Morris MHR-20044S User manual

MHR-20044S
for WiFi connection

NOTE: The environment that appears is indicative and may change to
some upgrade as part of the ongoing improvement of this experience
REGISTRATION TO THE APPLICATION
1. Press button 'Register'
to create a new account
2. Press 'Agree' for
Privacy Policy, to continue.

3. Enter your email or your
mobile telephone number to
get verification code and
press 'Get verification Code'.
When you receive
verification code, type it to
the spaces and create a
password before you press
to confirm 'Done'.
Note: the verification code
will be sent to you either at
your mobile or at your
email, depending on which
registration way you chose
in the beginning.

NETWORK SETTINGS
You can be connected to the App using one of these ways:
- Add manually, or
- Search by device
Before you begin network setting progress, make sure the device is as closer
as it can be to the Wifi router.
Introduction to connection mode
The device connects automatically to Wifi right after switch on. If this does not
happen, press for 3 seconds buttons b, d, e (image 1).
Manual connection through 'Add Manualy' mode
Before you begin the connection procedure, make sure the Wifi connection of the
device is activated and that the indicative light flashes.
If not, press button 1 for 1 second while checking that your mobile is connected to Wifi
network.
Enter the App and press button + to
add your device.

- Press up left 'Add Manually'.
- In vertical menu on the left, select
'Small Home Appliances'.
- Chose the device's type Heater.
Note 2: the photo is just indicative, it
is possible the category and / or the
device's type may appear in another
place of your screen.
Make sure the WiFi indicator light
flashes.
If not, press buttons b, d, e for 3
seconds (image 1).
Note 1: In case you have activated
Bluetooth, the device will
automatically appear on your screen
as 'Device to be added' .

Select your Home Network, enter
your password and press 'Confirm'.
All settings will be transfered to
your device.
Please wait till the connection with
the device is successfully added.
If connection fails, try again.
If connection fails again, please
check 'Troubleshooting' chapter
for further assistance.
Once the connection is done, the
device will appear on your screen.
Press button 'Done' to complete
procedure.

Automatic connection through 'Search for Device' mode
Before you begin the connection procedure, make sure the Wifi connection of
the device is activated and that the indicative light flashes.
Press up right 'Search for Device'.
Make sure the Access Location is
activated and press WiFi
activation button 'Enable Wi-Fi' to
be connected.
Make sure the WiFi indicator light
flashes to the device, then press to
start scanning 'Configuring Wi-Fi'
choice.

Your home network should appear on
the screen now. At this same network
you must have connected your mobile
also. Enter your password and press
'Confirm' button.
Important Notice: Only 2.4GHz
networks are supported.
4. At this point, begins searching
the device.
5. If searching procedure fails, please
try again.
If it fails again, please check
'Troubleshooting' chapter for
further assistance.
Once searching procedure is
done, the device will appear on
your screen as 'available'.
Press button 'Next' to complete
connection procedure.

Device control environment
Settings screen
Timer settings
- Chose the time you wish to activate / de-
activate the device.
- Chose to repeat the settings for specific
days.
- Chose timer's action: Activate or de-
activate.
Press to go to timer's settings.
1. Press buttons '+ / -' to increase / reduce temperature settings
of the device.
2. On your screen you can see the recent temperature.
3. Press button to activate / de-activate the device.
4. Press 'Function' button to set speed of the device (ECO,
Levels 1, 2, 3).
5. Press 'Settings' button to control other functions
(Timer, Child-lock etc.).
Press bar to activate Timer - to switch on unit.
Press bar to de-activate Timer - to switch off unit.
Press bar to activate / de-activate Child-lock mode.
Press bar to activate / de-activate Sound.

Troubleshooting
* Check if the device is activated and in Stand-By mode. If not, activate it and
press buttons b, d, e (image1) for about 5 seconds. When WiFi function is
activated, the indicative light flashes rapidly.
*Make sure the WiFi password has ben typed correctly (capitals and / or
lowercase letters considered as different).
* Make sure your telephone is properly connected to WiFi Network.
*Make sure the network you use is 2.4GHz (WiFi 5GHz network is not
supported) and that your signal is strong enough.
* Check your WiFi router settings. The encryption must be WPA2-PSK and
protocol must be AES.
*If you cannot be connected with fast connection guide, follow the instructions
for connection and try with manual search.

EXCLUSIVE DISTRIBUTOR
KALLIOPI KARYDA & CO LP
87A, 17th November str.
55535 Pylea, Thessaloniki, Greece
tel. [phone]
fax [phone]
www.morris.gr Version 1.0 / Aug. 2020