Moxa Technologies MGate 4101-MB-PBS User manual

P/N: 1802041010016
*1802041010016*
MGate 4101-MB-PBS Series
Quick Installation Guide
Version 6.1, January 2021
Technical Support Contact Information
www.moxa.com/support

2021 Moxa Inc. All rights reserved.

- 2 -
Overview
The MGate™ 4101-MB-PBS and 4101I-MB-PBS are 1-port Modbus serial
to PROFIBUS slave gateways that provide protocol conversion for users
who need to connect Modbus devices to Siemens PLCs.
Package Checklist
Before installing the MGate 4101-MB-PBS or 4101I-MB-PBS, verify that
the package contains the following items:
•1 MGate 4101-MB-PBS or 4101I-MB-PBS Modbus to PROFIBUS slave
gateway
•RJ45 to DB9 cable (for use with the console)
•Quick installation guide (printed)
•Warranty Card
Please notify your sales representative if any of the above items are
missing or damaged.
Optional Accessories
•WK-36-02: Wall mounting kit
•Mini DB9F-to-TB Adaptor: DB9 female to terminal block adapter
NOTE
This product is intended to be supplied by a Listed Power Adapter
or DC power source marked "L.P.S." (or "Limited Power Source"),
rated 12
to 48 VDC, 275 mA minimum, Tma = 75°C minimum.
If need further assistance, please contact MOXA
Inc.
for further
information.
Hardware Introduction
LED Indicators
LED
Color
Function
PWR1
Green
Power is on
Off
Power is off
PWR2
Green
Power is on
Off
Power is off
Ready
Green
Gateway is operational
Red
Check Configuration failed or Set Parameter
failed
Off
Power is off or fault condition exists
P1 TX/RX
(Modbus Serial)
Green
Serial device is transmitting data
Orange
Serial device is receiving data
Off
No data is flowing to or from the serial port
P2 Status
(PROFIBUS)
Green
Steady: Data is exchanging
Red Steady: Baudrate automatically identified.
Wrong Slave Address or CHK_PRM or
CHK_CFG will keep in steady red.
Off
PROFIBUS offline

- 3 -
The MGate 4101-MB-PBS and 4101I-MB-PBS both come with an RJ45 to
DB9 cable for connecting to a serial console.
Reset Button
The reset button is used to load factory defaults. Use a pointed object
such as a straightened paper clip to hold the reset button down for five
seconds. Release the reset button when the Ready LED stops blinking.
Pull-high, Pull-low, and Terminator for RS-485
Remove the MGate 4101-MB-PBS’s top cover to adjust the DIP switches
for each serial port’s pull-high resistor, pull-low resistor, and terminator.
SW
1
2
3
Pull-high
resistor
Pull-low
resistor
Terminator
ON
1 kilo-ohm
1 kilo-ohm
120 ohms
OFF
150 kilo-ohms*
150 kilo-ohms*
–*
*Default
Hardware Installation Procedure
STEP 1:
Connect the power adapter. Make sure that the adapter is
connected to an earthed socket.
Connect the 12 to 48 VDC
power line with the
MGate 4101-MB-PBS/4101I-MB-PBS
series’ terminal block, or connect the
DIN rail power supply
with the
MGate 4101-MB-PBS/4101I-MB-PBS device’s
terminal
block.
STEP 2:
Use a PROFIBUS cable to connect the unit to a PROFIBUS PLC
or
other PROFIBUS master.
STEP 3:
Connect your device to the unit’s serial port.
STEP 4:
Attach the device to a DIN rail or the wall. The MGate
4101
-MB-PBS/4101I-MB-PBS series is designed to be
attached to a DIN rail or mounted on a wall. For DIN rail
mounting, push down the spring and properly attach it to the
DIN rail until it snaps into place. For wall
mounting, install the
wall mount kit (optional) first, and then screw the device onto
the wall.

- 4 -
Wall or Cabinet Mounting
Mounting the MGate 4101-MB-PBS on to a wall
requires two screws. The heads of the screws
should be 5 to 7 mm in diameter, the shafts should
be 3 to 4 mm in diameter, and the l
ength of the
screws should be more than 10.5 mm.
The following figure illustrates the two mounting options:
Software Installation Information
To install MGate Manager, please download it from Moxa's website at
http://www.moxa.com. Then, click the Installation button and follow the
onscreen instructions. For more detailed information about MGate
Manager, please refer to the User’s Manual.
Pin Assignments
Modbus Serial Port (Male DB9)
Pin RS-232
RS-422/
RS-485 (4W)
RS-485 (2W)
1
DCD
TxD-(A)
–
2
RXD
TxD+(B)
–
3
TXD
RxD+(B)
Data+(B)
4
DTR
RxD-(A)
Data-(A)
5
GND
GND
GND
6
DSR
–
–
7
RTS
–
–
8
CTS
–
–
9
–
–
–
PROFIBUS Serial Port (Female DB9)
PIN
Signal Name
1
–
2
–
3
PROFIBUS D+
4
RTS
5
Signal common
6
5V
7
–
8
PROFIBUS D-
9
–

- 5 -
Power Input and Relay Output Pinouts
V2+ V2-
V1+ V1-
Shielded
Ground
DC
Power
Input 2
DC
Power
Input 2
N.O. Common N.C.
DC
Power
Input 1
DC
Power
Input 1
Specifications
Power Requirements
Power Input
12 to 48 VDC
Power Consumption
275 mA (max.)
Operating Temperature
Standard Model:
0 to 60°C (32 to 140°F)
Wide Temp. Model:
-40 to 75°C (-40 to 167°F)
Operating Humidity
5 to 95% RH
Dimensions
36 x 105 x 140 mm (1.42 x 4.13 x 5.51 in)
Reliability
Alert Tools
Built-in buzzer
MTBF
MGate 4101-MB-PBS Series: 1,537,948 hrs
MGate 4101I-MB-PBS Series: 1,315,666 hrs
1. ATEX Certificate No.: DEMKO 14 ATEX 1311X
2. Protection Method: Ex nA nC IIC T4 Gc
3. IECEx Certificate No: IECEx UL 14.0065X
4. Standards: EN 60079-0:2012+A11:2013; EN 60079-15:2010;
IEC 60079-0 Ed.6; IEC 60079-15 Ed.4.
5. Conditions of safe usage:
•This equipment shall only be used in an area of not more than
pollution degree 2, as defined in IEC/EN 60664-1.
•This equipment shall be installed in an enclosure that provides a
degree of protection not less than IP54 in accordance with IEC/EN
60079-15. The enclosure should only be accessible by using a
tool (wrench, screw driver, etc.).
•Transient protection shall be provided that is set at a level not
exceeding 140% of the peak rated voltage value at the
equipment’s power supply terminals.
6. Ambient Temperature:
-40°C ≤ Tamb ≤75°C for MGate 4101X-MB-PBS-T models;
0°C ≤Tamb ≤60°C for MGate 4101X-MB-PBS models.

- 6 -
Terminal Block Torque Value and Wire Gauge:
•Terminal block (the plug matched socket): rated at 300 V, 15 A,
105°C, 12-28 AWG (0.0804 mm2 to 3.31 mm2) wire size, torque
value 4.5 lb-in (0.509 N-m). The input terminal cable size: 14 AWG
(2.1 mm²).
ATTENTION
These devices are open
-type devices that need
be installed in an
enclosure only accessible with the use of a tool, suitable for the
environment.
NOTE
This equipment is suitable for use in Class I, Division 2, Groups A,
B, C, and D or nonhazardous locations only.”
WARNING
EXPLOSION HAZARD
—Do not disconnect equipment unless
power has been
switched off or the area is known to be
non-hazardous.
WARNING
EXPLOSION HAZARD
—Substitution of any components may
impair suitability for Class I, Division 2.
Moxa Inc.
No. 1111, Heping Rd., Bade Dist., Taoyuan City 334004, Taiwan