaning powders, clothes or metal polishes on any part
of the tubular heater as this will cause damage.
3.Thermal Cut-out
The appliance is fitted with a thermal cut-out. Once the tubular heater
has cooled down it will re-set itself automatically. It will then switch on
and off until the reason for overheating has been removed.
4.Operation
Notice: DO NOT SWITCH POWER ON TO THE HEATER UNTIL IT IS
SECURELY MOUNTED.
Step 1. Install the bracket as the picture shows.
Step 2. Fix the tubular heater on the wall or on the floor like the
following picture shows.
5.Tubular Heater Notice:
• The heater is fitted with a safety device which will switch off the
heater in case of accidental overheating.
• To reset, turn the heater off at the switch for a few minutes to allow
the unit to cool down.
• Make sure that any causes of overheating, such as obstructions, are
removed and plug the appliance in again.
•Turn the switch off when it is summer or nobody at home or no need to
keep heating, it is energy saving and safer.
6.Tubular heater Specifications
7.Warranty
This product is guaranteed under warranty and covers defects in material or
workmanship from 1 year of date of purchase. The original bill of purchase
(with purchase date) must be submitted.
The warranty will not apply in cases of: Misuse: by non-compliance of the
instructions, normal wear and tear, incorrect use, e.g. overloading,
non-approved accessories, force or damaged caused by external forces, if the
plug has been tampered with or removed, partially or completely dismantled
product, or interference by non-qualified persons.
Model No.
Power
Electrical Supply
IP Rating
Product Length
(mm)
Product Size (mm)
MOR-TBH-1FT
60W
220-240V ,50 Hz
IP55
300mm
310*98*85
MOR-TBH-2FT
120W
220-240V ,50 Hz
IP55
609mm
610*98*85
MOR-TBH-3FT
180W
220-240V ,50 Hz
IP55
900mm
910*98*85
MOR-TBH-4FT
240W
220-240V ,50 Hz
IP55
1200mm
1200*98*85