Motorola M-CORE MMC2001 Series User manual

M•CORE™
MMC2001
Reference Manual
Revision 1.1
Motorola reserves the right to make changes without further notice to any products herein to improve reliability,
function or design. Motorola does not assume any liability arising out of the application or use of any product or circuit
described herein; neither does it convey any license under its patent rights nor the rights of others. Motorola products
are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body,
or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola
product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola
products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers,
employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and
reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or
manufacture of the part. The Motorola name and logotype are trademarks of Motorola, Inc.
The M•CORE name and logotype and the OnCE name are trademarks of Motorola, Inc.
© Motorola, Inc. 1998
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

MMC2001 MOTOROLA
REFERENCE MANUAL iii
Conventions
This document uses the following notational conventions:
mnemonics Instruction mnemonics are shown in lowercase bold
0x0F Hexadecimal numbers
0b0011 Binary numbers
Nomenclature
Logic level one is the voltage that corresponds to a Boolean true (1) state.
Logic level zero is the voltage that corresponds to a Boolean false (0) state.
To set a bit or bits means to establish logic level one on the bit or bits.
To clear a bit or bits means to establish logic level zero on the bit or bits.
LSB means least significant bit or bits. MSB means most significant bit or bits. Refer-
ences to low and high bytes are spelled out.
A signal is asserted when it is in its active or true state, regardless of whether that
state is represented by a high or low voltage. A signal is negated when it is in its inac-
tive or false state.
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

MOTOROLA MMC2001
iv REFERENCE MANUAL
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

MMC2001 MOTOROLA
REFERENCE MANUAL v
TABLE OF CONTENTS
Paragraph Title Page
SECTION 1
INTRODUCTION
SECTION 2
INTEGER CPU
2.1 M•CORE Overview ..........................................................................................2-1
2.2 Features...........................................................................................................2-2
2.3 Microarchitecture Summary.............................................................................2-2
2.4 Programming Model.........................................................................................2-3
2.5 Data Format Summary.....................................................................................2-5
2.6 Operand Addressing Capabilities.....................................................................2-6
2.7 Instruction Set Overview..................................................................................2-6
2.8 M•CORE Bus Interface....................................................................................2-8
2.8.1 Bus Characteristics .......................................................................................2-8
2.8.2 Bus Signals ...................................................................................................2-9
2.8.3 Signal Descriptions......................................................................................2-10
2.8.4 Bus Operation .............................................................................................2-11
2.8.5 Processor Instruction/Data Transfers..........................................................2-13
2.8.6 Bus Exception Cycles..................................................................................2-14
SECTION 3
SYSTEM MEMORY MAP
3.1 Overview..........................................................................................................3-1
3.2 Peripheral Module Address Allocation.............................................................3-1
3.3 Peripheral Module Interface Operation............................................................3-2
3.4 Peripheral Module Address Assignment..........................................................3-2
SECTION 4
SIGNAL DESCRIPTIONS
4.1 Overview..........................................................................................................4-1
4.2 Signal Index .....................................................................................................4-2
4.3 Bus Signals......................................................................................................4-4
4.3.1 Address Bus (ADDR[19:0]) ...........................................................................4-4
4.3.2 Data Bus (DATA[15:0])..................................................................................4-4
4.3.3 Output Enable (OE).......................................................................................4-4
4.3.4 Read/Write Enable (R/W)..............................................................................4-4
4.3.5 Enable Byte 1 (EB1)......................................................................................4-4
4.3.6 Enable Byte 0 (EB0)......................................................................................4-4
4.3.7 Chip Selects (CS3, CS[2:0])..........................................................................4-4
4.3.8 Internal ROM Disable (MOD) ........................................................................4-4
4.4 Exception Control Signals................................................................................4-4
4.4.1 Reset (RSTIN)...............................................................................................4-4
4.4.2 Low Voltage Reset (LVRSTIN)......................................................................4-5
4.4.3 Reset Out (RSTOUT)....................................................................................4-5
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

MOTOROLA MMC2001
vi REFERENCE MANUAL
TABLE OF CONTENTS
Paragraph Title Page
4.5 Clock Signals ...................................................................................................4-5
4.5.1 Crystal Oscillator (XOSC, EXOSC)...............................................................4-5
4.5.2 Clock Input (CLKIN) ......................................................................................4-5
4.5.3 Clock Output (CLKOUT)................................................................................4-5
4.6 Debug and Emulation Support Signals............................................................4-5
4.6.1 Test Clock (TCK)...........................................................................................4-5
4.6.2 Test Data Input (TDI).....................................................................................4-5
4.6.3 Test Data Output (TDO)................................................................................4-6
4.6.4 Test Mode Select (TMS) ...............................................................................4-6
4.6.5 Test Reset (TRST)........................................................................................4-6
4.6.6 Debug Event (DE).........................................................................................4-6
4.6.7 Factory Test Mode (TEST)............................................................................4-6
4.7 External Interrupts/GPIO Signals.....................................................................4-6
4.7.1 External Interrupts 7 – 0 (INT[7:0])................................................................4-6
4.8 Keypad Signals................................................................................................4-7
4.8.1 Column Strobes (COL[7:0])...........................................................................4-7
4.8.2 Row Senses (ROW[7:0])...............................................................................4-7
4.9 UART Module Signals......................................................................................4-7
4.9.1 Receive Data (RxD0, RxD1) .........................................................................4-7
4.9.2 Transmit Data (TxD0, TxD1).........................................................................4-7
4.9.3 Clear to Send (CTS0)....................................................................................4-7
4.9.4 Request to Send (RTS0)...............................................................................4-8
4.10 Serial Peripheral Interface Module Signals......................................................4-8
4.10.1 SPI Data Master Out/Slave In (SPI_MOSI)...................................................4-8
4.10.2 SPI Data Master In/Slave Out (SPI_MISO)...................................................4-8
4.10.3 SPI Serial Clock (SPI_CLK)..........................................................................4-8
4.10.4 SPI Enable (SPI _EN)...................................................................................4-8
4.10.5 SPI General-Purpose Output (SPI _GP).......................................................4-8
4.11 Pulse Width Modulator Signals........................................................................4-8
4.11.1 PWM[5:0].......................................................................................................4-8
4.12 Power and Ground Pins...................................................................................4-9
4.12.1 Positive Supply (VDD)....................................................................................4-9
4.12.2 Ground (GND)...............................................................................................4-9
4.12.3 Standby Battery Power (VBATT).....................................................................4-9
4.12.4 Standby Power Filter (VSTBY)........................................................................4-9
SECTION 5
ROM MODULE
5.1 Overview..........................................................................................................5-1
5.2 Functional Description......................................................................................5-1
5.3 Applications......................................................................................................5-2
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

MMC2001 MOTOROLA
REFERENCE MANUAL vii
TABLE OF CONTENTS
Paragraph Title Page
SECTION 6
STATIC RAM MODULE
6.1 Overview..........................................................................................................6-1
6.2 Functional Description......................................................................................6-1
SECTION 7
EXTERNAL INTERFACE MODULE
7.1 Overview..........................................................................................................7-1
7.2 Signals .............................................................................................................7-1
7.2.1 Address Bus..................................................................................................7-1
7.2.2 Data Bus........................................................................................................7-2
7.2.3 Read/Write ....................................................................................................7-2
7.2.4 Control Signals..............................................................................................7-2
7.2.5 Boot Mode.....................................................................................................7-2
7.2.6 Chip Select Outputs ......................................................................................7-2
7.3 Chip-Select Address Range.............................................................................7-3
7.4 EIM Interface Example.....................................................................................7-3
7.5 EIM Functionality..............................................................................................7-4
7.5.1 Configurable Bus Sizing................................................................................7-4
7.5.2 External Boot ROM Control...........................................................................7-6
7.5.3 Programmable Output Generation................................................................7-6
7.5.4 Bus Watchdog Operation..............................................................................7-6
7.5.5 Error Conditions ............................................................................................7-6
7.5.6 Show Cycles..................................................................................................7-7
7.6 EIM Programming Model .................................................................................7-7
7.6.1 Chip-Select Control Registers.......................................................................7-7
7.7 EIM Configuration Register............................................................................7-11
7.8 External Bus Timing Diagrams.......................................................................7-13
SECTION 8
CLOCK MODULE AND LOW-POWER MODES
8.1 Overview..........................................................................................................8-1
8.2 Low-Power Modes ...........................................................................................8-4
8.2.1 CPU Core Low-Power Modes.......................................................................8-4
8.2.2 Peripheral Behavior in Low-Power Modes....................................................8-5
8.2.3 General Low-Power Features .......................................................................8-7
SECTION 9
TIMER/RESET MODULE
9.1 Overview..........................................................................................................9-1
9.2 Timer/Reset Programming Model....................................................................9-1
9.3 Reset Operation...............................................................................................9-2
9.3.1 Reset Pins.....................................................................................................9-2
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

MOTOROLA MMC2001
viii REFERENCE MANUAL
TABLE OF CONTENTS
Paragraph Title Page
9.3.2 Reset Sources...............................................................................................9-2
9.3.3 Reset Sequence............................................................................................9-3
9.3.4 Reset Source/Chip Configuration Register (RSCR)......................................9-3
9.4 Time-of-Day Timer...........................................................................................9-4
9.4.1 TOD Operation..............................................................................................9-5
9.4.2 TOD in Low-Power Modes............................................................................9-5
9.4.3 Time-of-Day Control/Status Register (TODCSR)..........................................9-5
9.4.4 TOD Seconds Register (TODSR) .................................................................9-6
9.4.5 TOD Fraction Register (TODFR)...................................................................9-6
9.4.6 TOD Seconds Alarm Register (TODSAR).....................................................9-7
9.4.7 TOD Fraction Alarm Register (TODFAR)......................................................9-7
9.5 Watchdog Timer...............................................................................................9-8
9.5.1 Watchdog Timing Specifications...................................................................9-9
9.5.2 Watchdog Timer after Reset .........................................................................9-9
9.5.3 Watchdog Timer Service Operation..............................................................9-9
9.5.4 Watchdog Timer in Wait Mode......................................................................9-9
9.5.5 Watchdog Timer in Doze Mode.....................................................................9-9
9.5.6 Watchdog Timer in Stop Mode......................................................................9-9
9.5.7 Watchdog Timer in Debug Mode.................................................................9-10
9.5.8 Watchdog Timer Programming Model.........................................................9-10
9.6 Interval Timer (PIT)........................................................................................9-11
9.6.1 PIT Operation..............................................................................................9-12
9.6.2 PIT as a “Set-and-Forget” Timer.................................................................9-12
9.6.3 PIT as a “Free-Running” Timer ...................................................................9-13
9.6.4 Interval Timer Registers ..............................................................................9-13
9.6.5 PIT Control/Status Register (ITCSR) ..........................................................9-14
9.6.6 PIT Data Register (ITDR)............................................................................9-15
9.6.7 PIT Alternate Data Register (ITADR) ..........................................................9-16
9.6.8 PIT in Low-Power Modes............................................................................9-16
9.6.9 PIT in Debug Mode .....................................................................................9-16
SECTION 10
INTERRUPT CONTROLLER
10.1 Overview........................................................................................................10-1
10.2 Interrupt Controller Programming Model........................................................10-2
10.2.1 Interrupt Source Register (INTSRC) ...........................................................10-2
10.2.2 Normal Interrupt Enable Register (NIER)....................................................10-3
10.2.3 Fast Interrupt Enable Register (FIER).........................................................10-3
10.2.4 Normal Interrupt Pending Register (NIPND)...............................................10-4
10.2.5 Fast Interrupt Pending Register (FIPND)....................................................10-5
10.2.6 Interrupt Request Input Assignments..........................................................10-5
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

MMC2001 MOTOROLA
REFERENCE MANUAL ix
TABLE OF CONTENTS
Paragraph Title Page
SECTION 11
UNIVERSAL ASYNCHRONOUS RECEIVER/TRANSMITTER MODULE
11.1 Overview........................................................................................................11-1
11.2 UART Signals.................................................................................................11-2
11.2.1 RTS — Request to Send (UART0)..............................................................11-2
11.2.2 CTS — Clear to Send (UART0) ..................................................................11-2
11.2.3 TXD — UART Transmit...............................................................................11-3
11.2.4 RXD — UART Receive ...............................................................................11-3
11.3 Sub-Block Description....................................................................................11-3
11.3.1 Transmitter..................................................................................................11-3
11.3.2 Receiver......................................................................................................11-3
11.3.3 Infrared Interface.........................................................................................11-4
11.3.4 16x Bit Clock Generator..............................................................................11-4
11.3.5 General UART Definitions...........................................................................11-4
11.4 UART Programming Model............................................................................11-5
11.4.1 UART Receive Register (URX)...................................................................11-7
11.4.2 UART Transmitter Register (UTX) ..............................................................11-8
11.4.3 UART Control Register 1 (UCR1) ...............................................................11-9
11.4.4 UART Control Register 2 (UCR2) .............................................................11-11
11.4.5 UART BRG Register (UBRGR).................................................................11-13
11.4.6 UART Status Register (USR)...................................................................11-14
11.4.7 UART Test Register (UTS)........................................................................11-15
11.5 GPIO Pins and Registers.............................................................................11-16
11.5.1 UART Port Control Register (UPCR) ........................................................11-16
11.5.2 UART Data Direction Register (UDDR).....................................................11-16
11.5.3 UART Port Data Register (UPDR) ............................................................11-17
11.6 Data Sampling Technique on the Receiver..................................................11-17
11.7 UART Operation in Low-Power System Modes...........................................11-23
11.8 UART Operation in System Debug Mode....................................................11-24
SECTION 12
INTERVAL MODE SERIAL PERIPHERAL INTERFACE
12.1 Overview........................................................................................................12-1
12.2 Operation .......................................................................................................12-1
12.2.1 Manual (Master) Mode................................................................................12-2
12.2.2 Interval (Master) Mode................................................................................12-3
12.2.3 Slave Mode .................................................................................................12-3
12.3 Signal Descriptions ........................................................................................12-3
12.3.1 SPI_MISO (Master In, Slave Out) ...............................................................12-3
12.3.2 SPI_MOSI (Master Out, Slave In)...............................................................12-4
12.3.3 SPI_EN........................................................................................................12-4
12.3.4 SPI_CLK......................................................................................................12-4
12.3.5 SPI_GP .......................................................................................................12-4
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

MOTOROLA MMC2001
x REFERENCE MANUAL
TABLE OF CONTENTS
Paragraph Title Page
12.4 ISPI Programming Model...............................................................................12-4
12.4.1 ISPI Data Register.......................................................................................12-5
12.4.2 ISPI Control Register...................................................................................12-5
12.4.3 ISPI Interval Control Register......................................................................12-8
12.4.4 ISPI Status Register....................................................................................12-8
12.5 ISPI Programming Examples.........................................................................12-9
12.5.1 Manual Mode Example................................................................................12-9
12.5.2 Slave Mode Example ................................................................................12-10
12.5.3 Interval Model Example.............................................................................12-10
12.6 ISPI Operation in Low-Power System Modes..............................................12-11
12.7 ISPI Operation in System Debug Mode.......................................................12-11
SECTION 13
EXTERNAL INTERRUPTS/GPIO (EDGE PORT)
13.1 Overview........................................................................................................13-1
13.2 Interrupt/General-Purpose I/O Pin Descriptions (INT[0:7]) ............................13-1
13.3 Edge Port Programming Model......................................................................13-2
13.3.1 Edge Port Pin Assignment Register (EPPAR) ............................................13-2
13.3.2 Edge Port Data Direction Register (EPDDR)..............................................13-3
13.3.3 Edge Port Data Register (EPDR)................................................................13-3
13.3.4 Edge Port Flag Register (EPFR).................................................................13-4
SECTION 14
KEYPAD PORT
14.1 Overview........................................................................................................14-1
14.2 KPP Pin Description.......................................................................................14-2
14.2.1 Input Pins ....................................................................................................14-2
14.2.2 Output Pins..................................................................................................14-2
14.3 KPP Programming Model...............................................................................14-2
14.3.1 Keypad Control Register (KPCR)................................................................14-2
14.3.2 Keypad Status Register (KPSR) .................................................................14-3
14.3.3 Keypad Data Direction Register (KDDR) ....................................................14-5
14.3.4 Keypad Data Register (KPDR)....................................................................14-5
14.4 Keypad Operation..........................................................................................14-6
14.4.1 Keypad Matrix Construction........................................................................14-6
14.4.2 Keypad Port Configuration..........................................................................14-6
14.4.3 Keypad Matrix Scanning .............................................................................14-6
14.4.4 Keypad Standby.........................................................................................14-7
14.4.5 Glitch Suppression on Keypad Inputs.........................................................14-7
14.4.6 Multiple Key Closures..................................................................................14-8
14.4.7 Typical Keypad Configuration and Scanning Sequence.............................14-9
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

MMC2001 MOTOROLA
REFERENCE MANUAL xi
TABLE OF CONTENTS
Paragraph Title Page
SECTION 15
PULSE WIDTH MODULATOR
15.1 Overview........................................................................................................15-1
15.2 PWM Programming Model.............................................................................15-2
15.2.1 PWM Control Register.................................................................................15-4
15.2.2 PWM Period Register..................................................................................15-6
15.2.3 PWM Width Register...................................................................................15-7
15.2.4 PWM Counter Register ...............................................................................15-7
15.3 PWM Operating Range..................................................................................15-8
15.4 PWM Operation in Low-Power System Modes..............................................15-8
SECTION 16
OnCE™ DEBUG MODULE
16.1 Overview........................................................................................................16-1
16.2 Operation .......................................................................................................16-1
16.3 OnCE Pins .....................................................................................................16-3
16.3.1 Debug Serial Input (TDI) .............................................................................16-3
16.3.2 Debug Serial Clock (TCK)...........................................................................16-3
16.3.3 Debug Serial Output (TDO).........................................................................16-3
16.3.4 Debug Mode Select (TMS)..........................................................................16-3
16.3.5 Test Reset (TRST)......................................................................................16-4
16.3.6 Debug Event (DE).......................................................................................16-4
16.4 OnCE Controller and Serial Interface.............................................................16-4
16.5 OnCE Interface Signals..................................................................................16-5
16.5.1 Internal Debug Request Input (IDR)............................................................16-5
16.5.2 CPU Debug Request (DBGRQ)..................................................................16-5
16.5.3 CPU Debug Acknowledge (DBGACK)........................................................16-5
16.5.4 CPU Breakpoint Request (BRKRQ)............................................................16-5
16.5.5 CPU Address, Attributes (ADDR, ATTR) ....................................................16-5
16.5.6 CPU Status (PSTAT)...................................................................................16-5
16.5.7 OnCE Debug Output (DEBUG)...................................................................16-6
16.6 OnCE Controller Registers.............................................................................16-6
16.6.1 OnCE Command Register (OCMR)............................................................16-6
16.6.2 OnCE Control Register (OCR) ....................................................................16-8
16.6.3 OnCE Status Register (OSR)....................................................................16-11
16.7 OnCE Decoder (ODEC)...............................................................................16-12
16.8 Memory Breakpoint Logic ............................................................................16-12
16.8.1 Memory Address Latch (MAL)...................................................................16-13
16.8.2 Breakpoint Address Base Registers (BABA, BABB).................................16-14
16.8.3 Breakpoint Address Mask Registers (BAMA, BAMB) ...............................16-14
16.8.4 Breakpoint Address Comparators.............................................................16-14
16.8.5 Memory Breakpoint Counters (MBCA, MBCB) .........................................16-14
16.9 OnCE Trace Logic........................................................................................16-14
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

MOTOROLA MMC2001
xii REFERENCE MANUAL
TABLE OF CONTENTS
Paragraph Title Page
16.9.1 Trace Counter (OTC) ................................................................................16-15
16.9.2 Trace Operation ........................................................................................16-15
16.10 Methods of Entering Debug Mode ...............................................................16-16
16.10.1 Debug Request During RESET.................................................................16-16
16.10.2 Debug Request During Normal Activity.....................................................16-16
16.10.3 Debug Request During Stop, Doze, or Wait Mode....................................16-16
16.10.4 Software Request During Normal Activity .................................................16-16
16.10.5 Enabling OnCE Trace Mode .....................................................................16-16
16.10.6 Enabling OnCE Memory Breakpoints........................................................16-17
16.11 Pipeline Information and Write-Back Bus Register......................................16-17
16.11.1 Program Counter Register (PC)................................................................16-18
16.11.2 Instruction Register (IR) ............................................................................16-18
16.11.3 Control State Register (CTL).....................................................................16-18
16.11.4 Write-Back Bus Register (WBBR).............................................................16-19
16.11.5 Processor Status Register (PSR)..............................................................16-19
16.12 Instruction Address FIFO Buffer (PC FIFO).................................................16-20
16.12.1 Reserved Test Control Registers (Reserved, MEM_BIST, FTCR, LSRL) 16-21
16.13 Serial Protocol Description...........................................................................16-21
16.13.1 OnCE Commands.....................................................................................16-21
16.14 Target Site Debug System Requirements....................................................16-21
16.15 Interface Connector For JTAG/OnCE Serial Port ........................................16-22
APPENDIX A
ELECTRICAL CHARACTERISTICS
A.1 Maximum Ratings ............................................................................................A-1
A.2 DC Electrical Specifications.............................................................................A-1
A.3 Clock Input Specifications................................................................................A-2
A.4 AC Electrical Specifications .............................................................................A-2
A.4.1 Reset, MOD Timing Specifications..............................................................A-2
A.4.2 External Interrupt Timing Specifications......................................................A-3
A.4.3 EIM Timing Specifications ...........................................................................A-4
A.4.4 ISPI Timing Specifications...........................................................................A-6
A.4.5 OnCE Timing Specifications........................................................................A-9
APPENDIX B
PACKAGING AND PIN ASSIGNMENTS
B.1 Overview..........................................................................................................B-1
APPENDIX C
PROGRAMMING REFERENCE
C.1 Peripheral Module Address Assignment..........................................................C-1
C.2 Interrupt Controller Programming Model..........................................................C-2
C.2.1 Interrupt Source Register (INTSRC)............................................................C-2
C.2.2 Normal Interrupt Enable Register (NIER) ....................................................C-2
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

MMC2001 MOTOROLA
REFERENCE MANUAL xiii
TABLE OF CONTENTS
Paragraph Title Page
C.2.3 Fast Interrupt Enable Register (FIER).........................................................C-3
C.2.4 Normal Interrupt Pending Register (NIPND)................................................C-4
C.2.5 Fast Interrupt Pending Register (FIPND).....................................................C-4
C.3 Timer/Reset Programming Model....................................................................C-5
C.3.1 Reset Source/Chip Configuration Register (RSCR)....................................C-5
C.3.2 Time-of-Day Control/Status Register (TODCSR)........................................C-7
C.3.3 TOD Seconds Register (TODSR)................................................................C-7
C.3.4 TOD Fraction Register (TODFR).................................................................C-8
C.3.5 TOD Seconds Alarm Register (TODSAR)...................................................C-8
C.3.6 TOD Fraction Alarm Register (TODFAR)....................................................C-9
C.3.7 Watchdog Control Register (WCR)..............................................................C-9
C.3.8 Watchdog Service Register (WSR) ...........................................................C-10
C.3.9 PIT Control/Status Register (ITCSR).........................................................C-11
C.3.10 PIT Data Register (ITDR) ..........................................................................C-12
C.3.11 PIT Alternate Data Register (ITADR).........................................................C-13
C.4 KPP Programming Model...............................................................................C-13
C.4.1 Keypad Control Register (KPCR)..............................................................C-14
C.4.2 Keypad Status Register (KPSR)................................................................C-14
C.4.3 Keypad Data Direction Register (KDDR)...................................................C-15
C.4.4 Keypad Data Register (KPDR)..................................................................C-15
C.5 EIM Programming Model ...............................................................................C-16
C.5.1 Chip-Select Control Registers ...................................................................C-16
C.5.2 EIM Configuration Register........................................................................C-20
C.6 PWM Module..................................................................................................C-22
C.6.1 PWM Control Register...............................................................................C-23
C.6.2 PWM Period Register................................................................................C-25
C.6.3 PWM Width Register .................................................................................C-26
C.6.4 PWM Counter Register..............................................................................C-27
C.7 Edge Port Programming Model......................................................................C-27
C.7.1 Edge Port Pin Assignment Register (EPPAR)...........................................C-27
C.7.2 Edge Port Data Direction Register (EPDDR).............................................C-28
C.7.3 Edge Port Data Register (EPDR) ..............................................................C-29
C.7.4 Edge Port Flag Register (EPFR) ...............................................................C-29
C.8 ISPI Programming Model...............................................................................C-30
C.8.1 ISPI Send/Receive Data Register..............................................................C-30
C.8.2 ISPI Control Register.................................................................................C-31
C.8.3 ISPI Interval Control Register....................................................................C-33
C.8.4 ISPI Status Register ..................................................................................C-34
C.9 UART Programming Model............................................................................C-34
C.9.1 UART Receive Register (URX)..................................................................C-36
C.9.2 UART Transmit Register (UTX).................................................................C-37
C.9.3 UART Control Register 1 (UCR1)..............................................................C-38
C.9.4 UART Control Register 2 (UCR2)..............................................................C-40
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

MOTOROLA MMC2001
xiv REFERENCE MANUAL
TABLE OF CONTENTS
Paragraph Title Page
C.9.5 UART BRG Register (UBRGR) .................................................................C-42
C.9.6 UART Status Register (USR) ...................................................................C-42
C.9.7 UART Test Register (UTSR) .....................................................................C-43
C.9.8 UART Port Control Register (UPCR).........................................................C-44
C.9.9 UART Data Direction Register (UDDR).....................................................C-45
C.9.10 UART Port Data Register (UPDR).............................................................C-45
C.10 OnCE Registers.............................................................................................C-46
C.10.1 OnCE Command Register (OCMR)...........................................................C-46
C.10.2 OnCE Control Register (OCR)...................................................................C-47
C.10.3 OnCE Status Register (OSR)....................................................................C-50
C.10.4 Memory Address Latch (MAL)...................................................................C-51
C.10.5 Breakpoint Address Base Registers (BABA, BABB) .................................C-51
C.10.6 Breakpoint Address Mask Registers (BAMA, BAMB)................................C-51
C.10.7 Breakpoint Address Comparators..............................................................C-51
C.10.8 Memory Breakpoint Counters (MBCA, MBCB)..........................................C-51
C.10.9 Program Counter Register (PC) ................................................................C-51
C.10.10 Instruction Register (IR).............................................................................C-52
C.10.11 Control State Register (CTL).....................................................................C-52
C.10.12 Write-Back Bus Register (WBBR) .............................................................C-53
C.10.13 Processor Status Register (PSR)..............................................................C-53
C.10.14 Reserved Test Control Registers (Reserved, MEM_BIST, FTCR, LSRL).C-53
INDEX
RECORD OF CHANGES
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

MMC2001 MOTOROLA
REFERENCE MANUAL xv
LIST OF ILLUSTRATIONS
Paragraph Title Page
1-1 MMC2001 Block Diagram................................................................................1-2
2-1 Programming Model.........................................................................................2-4
2-2 Data Organization in Memory ..........................................................................2-5
2-3 Data Organization in Registers........................................................................2-5
2-4 Signal Relationships to Clocks.........................................................................2-9
2-5 M•CORE Bus Signals ....................................................................................2-10
2-6 External Multiplexer Connections...................................................................2-13
4-1 Functional Signal Groups.................................................................................4-1
7-1 EIM Block Diagram ..........................................................................................7-1
7-2 EIM Interface to Memory and Peripherals........................................................7-4
7-3 CS0 Control Register.......................................................................................7-7
7-4 CS1, CS2, CS3 Control Registers ...................................................................7-8
7-5 EIM Configuration Register............................................................................7-11
7-6 Read Memory Access (CSA = 0, WSC = 1)...................................................7-14
7-7 Write Memory Access (CSA = 0, WSC = 1, WWS = 0) .................................7-15
7-8 Word Read Access from Halfword Width Memory.........................................7-16
7-9 Word Write Access to Halfword Width Memory.............................................7-17
7-10 Write after Read Memory Access (CSA = 0, WSC = 2, EDC = 0) .................7-18
7-11 Write after Read Memory Access (CSA = 0, WSC = 1, EDC = 1) .................7-19
7-12 Peripheral Read Access (CSA = 1, WSC = 5)...............................................7-20
7-13 Peripheral Write Access (CSA = 1, WSC = 5) ...............................................7-21
7-14 Read and Write Fast Memory Access (CSA = 0, WSC = 0, WWS = 0).........7-22
8-1 MMC2001 Clock Module..................................................................................8-3
9-1 Reset Functional Block Diagram......................................................................9-2
9-2 Reset Source Register.....................................................................................9-3
9-3 TOD Block Diagram.........................................................................................9-4
9-4 TOD Control/Status Register ...........................................................................9-5
9-5 TOD Seconds Register....................................................................................9-6
9-6 TOD Fraction Register.....................................................................................9-7
9-7 TOD Seconds Alarm Register..........................................................................9-7
9-8 TOD Fraction Alarm Register...........................................................................9-8
9-9 Watchdog Timer Block Diagram ......................................................................9-8
9-10 Watchdog Control Register............................................................................9-10
9-11 Watchdog Service Register............................................................................9-11
9-12 PIT Block Diagram.........................................................................................9-12
9-13 Starting a Count from an Off State.................................................................9-12
9-14 Counter Reloading from the Modulus Latch...................................................9-13
9-15 Counter in Free-Running Mode......................................................................9-13
9-16 PIT Control and Status Register ....................................................................9-14
9-17 PIT Data Register...........................................................................................9-15
9-18 PIT Alternate Data Register...........................................................................9-16
10-1 Interrupt Source Register...............................................................................10-2
10-2 Normal Interrupt Enable Register...................................................................10-3
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

MOTOROLA MMC2001
xvi REFERENCE MANUAL
LIST OF ILLUSTRATIONS
Paragraph Title Page
10-3 Fast Interrupt Enable Register.......................................................................10-3
10-4 Normal Interrupt Pending Register.................................................................10-4
10-5 Fast Interrupt Pending Register.....................................................................10-5
11-1 UART Channel Block Diagram.......................................................................11-2
11-2 UART Receive Register.................................................................................11-7
11-3 UART Transmitter Register............................................................................11-9
11-4 UART Control Register 1 ...............................................................................11-9
11-5 UART Control Register 2 .............................................................................11-12
11-6 UART BRG Register....................................................................................11-13
11-7 UART Status Register..................................................................................11-14
11-8 UART Test Register.....................................................................................11-15
11-9 UART Port Control Register.........................................................................11-16
11-10 UART Data Direction Register.....................................................................11-16
11-11 UART Port Data Register.............................................................................11-17
11-12 Start Bit — Ideal Case..................................................................................11-19
11-13 Start Bit — Noise Case One ........................................................................11-20
11-14 Start Bit — Noise Case Two ........................................................................11-21
11-15 Start Bit — Noise Case Three......................................................................11-22
11-16 Start Bit — Noise Case Four........................................................................11-23
12-1 ISPI Channel Block Diagram..........................................................................12-1
12-2 Timing Diagram of ISPI 8-Bit Operation.........................................................12-2
12-3 ISPI Data Register .........................................................................................12-5
12-4 ISPI Control Register .....................................................................................12-5
12-5 ISPI Interval Control Register.........................................................................12-8
12-6 ISPI Status Register.......................................................................................12-8
13-1 External Interrupt/GPIO Block Diagram.........................................................13-1
13-2 Edge Port Pin Assignment Register...............................................................13-2
13-3 Edge Port Data Direction Register.................................................................13-3
13-4 Edge Port Data Register................................................................................13-3
13-5 Edge Port Flag Register.................................................................................13-4
14-1 KPP Block Diagram........................................................................................14-1
14-2 Keypad Control Register................................................................................14-3
14-3 Keypad Status Register .................................................................................14-4
14-4 Keypad Data Direction Register.....................................................................14-5
14-5 Keypad Data Register....................................................................................14-5
14-6 Keypad Synchronizer Functional Diagram.....................................................14-8
14-7 Decoding Wrong Three Key Presses.............................................................14-9
15-1 PWM Block Diagram......................................................................................15-1
15-2 PWM Generating Audio .................................................................................15-1
15-3 PWM Prescaler..............................................................................................15-2
15-4 PWM Control Registers..................................................................................15-4
15-5 PWM Period Registers...................................................................................15-6
15-6 PWM Width Registers....................................................................................15-7
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

MMC2001 MOTOROLA
REFERENCE MANUAL xvii
LIST OF ILLUSTRATIONS
Paragraph Title Page
15-7 PWM Count Registers....................................................................................15-7
16-1 OnCE Block Diagram.....................................................................................16-1
16-2 OnCE Controller.............................................................................................16-2
16-3 OnCE Controller and Serial Interface.............................................................16-4
16-4 OnCE Command Register .............................................................................16-7
16-5 OnCE Control Register ..................................................................................16-8
16-6 OnCE Status Register..................................................................................16-11
16-7 OnCE Memory Breakpoint Logic..................................................................16-13
16-8 OnCE Trace Logic Block Diagram...............................................................16-15
16-9 CPU Scan Chain Register (CPUSCR).........................................................16-17
16-10 Control State Register..................................................................................16-18
16-11 OnCE PC FIFO............................................................................................16-20
16-12 Recommended Connector Interface to JTAG/OnCE Port............................16-22
A-1 CLKIN Timing (for Square Wave Input) ...........................................................A-2
A-2 Reset Timing....................................................................................................A-3
A-3 MOD Timing.....................................................................................................A-3
A-4 External Interrupt Timing..................................................................................A-4
A-5 EIM Read/Write Timing....................................................................................A-5
A-6 SPI Slave Timing (PHA = 0).............................................................................A-7
A-7 SPI Slave Timing (PHA = 1).............................................................................A-7
A-8 SPI Manual/Interval Mode Timing (PHA = 0)...................................................A-8
A-9 SPI Manual/Interval Mode Timing (PHA = 1)...................................................A-8
A-10 Test Clock Input Timing ...................................................................................A-9
A-11 TRST Timing....................................................................................................A-9
A-12 Test Access Port Timing................................................................................A-10
B-1 144-Lead Plastic Thin Quad Flat Pack Pin Assignment...................................B-1
C-1 Interrupt Source Register.................................................................................C-2
C-2 Normal Interrupt Enable Register.....................................................................C-3
C-3 Fast Interrupt Enable Register.........................................................................C-3
C-4 Normal Interrupt Pending Register...................................................................C-4
C-5 Fast Interrupt Pending Register.......................................................................C-4
C-6 Reset Source Register.....................................................................................C-6
C-7 TOD Control/Status Register ...........................................................................C-7
C-8 TOD Seconds Register....................................................................................C-8
C-9 TOD Fraction Register.....................................................................................C-8
C-10 TOD Seconds Alarm Register..........................................................................C-9
C-11 TOD Fraction Alarm Register...........................................................................C-9
C-12 Watchdog Control Register............................................................................C-10
C-13 Watchdog Service Register............................................................................C-11
C-14 PIT Control and Status Register ....................................................................C-11
C-15 PIT Data Register...........................................................................................C-13
C-16 PIT Alternate Data Register...........................................................................C-13
C-17 Keypad Control Register................................................................................C-14
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

MOTOROLA MMC2001
xviii REFERENCE MANUAL
LIST OF ILLUSTRATIONS
Paragraph Title Page
C-18 Keypad Status Register .................................................................................C-14
C-19 Keypad Data Direction Register.....................................................................C-15
C-20 Keypad Data Register....................................................................................C-16
C-21 CS0 Control Register.....................................................................................C-17
C-22 CS1, CS2, CS3 Control Registers .................................................................C-17
C-23 EIM Configuration Register............................................................................C-21
C-24 PWM Control Registers..................................................................................C-23
C-25 PWM Period Registers...................................................................................C-26
C-26 PWM Width Registers....................................................................................C-26
C-27 PWM Count Registers....................................................................................C-27
C-28 Edge Port Pin Assignment Register...............................................................C-28
C-29 Edge Port Data Direction Register.................................................................C-28
C-30 Edge Port Data Register................................................................................C-29
C-31 Edge Port Flag Register.................................................................................C-29
C-32 ISPI Data Register.........................................................................................C-30
C-33 ISPI Control Register .....................................................................................C-31
C-34 ISPI Interval Control Register.........................................................................C-33
C-35 ISPI Status Register.......................................................................................C-34
C-36 UART Receive Register.................................................................................C-36
C-37 UART Transmit Register................................................................................C-37
C-38 UART Control Register 1 ...............................................................................C-38
C-39 UART Control Register 2 ...............................................................................C-40
C-40 UART BRG Register......................................................................................C-42
C-41 UART Status Register....................................................................................C-42
C-42 UART Test Register.......................................................................................C-44
C-43 UART Port Control Register...........................................................................C-44
C-44 UART Data Direction Register.......................................................................C-45
C-45 UART Port Data Register...............................................................................C-45
C-46 OnCE Command Register .............................................................................C-46
C-47 OnCE Control Register ..................................................................................C-47
C-48 OnCE Status Register....................................................................................C-50
C-49 Control State Register....................................................................................C-52
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

MMC2001 MOTOROLA
REFERENCE MANUAL xix
LIST OF TABLES
Paragraph Title Page
2-1 M•CORE Instruction Set .................................................................................2-6
2-2 M•CORE Bus Signals ..................................................................................2-11
2-3 Interface Requirements for Read and Write Cycles.......................................2-12
2-4 Termination Result Summary.........................................................................2-14
3-1 MMC2001 Module Address Map......................................................................3-1
3-2 MMC2001 Address Map ..................................................................................3-2
4-1 Pin Requirements in 144-Pin Package ..........................................................4-2
5-1 ROM Module Address Map..............................................................................5-1
6-1 Static RAM Module Address Map....................................................................6-1
7-1 Chip Select Address Range.............................................................................7-3
7-2 Interface Requirements for Read and Write Cycles .......................................7-5
7-3 EIM Memory Map ............................................................................................7-7
7-4 Wait State Control Field Settings....................................................................7-9
7-5 Data Port Size Field Settings.........................................................................7-10
7-6 Show Cycle Enable Field Settings.................................................................7-13
8-1 CPU Core and Peripherals Clock Source........................................................8-1
8-2 CPU Core and Peripherals in Low-Power Modes............................................8-7
9-1 Timer/Reset Module Address Map ..................................................................9-1
10-1 Interrupt Controller Address Map ..................................................................10-2
10-2 Interrupt Source Assignment ........................................................................10-6
11-1 UART Module Address Map ..........................................................................11-6
11-2 TxFL Field Settings........................................................................................11-9
11-3 RxFL Field Settings......................................................................................11-10
11-4 UART Pins GPIO Assignment......................................................................11-16
11-5 UART Low-Power Mode Operation..............................................................11-23
12-1 ISPI Module Address Map .............................................................................12-4
12-2 BAUD RATE Field Settings............................................................................12-7
12-3 CLOCK COUNT Field Settings......................................................................12-7
12-4 ISPI Low-Power Mode Operation.................................................................12-11
13-1 GPIO Edge Port Address Map ......................................................................13-2
13-2 EPPAx Field Settings.....................................................................................13-3
14-1 Keypad Port Column Modes..........................................................................14-2
14-2 Keypad Port Address Map ............................................................................14-2
15-1 PWM Address Map........................................................................................15-3
15-2 CLK SEL Field Settings..................................................................................15-6
15-3 PWM Range at 16 MHz .................................................................................15-8
15-4 PWM Low-Power Mode Operation.................................................................15-8
16-1 OnCE Register Addressing ...........................................................................16-8
16-2 Sequential Control Field Settings...................................................................16-9
16-3 Memory Breakpoint Control Field Settings...................................................16-10
16-4 Processor Mode Field Settings....................................................................16-12
A-1 Maximum Ratings ............................................................................................A-1
A-2 DC Electrical Specifications ...........................................................................A-1
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

MOTOROLA MMC2001
xx REFERENCE MANUAL
LIST OF TABLES
Paragraph Title Page
A-3 Clock Input Specifications................................................................................A-2
A-4 Reset, MOD Timing Specifications ................................................................A-2
A-5 External Interrupt Timing Specifications...........................................................A-3
A-6 EIM Timing Specifications................................................................................A-4
A-7 ISPI Timing Specifications ...............................................................................A-6
A-8 OnCE Timing Specifications ............................................................................A-9
C-1 MMC2001 Address Map ..................................................................................C-1
C-2 Interrupt Controller Address Map ....................................................................C-2
C-3 Timer/Reset Module Address Map .................................................................C-5
C-4 Keypad Port Address Map ............................................................................C-13
C-5 EIM Address Map ..........................................................................................C-16
C-6 Wait State Control Field Settings..................................................................C-18
C-7 Data Port Size Field Settings.........................................................................C-19
C-8 Chip-Select Address Range...........................................................................C-20
C-9 Show Cycle Enable Field Settings.................................................................C-22
C-10 PWM Address Map ......................................................................................C-22
C-11 Clock Select Field Values ..............................................................................C-25
C-12 GPIO Edge Port Address Map ......................................................................C-27
C-13 EPPAx Field Settings.....................................................................................C-28
C-14 Interval Mode Serial Peripheral Interface Address Map.................................C-30
C-15 BAUD RATE Values.......................................................................................C-32
C-16 CLOCK COUNT Values.................................................................................C-33
C-17 UART Module Address Map ..........................................................................C-35
C-18 TxFL Field Settings........................................................................................C-38
C-19 RxFL Field Settings........................................................................................C-39
C-20 OnCE Register Addressing............................................................................C-47
C-21 Sequential Control Field Definition.................................................................C-48
C-22 Memory Breakpoint Control Field Definition...................................................C-49
C-23 Processor Mode Field Definition....................................................................C-51
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...

MMC2001 INTRODUCTION MOTOROLA
REFERENCE MANUAL 1-1
SECTION 1
INTRODUCTION
The MMC2001 integrated processor incorporates the following functional units:
• M•CORE™ Integer Processor
— 32-bit RISC architecture
— Low power, high performance
• On-chip, 256-Kbyte ROM
• On-chip, 32-Kbyte SRAM with battery backup supply support
• Interrupt Controller
— Support for up to 32 interrupt sources
• External Interface Module (EIM)
— Transfers information between the MMC2001 and external memory or periph-
erals
— 22 address lines
— 16 data lines
— Chip select and wait state generation
— Bus watchdog timer
• Timer/Reset Module
— Crystal oscillator: generates the master clock signal for the time-of-day timer
from a 32.768-kHz external crystal
— Time-of-day timer: provides time-of-day information as well as an alarm clock
function
— Watchdog timer: resets the chip to recover from system failure
— Reset unit: provides low voltage detection input and backup power switching
for SRAM and the time-of-day timer
— Periodic interrupt timer
• Universal Asynchronous Receiver/Transmitter Module (UART)
— Two independent UART channels
— Asynchronous operation
— Baud rate generation
— Infrared (IR) interface support
• 16-bit general-purpose I/O port with support for keyboard scan/encode
• 8-bit general-purpose I/O port with support for edge/level sensitive external inter-
rupts
• Pulse-Width Modulation Module (PWM)
— Six independent PWM channels
— Programmable period
— Programmable duty cycle
— Periodic interrupt capability
— Pins can be configured as general-purpose I/O
• Interval Mode Serial Peripheral Interface (ISPI)
— Efficient communication with slower serial peripherals
Freescale Semiconductor, I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
nc...