Moxa Technologies NPort Z2150 User manual

– 1 – – 2 – – 3 –
P/N: 1802021504011
*1802021504011*
NPort Z2150
Quick Installation Guide
Second Edition, July 2015
Overview
The NPort Z2150 is a reliable wireless serial I/O with support for
serial to ZigBee communications. The NPort Z2150 can act as a
ZigBee Coordinator, ZigBee Router or ZigBee End Device. Any
serial device can be connected by the NPort Z2150 and exchange
data via Personal Area Network (PAN).
Package Checklist
Before installing the NPort Z2150, verify that the package contains
the following items:
Standard Accessories
•NPort Z2150
•Documentation & Software CD
•Warranty statement
•Quick Installation Guide
•2.4 GHz, omni-directional antenna
Optional Accessories
•DK-35A: DIN-rail mounting kit (35 mm)
NOTE: Please notify your sales representative if any of the above
items are missing or damaged.
Hardware Introduction
LED Indicators
LED
Color
Descriptions
Ready/Fault
Green
On: System power is on
Blinking: Pull down the reset button
Red
Blinking:
1) Node ID conflict
2) Destination node ID disappeared
ZigBee Link Green
Coordinator:
ON: ZigBee PAN initialized successfully
Blinking: ZigBee Tx/Rx
Off: ZigBee PAN initialization failure
Router:
On: Joined ZigBee PAN successfully
Blinking: ZigBee Tx/Rx
Off: Failure to join ZigBee PAN
End Device:
On: Joined ZigBee PAN successfully
Blinking: ZigBee Tx/Rx
Off: Failure to join ZigBee PAN/ parent
node removed
Serial Tx/Rx
Green
Serial data output to serial port
Orange
Serial data input from serial port
The NPort Z2150 models have one serial port. All models support
RS-232/422/485 with DB9 connectors.
Reset Button
The reset button is used to load factory defaults. Use a pointed
object such as a straightened paper clip to hold the reset button
down for five seconds. Release the reset button when the Ready
LED stops blinking.
DIP Switch
Serial Connection
1
Console Mode
ON
Operation Mode
OFF
NOTE
2 reserved for future use.
Pull High/Low Resistors for RS-422/485
You may need to set the pull high/low resistors when termination
resistors are used for certain RS-422 or RS-485 environments.
SW
1
2
3
4
Pull High
Pull Low
Terminator
Reserved
ON
1KΩ
1KΩ
120KΩ
–
Default
OFF
150KΩ
150KΩ
–
–
NOTE
Do not use the 1KΩ setting while in RS-232 mode. Doing so
will degrade the RS
-232 signals and reduce the effective
communication distance.

– 4 – – 5 – – 6 –
www.moxa.com/support
The Americas:
[phone] (toll-free: 1-888-669-2872)
Europe:
[phone]
Asia-Pacific:
[phone]
China:
[phone] (toll-free: 800-820-5036)
2015 Moxa Inc. All rights reserved.
First-time Hardware Installation
STEP 1:
After removing the NPort Z2150 from the box, set the
DIP-switch to console mode and use a cross-over serial
cable to connect the NPort’s DB9 serial port directly to
your computer’s serial port to configure.
STEP 2:
Attach the power adaptor to the NPort and then plug the
adaptor into an electrical outlet.
STEP 3:
Configure the NPort Z2150 through the serial port. See
the next section for software installation information.
Software Installation Information
Insert the Documentation & Software CD. A window should open
with several options displayed:
•Click Documents and select “NPort Z2150 Series User’s
Manual” to view the user’s manual.
•Click Install Utility and follow the on-screen instructions to
install the ZigBee Configuration Utility. This utility can be used
to search for NPort Z2150 units via serial ports.
Pin Assignments and Cable Wiring
PIN RS-232
RS-422,
4w RS-485
2w RS-485
1
DCD
TxD-(A)
–
2
RXD
TxD+(B)
–
3
TXD
RxD+(B)
Data+(B)
4
DTR
RxD-(A)
Data-(A)
5
GND
GND
GND
6
DSR
–
–
7
RTS
–
–
8
CTS
–
–
9
–
–
–
Specifications
Power Requirements
Input Voltage
12 to 48 VDC
Power Consumption
45 mA @ 12 V
Connector
Power Jack
Physical Characteristics
Weight
340g
Dimension
Without ears:
With ears:
52 x 80 x 22 mm (2.05 x 3.15 x 0.87 in)
75 x 80 x 22 mm (2.95 x 3.15 x 0.87 in)
Regulatory Approvals
EMC
CE (EN55022 Class A, EN55024), FCC Part
15 Subpart B Class A
Safety
UL (UL60950-1), LVD (EN60950-1)
WARNING
1.
This equipment is intended to be used in a Restricted
Access Location.
2.
This product is intended to be supplied by an UL
60950-1 and IEC 60950-1 certified power supply
marked “LPS” and rated output rating: 12 to 48
VDC,
45 mA @ 12 V minimum, 75°C.