Motorola Sliver II User manual

MOTOROLA
SLIVER II
EN

EN Check it out 1
Check it out
here’s what you can do
Enjoy crystal clear calls and rich sound with your
MOTOROLA SLIVER II Bluetooth® headset. So
small, it’s barely noticeable. So packed with
features, like wide-band audio and noise
cancellation, it’s impossible to ignore.
Go ahead, check it out:
At a glance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Charge it . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Connect & go. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Basics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Want more?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Safety, Regulatory & Legal . . . . . . . . . . . . . . . . . . . . . 20
Caution: Before using your product, please
read the safety, regulatory and legal
information at the back of this guide.

2At a glance EN
At a glance
the important bits, quick and easy
Status
Light
Volume
Buttons
Call
Button
Charge
(Micro
USB)
Turn On & Off
Turn the
earpiece
left or right
to turn on.
Return earpiece to closed
(storage) position to turn off.
Charge & Store
Wear

EN Charge it 3
Charge it
let’s get you up and running
Headset Status Light
Green - more than 4 hours talk-time
Yellow - between 2-3 hours talk-time
Red - less than 1 hour talk-time
Charge
Headset
Case Status Light
Green - fully charged (two full headset charges)
Yellow - 30-70% charged (one full headset charge)
Red - less than 30% charged
(less than one headset charge)
Charge
Case
Note: You can
close the case lid
when charging.
Charge
(Micro USB)

4Charge it EN
You can charge the headset in several ways:
•Place the headset in the case, and plug the
charger into the case’s micro USB port. The
headset charges first, then the case.
•Charge the case first, then place the headset
in the case when you need to charge it.
•Plug the charger directly into the headset’s
micro USB port.
Notes:
•Fully charge the headset before you use it.
•The case or headset status light flashes when
it is charging. When not charging, the case or
headset status light shows a steady color that
indicates the battery charge level.
•When the charger is not attached, the case
status light turns off after 30 seconds.
Caution: Your battery is designed to last the life
of your device. It should only be removed by a

EN Charge it 5
recycling facility. Any attempt to remove or
replace your battery will damage the device, void
your warranty, and could cause injury.
Tip: To save battery power, turn off the headset
when you’re not using it.

6Connect & go EN
Connect & go
let’s get you connected
2
Turn on your headset and follow the
voice prompts.
4
When the device and headset connect,
you’ll hear “pairingcomplete”.
3
Go to the Bluetooth menu on your device
to pair & connect with the headset. Enter
passcode 0000 if prompted.
1
Turn on Bluetooth on your device.

EN Basics 7
Basics
standard features, advanced quality
Calls
To…
answer a call Press the Call button.
reject a call Press and hold the Volume Up
or Volume Down button until
you hear a tone.
make a voice
dial call
Press the Call button to
activate voice recognition.
mute or
unmute a
call
Press and hold the Volume Up
and Volume Down buttons
until you hear “mute on” or
“mute off”.
end a call Press the Call button.

8Basics EN
Notes:
•Some features are phone/network dependent.
•Using a mobile device or accessory while
driving may cause distraction and may be
illegal. Always obey the laws and drive safely.
change call
volume
Press the Volume Up or
Volume Down button. To
quickly change volume, press
and hold the Volume Up or
Volume Down button.
answer a
second
incoming
call
Press the Call button.
reject a
second call
Press and hold the Volume Up
or Volume Down button until
you hear a tone.
To…

EN Basics 9
Headset status light
Light shows… your headset is…
two blue blinks,
pause, repeat
powered on &
searching for a device
steady blue for three
seconds, then off
connected to a device
flashing red charging, battery at
low power
flashing yellow charging, battery at
medium power
flashing green charging, battery at
high power
steady green connected to charger,
battery fully charged

10 Basics EN
Charge Case Status Light
music
To stream music from your device to the
headset, start and control music playback from
the device.
Light shows… Your case is…
flashing red being charged, battery
at low power
flashing yellow being charged, battery
at medium power
flashing green being charged, battery
at high power
steady red less than 30%
charged
steady yellow 30% to 70% charged
steady green fully charged

EN Basics 11
Music pauses when you make or receive a call,
and resumes playing when the call ends.
Note: This feature is phone dependent.
Clean & dry
To get the most from your headset, keep it clean
and dry.
•High humidity or perspiration can make the
ear fitting feel slippery. Wipe the ear fitting
with a soft cloth to remove dirt and moisture.
Note: Be very careful when wiping near the
speaker.
•Check for and remove any debris that may
be blocking the small microphone ports near
the Call button.

12 Advanced EN
Advanced
more clever stuff
Second device
Do you use two phones? Or maybe a phone and
a tablet? Connect with both of them.
1Pair each device with the headset as normal
(see “Connect & go” on page 6). You don’t have
to turn off the first device to pair with the
second one, as long as it’s done within five
minutes of turning on the headset.
2Once paired, to connect with both devices
simply turn them on. You’ll hear
“device <number> connected” as each
device connects with your headset.

EN Advanced 13
Notes:
• Two phones connected, not on a call: Press
the Call button to activate voice recognition on
the first phone. Double-press it to activate
voice recognition on the second phone.
• Two phones connected, single held call:
Press the Call button to return to the call on
the first phone. Double-press it to return to
the call on the second phone.
Caller ID
Note: This feature is phone/network dependent.
If the phone supports the Phonebook Access
profile, you’ll hear “call from <caller’s name>”
when the contact info is stored on your phone.
Note: This feature doesn’t work when you’re on
a call and you receive a second incoming call.

14 Advanced EN
Battery readout
When you’re not in a call, press the Volume Up
and Volume Down buttons to hear how much
battery talk-time is left on your headset.
Settings
Press and hold the Call button while turning on
the headset, then follow the voice prompts to
turn these features on/off:
• Restore Factory Settings: Reset default
settings on your headset.
Caution: This feature erases all pairing
information stored on the headset.
•VoiceInterface: Turn voice prompts on/off.
• Caller ID Alert: Hear caller ID for incoming
calls.
• Multipoint: Connect your headset to two
devices.

EN Advanced 15
•Wide-band: Use HD Audio Plus for increased
clarity and richer sound.
• Voice Answer: Speak to answer incoming
calls.

16 Want more? EN
Want more?
we’re here to help
Troubleshooting
A few frequently asked questions—with
answers, of course. Find more at
www.motorola.com/support.
• My headset will not enter pairing mode
Make sure that any devices previously paired
with the headset are turned off, then turn the
headset off and on (close and reopen
earpiece). You’ll hear “Sliver II is ready to
pair”.
• My phone doesn't find my headset when
searching
Press and hold the Call button, and turn the
headset off and on (close and reopen
earpiece). Follow the voice prompts to reset

EN Want more? 17
the headset. You’ll hear “Sliver II is ready to
pair”.
• My headset will not pair with my phone
Press and hold the Call button, and turn the
headset off and on (close and reopen
earpiece). Follow the voice prompts to reset
the headset. You’ll hear “Sliver II is ready to
pair”.
• My headset connected before, but now it's
not working
Make sure your phone is on and the phone’s
Bluetooth® feature is turned on. If the
Bluetooth feature was turned off or was
turned on only temporarily, you may need to
restart the Bluetooth feature and pair your
phone and headset again. See “Second
device” on page 12.

18 Want more? EN
Connect with Motorola
•Answers:Guides, online help, and more at
www.motorola.com/support.
• Support: Visit www.motorola.com/support or
contact the Motorola Customer Support
Center at: 1-800-331-6456 (United States),
1-888-390-6456 (TTY/TDD United States for
hearing impaired), or 1-800-461-4575
(Canada).
•Bluetooth®:If you have questions or need
assistance, contact us at 1-877-MOTOBLU, or
visit www.motorola.com/bluetoothsupport or
www.motorola com/bluetoothconnect.
• Accessories: Find more accessories at
www.motorola.com/products.

EN Want more? 19
•Social:The latest news, tips & tricks, videos
and so much more—join us on:
Yo u Tu b e ™ www.youtube.com/motorola
Facebook® www.facebook.com/motorola
Tw i t t e r www.twitter.com/motomobile
Google+™ www.google.com/+