Moxa Technologies MiiNePort E Series User manual

P/N: 1802000012013
*1802000012013*
MiiNePort E Series
Quick Installation Guide
Version 1.1, November 2019
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll
-free: 1-888-669-2872
Tel:
1-714-528-6777
Fax:
1-714-528-6778
Moxa China (Shanghai office):
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe:
Tel:
[phone]
Fax:
[phone]
Moxa Asia-Pacific:
Tel:
[phone]
Fax:
[phone]
Moxa India:
Tel:
[phone]
Fax:
[phone]

2019 Moxa Inc. All rights reserved.

- 2 -
Overview
The Moxa MiiNePort E series of serial-to-Ethernet embedded modules
comes with four models: two standard operating temperature models
(MiiNePort E, MiiNePort E-H) and two wide operating temperature
models (MiiNePort E-T, MiiNePort E-H-T). Moxa provides a starter kit for
each MiiNePort E series module; each starter kit contains an evaluation
board that can be used to evaluate the modules and to develop your
own application. The following table lists the model names of all
MiiNePort E series modules, along with the model names of the
corresponding starter kits.
Available Modules
•MiiNePort E1: Embedded device server for TTL devices, drop-in
module, 10/100M with RJ45 connector, 50 bps to 230.4 Kbps
baudrate, 0 to 55°C operating temperature
•MiiNePort E1-T: Embedded device server for TTL devices, drop-in
module, 10/100M with RJ45 connector, 50 bps to 230.4 Kbps
baudrate, -40°C to 85°C operating temperature
•MiiNePort E1-H: Embedded device server for TTL devices, drop-in
module, 10/100M with RJ45 connector, 50 bps to 921.6 Kbps
baudrate, 0 to 55°C operating temperature
•MiiNePort E1-H-T: Embedded device server for TTL devices, drop-
in module, 10/100M with RJ45 connector, 50 bps to 921.6 Kbps
baudrate, -40 to 85°C operating temperature
•MiiNePort E2: Embedded device server for TTL devices, drop-in
module, 10/100M without RJ45 connector, 50 bps to 230.4 Kbps
baudrate, 0 to 55°C operating temperature
•MiiNePort E2-T: Embedded device server for TTL devices, drop-in
module, 10/100M without RJ45 connector, 50 bps to 230.4 Kbps
baudrate, -40 to 85°C operating temperature
•MiiNePort E2-H: Embedded device server for TTL devices, drop-in
module, 10/100M without RJ45 connector, 50 bps to 921.6 Kbps
baudrate, 0 to 55°C operating temperature
•MiiNePort E2-H-T: Embedded device server for TTL devices, drop-
in module, 10/100M without RJ45 connector, 50 bps to 921.6 Kbps
baudrate, -40 to 85°C operating temperature
•MiiNePort E3: Embedded device server for TTL devices, pin-
header module, 10/100M with RJ45 connector, 50 bps to 230.4
Kbps baudrate, 0 to 55°C operating temperature
•MiiNePort E3-T: Embedded device server for TTL devices, pin-
header module, 10/100M with RJ45 connector, 50 bps to 230.4
Kbps baudrate, -40 to 85°C operating temperature
•MiiNePort E3-H: Embedded device server for TTL devices, pin-
header module, 10/100M with RJ45 connector, 50 bps to 921.6
Kbps baudrate, 0 to 55°C operating temperature
•MiiNePort E3-H-T: Embedded device server for TTL devices, pin-
header module, 10/100M with RJ45 connector, 50 bps to 921.6
Kbps baudrate, -40 to 85°C operating temperature

- 3 -
Available Starter Kits
•MiiNePort E1-ST: Starter kit for the MiiNePort E1 Series, module
included
•MiiNePort E1-H-ST: Starter kit for the MiiNePort E1-H Series,
module included
•MiiNePort E2-ST: Starter kit for the MiiNePort E2 Series, module
included
•MiiNePort E2-H-ST: Starter kit for the MiiNePort E2-H Series,
module included
•MiiNePort E3-ST: Starter kit for the MiiNePort E3 Series, module
included
•MiiNePort E3-H-ST: Starter kit for the MiiNePort E3-H Series,
module included
Package Checklist
Each MiiNePort E Series starter kit package contains the following
items:
•1 MiiNePort E Series module
•1 MiiNePort E Series evaluation board
•1 universal power adapter
•2 power cords
•1 null modem serial cable
•1 cross-over Ethernet cable
•1 product warranty booklet
•2 flat cables (MiiNePort E3 Series only)
•1 pack of screw and spacer (MiiNePort E3 Series only)
•Quick installation guide (print)
•Warranty card
NOTE
Please notify your sales representative if any of the above
items are missing or damaged.
Hardware Installation Procedure
Follow these steps to prepare the module and evaluation board for
testing and application development.
STEP 1:
Plug the MiiNePort E module into the sockets on the top of
the evaluation board.
ATTENTION
For detailed information about the pin assignments, wiring, LED
indicators, and board layouts, refer to Chapter 1 and 2 of the
MiiNePort E Series User’s Manual.
STEP 2:
Connect the 12 to 48 VDC power line with the evaluation
board’s power jack.
STEP 3:
Switch on the power switch
STEP 4:
Use an RJ45 Ethernet cable to connect the MiiNePort E
module to an Ethernet network.

- 4 -
STEP 5:
Use the serial data cable to connect the evaluation board to a
serial device.
Software Utility Installation Procedure
Use the following installation procedure for each MiiNePort E model:
Software Installation
For software installation, download the relevant utilities from Moxa's
website: https://www.moxa.com/en/support
1. Start the Device Search Utility (DSU) setup program to begin
the installation. When the Welcome window opens, click Next.
2. Click Install to install program files in the default directory.
3. The Installing window reports the progress of the installation.
4. Click Finish to complete the installation.
Module Configuration
1. Start the DSU program.
2. Select the Search function from the function icons.
3. After the search is finished, all MiiNePort E modules that were found
will be shown in the search window. If you locate more than one
module connected to this network, refer to the MAC address on the
module(s) to determine the modules you wish to configure.
4. Double-click on the MiiNePort E module you wish to configure; your
web browser will be activated with the MiiNePort E’s web console.
5. The default IP address of the MiiNePort E is 192.168.127.254, and
the default login credentials:
username: admin
password: moxa
6. Refer to Chapter 7 of the MiiNePort E Series User’s Manual for
additional configuration instructions.
Evaluation Board Layout
E1 Series

- 5 -
E2 Series
Number
Description
1
MiiNePort E2 Module Location
2
Ethernet RJ45 Connector
3
Serial Interface Jumper
4
Power Switch
5
Power Jack
6
Power and Ready LED
7
DB9 Male Connector
8
Serial Port Status LED
9
Digital IO Terminal Block
10
Digital Output LED
11
Digital Input/Output Mode
12
Digital Input Switch
13
Circuit Pad

- 6 -
E3 Series
Number
Description
1
PoE Pin
2
MiiNePort E3 Module Location
3
Serial Interface Jumper
4
Power Switch
5
Power Jack
6
Power & Ready LED
7
DB9 Male Connector
8
Serial Port Status LED
9
Digital IO Terminal Block
10
Digital Output LED
11
Digital Input/Output Mode
12
Digital Input Switch
13
Circuit Pad

- 7 -
Pin Assignment
E1 Series
Serial Signal Pins (MiiNePort E1 Series Modules)
Pin
Function
1
GND
2
VCC
3
Reset
4
Data Out
5
Data In
6
Ready/RTSa
7
Reset to Defaultb
8
CTSc
a. Pin 6 can be configured as Ready/RTS (RequesttoSend), Ready/DO,
or RS-485 Tx Enabled (the default it Ready/RTS).
b. Pin 7 can be configured as Reset to Default, DIO, DTR, or RS-485
Tx Enabled (the default is Reset to Default).
c. Pin 8 can be configured as CTS (CleartoSend), DI, or DSR (the
default is CTS).
E2 Series
The bottom view of the MiiNePort E2 Series Module
JP1
Pin
Signal Name
Function
1
Ethernet Tx+
Ethernet Transmit Data+
2
Ethernet Tx-
Ethernet Transmit Data-
3
Ethernet Rx+
Ethernet Receive Data+
4
Ethernet Rx-
Ethernet Receive Data-
JP2
Pin
Signal Name
Function
1
100M LED
Ethernet 100M LED
2
10M LED
Ethernet 10M LED
3
LRXD
Receive Serial Data
4
LTXD
Transmit Serial Data
5
LDCD
Data Carrier Detect
6
RS485_EN
RS-485 Enable
7
LRTS
Request To Send
8
LDTR
Data Terminal Ready
9
LDSR
Data Set Ready
10
LCTS
Clear To Send

- 8 -
JP3
Pin
Signal Name
Function
1
DIO0
Programmable Input/Output
2
DIO1
Programmable Input/Output
3
DIO2
Programmable Input/Output
4
DIO3
Programmable Input/Output
5
Reserved
N/A
6
Reserved
N/A
7
SW Reset
Reset To Factory Default
8
GND
Circuit Ground
9
Ready LED
System is Ready
10
VCC
Power Supply
E3 Series
The bottom view of the MiiNePort E3 Series Module
Ethernet Pins (JP2)
Pin
Signal Name
Function
1
Reserve
N/A
2
Reserve
N/A
3
Reserve
N/A
4
Reserve
N/A
5
PoE signal pair 1
PoE power from Tx signal
6
PoE spare pair 1
PoE power from RJ45 4, 5 pin
7
PoE signal pair 2
PoE power from Rx signal
8
PoE spare pair 2
PoE power from RJ45 7, 7 pin
Serial Pins and Power Pins (JP4)
Pin
Signal Name
Function
1
Serial Rx
Receive Serial Data
2
Ready LED
System is Ready
3
Serial Tx
Transmit Serial Data
4
GPIO
Programmable I/O, DIO0
5
DCD
Receive Line Signal Detector
6
GPIO
Programmable I/O, DIO2
7
RS485_EN0
RS-485 Enabled
8
GPIO
Programmable I/O, DIO3
9
RTS
Request to Send
10
GPIO
Programmable I/O, DIO1
11
DTR
Data Terminal Ready
12
Reserve
N/A

- 9 -
Pin
Signal Name
Function
13
DSR
Data Set Ready
14
Reserve
N/A
15
CTS
Clear to Send
16
SW_Reset
Reset to Factory Default
17
Reserve
N/A
18
Reserve
N/A
19
GND
Circuit Ground
20
VCC
Power Supply
Ethernet Port Pins
RJ45
Pin
Signal
1
Tx+
2
Tx-
3
Rx+
6
Rx-
Evaluation Board Serial Port
DB9 Male
Pin
RS-232
RS-485-2W
1
DCD
–
2
RxD
–
3
TxD
D+
4
DTR
D-
5
GND
GND
6
DSR
–
7
RTS
–
8
CTS
–
9
–
–
Certification
This product complies with Chinese RoHS (Restriction of
Hazardous Substances) regulations for Electronic
Information Products.