Mountain Buggy terrain User manual

These instructions are for the Single Carrycot, which fits the following
model strollers:
Te r rain Single - T1204 Urban Single - U1204
SINGLE CARRYCOT INSTRUCTIONS
IMPORTANT, KEEP FOR FUTURE REFERENCE
ASCis1/3/04gen
1
WARNING
•Do not use this Carrycot until you have read and
understood the instructions!
•Carrycot is suitable for newborn baby to 6 months,or
until baby can sit up unaided.
•Before placing baby into position check that the
Carrycot is secure and will not tip or fall.
•Baby must not be in the Carrycot when it is being
fastened or removed from the stroller frame.
•The depth from the top of the mattress to the top of
the side of the Carrycot at, or at any position within
300mm/11.8in from the harness attachment points,
should not be reduced to less than 140mm/5.5in when
the mattress is in position. Mattresses purchased
separately should conform to BS1877 part 10.
•Do not use accessories not designed for your stroller
as they might be unsafe.
•Do not use the Carrycot to transport children in a
motor vehicle.
•Never leave your child unattended.
•Sunhood and seat need to be removed from stroller before fitting Carrycot.
•Store items removed in a dry safe place.
Unfasten seat from frame along
side tubes.
Unfasten strap underneath seat
at point A(does not apply toTerrain
model).
Push seat forward,then slide
fabric off seat support wire.
Remove seat support wire
from stroller frame at Band C.
3
1
2
Removing Seat
4
STAGE 1
Pull support wire out of
sunhood joint A. This
operation is child proof and
therefore requires a degree of
force. To assist in pulling
support wire out, push
against buggy frame with other
hand B.
Repeat step (1) on other
side.
Unfasten sunhood fabric
from stroller frame and seat
near handle bar.
3
1
Removing Sunhood (both models)
2
A
B
Sunhood Joint
These instructions are for the Single Carrycot, which fits the following
model strollers:
Te r rain Single - T1204 Urban Single - U1204
SINGLE CARRYCOT INSTRUCTIONS
IMPORTANT, KEEP FOR FUTURE REFERENCE
ASCis1/3/04gen
1
WARNING
•Do not use this Carrycot until you have read and
understood the instructions!
•Carrycot is suitable for newborn baby to 6 months,or
until baby can sit up unaided.
•Before placing baby into position check that the
Carrycot is secure and will not tip or fall.
•Baby must not be in the Carrycot when it is being
fastened or removed from the stroller frame.
•The depth from the top of the mattress to the top of
the side of the Carrycot at, or at any position within
300mm/11.8in from the harness attachment points,
should not be reduced to less than 140mm/5.5in when
the mattress is in position. Mattresses purchased
separately should conform to BS1877 part 10.
•Do not use accessories not designed for your stroller
as they might be unsafe.
•Do not use the Carrycot to transport children in a
motor vehicle.
•Never leave your child unattended.
•Sunhood and seat need to be removed from stroller before fitting Carrycot.
•Store items removed in a dry safe place.
Unfasten seat from frame along
side tubes.
Unfasten strap underneath seat
at point A(does not apply toTerrain
model).
Push seat forward,then slide
fabric off seat support wire.
Remove seat support wire
from stroller frame at Band C.
3
1
2
Removing Seat
4
STAGE 1
Pull support wire out of
sunhood joint A. This
operation is child proof and
therefore requires a degree of
force. To assist in pulling
support wire out, push
against buggy frame with other
hand B.
Repeat step (1) on other
side.
Unfasten sunhood fabric
from stroller frame and seat
near handle bar.
3
1
Removing Sunhood (both models)
2
A
B
Sunhood Joint

4 x Snap Locks
1 x
Allen Key
2 x
Screws
Fitting Snap Locks to Carrycot
1Place one of the Snap Locks over hole A. Make sure it is aligned
correctly with the hole in Carrycot.
Using Allen Key, rotate screw in Snap Lock in a clockwise direction
until screw is tight. Snap Lock is firmly attached to Carrycot, but can still
rotate.
2
Repeat steps 1 & 2 to fit Snap Lock to hole C.
Place one of the screws and cover buttons into hole B. Using Allen
Key rotate screw in a clockwise direction until screw is tight.
Repeat steps 1,2,3 and 4 to fit Snap Locks to other side of Carrycot.
4
3
5
Repeat steps 1 & 2 to fit Snap Lock to hole B.
Place one of the screws and cover buttons into hole C. Using Allen
Key rotate screw in a clockwise direction until screw is tight.
Repeat steps 1,2,6 & 7 to fit Snap Locks to other side of Carrycot.
7
6
8
Fitting Carrycot to Frame
•When placing Carrycot,
ensure front end of Carrycot is
vertically above footplate within
shaded zone shown.
X
Y
sunhood joint
X
tube joint
Y
Place Snap Lock X directly
above sunhood joint.
Place Snap Lock Y directly
above tube joint.
Close all 4 Snap Locks down flat, making sure you hear the lock
“click” indicating they are fully locked.
3
OPEN POSITION CLOSED POSITION
Removing Carrycot from Frame
Open all 4 Snap Locks on frame and lift Carrycot off buggy frame.
“CLICK”
•Two Snap Locks are fitted to each side of Carrycot.
•Spare hole on each side, is fitted with cover button and screw.
Carrycot
WARNING
•Check Carrycot is horizontal and is located correctly
onto stroller frame. Refer back to diagrams for your
model to ensure positioning of Snap Locks is correct.
•Check Snap Locks are closed and firmly attached to
frame and Carrycot will not tip or fall.
•Do not use Carrycot if you are unable to secure. In this
case, contact store where stroller was purchased or
distributor for your country, for more help.
•Always remove Carrycot before collapsing buggy!
TERRAIN URBAN
STAGE 2
PARTS LIST
•Follow instructions for your model
WARNING
Using the Allen Key, check that all four Snap Locks are
firmly tightened,and they will not separate from Carrycot.
STAGE 3
•Ensure Snap Locks are rotated
so screw holes are on top.
Open all four Snap Locks by lifting levers up.
Place Carrycot onto frame, firmly pushing Snap Locks into position,
so they butt up to joints indicated in the following diagram for your
model.
1
2
2 x Cover Buttons
4 x Snap Locks
1 x
Allen Key
2 x
Screws
Fitting Snap Locks to Carrycot
1Place one of the Snap Locks over hole A. Make sure it is aligned
correctly with the hole in Carrycot.
Using Allen Key, rotate screw in Snap Lock in a clockwise direction
until screw is tight. Snap Lock is firmly attached to Carrycot, but can still
rotate.
2
Repeat steps 1 & 2 to fit Snap Lock to hole C.
Place one of the screws and cover buttons into hole B. Using Allen
Key rotate screw in a clockwise direction until screw is tight.
Repeat steps 1,2,3 and 4 to fit Snap Locks to other side of Carrycot.
4
3
5
Repeat steps 1 & 2 to fit Snap Lock to hole B.
Place one of the screws and cover buttons into hole C. Using Allen
Key rotate screw in a clockwise direction until screw is tight.
Repeat steps 1,2,6 & 7 to fit Snap Locks to other side of Carrycot.
7
6
8
Fitting Carrycot to Frame
•When placing Carrycot,
ensure front end of Carrycot is
vertically above footplate within
shaded zone shown.
X
Y
sunhood joint
X
tube joint
Y
Place Snap Lock X directly
above sunhood joint.
Place Snap Lock Y directly
above tube joint.
Close all 4 Snap Locks down flat, making sure you hear the lock
“click” indicating they are fully locked.
3
OPEN POSITION CLOSED POSITION
Removing Carrycot from Frame
Open all 4 Snap Locks on frame and lift Carrycot off buggy frame.
“CLICK”
•Two Snap Locks are fitted to each side of Carrycot.
•Spare hole on each side, is fitted with cover button and screw.
Carrycot
WARNING
•Check Carrycot is horizontal and is located correctly
onto stroller frame. Refer back to diagrams for your
model to ensure positioning of Snap Locks is correct.
•Check Snap Locks are closed and firmly attached to
frame and Carrycot will not tip or fall.
•Do not use Carrycot if you are unable to secure. In this
case, contact store where stroller was purchased or
distributor for your country, for more help.
•Always remove Carrycot before collapsing buggy!
TERRAIN URBAN
STAGE 2
PARTS LIST
•Follow instructions for your model
WARNING
Using the Allen Key, check that all four Snap Locks are
firmly tightened,and they will not separate from Carrycot.
STAGE 3
•Ensure Snap Locks are rotated
so screw holes are on top.
Open all four Snap Locks by lifting levers up.
Place Carrycot onto frame, firmly pushing Snap Locks into position,
so they butt up to joints indicated in the following diagram for your
model.
1
2
2 x Cover Buttons