MSA Ultra Elite-PF User manual

MSAsafety.com
Operating Manual
Ultra Elite Full Face Mask –
Positive Pressure
Order No.: 10110550/02

MSA Europe GmbH
Schlüsselstrasse 12
8645 Rapperswil-Jona
Switzerland
[e-mail]
www.MSAsafety.com
© MSA 2018 All rights reserved

Ultra Elite Full Face Mask – Positive Pressure 3
GB
Contents
1 Safety Regulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1 Correct Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.2 Liability Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1 Mask Versions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.2 Marking/Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3 Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.1 Donning the Mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.2 Leak Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.3 Removing the Mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4 Cleaning, Disinfection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4.1 Cleaning/Disinfection with a Washing Machine . . . . . . . . . . . . . . . . 10
4.2 Cleaning/Disinfection with an Ultrasonic Cleaner . . . . . . . . . . . . . . . 10
4.3 Cleaning by Hand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
4.4 Disinfection by Hand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
5 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.1 Maintenance Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.2 Maintenance Intervals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.3 Maintenance of the Exhalation Valve . . . . . . . . . . . . . . . . . . . . . . . . 13
5.4 Replacing the Speech Diaphragm . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.5 Tightness Test of the Mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.6 Visual Test and Function Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
6 Safekeeping and Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7 Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7.1 Exploded View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
7.2 Full Face Mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7.3 Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7.4 Replacement Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Ultra Elite Full Face Mask – Positive Pressure 4
Safety Regulations
GB
1 Safety Regulations
1.1 Correct Use
Series Ultra Elite Full Face Mask with positive pressure connection according to EN 148-3 or special
manufacturer type are not complete respiratory protective devices by themselves, but serve as
facepieces [EN 136 CL3+] for use with respiratory filters, compressed air breathing apparatus, fresh
air hose breathing apparatus and compressed air line breathing apparatus.
The mask as part of a respiratory protective device ensures an appropriately tight fit of the user’s face
against the ambient atmosphere.
It is imperative that this operating manual be read and observed when using the device. In particular,
the safety instructions, as well as the information for the use and operation of the device, must be care-
fully read and observed. Furthermore, the national regulations applicable in the user's country must be
taken into account for a safe use.
WARNING!
This product is supporting life and health. Inappropriate use, maintenance or servicing may affect the
function of the device and thereby seriously compromise the user's life.
Before use the product operability must be verified. The product must not be used if the function test
is unsuccessful, it is damaged, a competent servicing/maintenance has not been made, genuine MSA
spare parts have not been used.
Alternative use, or use outside this specification will be considered as non-compliance. This also
applies especially to unauthorized alterations to the product and to commissioning work that has not
been carried out by MSA or authorized persons.
1.2 Liability Information
MSA accepts no liability in cases where the product has been used inappropriately or not as intended.
The selection and use of the product are the exclusive responsibility of the individual operator.
Product liability claims, warranties also as guarantees made by MSA with respect to the product are
voided if it is not used, serviced, or maintained in accordance with the instructions in this manual.
Changes and modifications not expressly approved by the manufacturer will void the user’s authority
to operate the equipment.

Ultra Elite Full Face Mask – Positive Pressure 5
Description
GB
2 Description
The face blank is made of a special soft rubber compound and assures a snug, comfortable fit and a
tight seal. The face blank is also available in yellow silicone. Some versions of the mask are also avail-
able in small size.
The inhalation air flows from the connector of the mask past the inhalation valve to the inside of the
lens [thus keeping the lens largely fog-free] and then through the check valves into the nose cup.
The exhalation air passes through the exhalation valve directly to the ambient air.
Fig. 1 Overview full face mask
1 Face blank 5 Carrying strap
2 Head strap 6 Connector with inhalation and exhalation valves
3 Buckle 7 Speech diaphragm
4 Nose cup with valve 8 Lens
1
2
8
4
5
3
7
6

Ultra Elite Full Face Mask – Positive Pressure 6
Description
GB
2.1 Mask Versions
Standard Thread Connector M45 x 3
Ultra Elite-PF • Standard version
Ultra Elite-PF small • as standard version, small size
Ultra Elite-PF-Si • as standard version, face blank, inner mask and harness made
from silicone
Ultra Elite-PF-EZ • as standard version, special Nomex harness
Ultra Elite-PF-EZ small • as standard version, special Nomex harness, small size
MSA Plug-in Connector
Ultra Elite-PS • Standard version
Ultra Elite-PS-small • as standard version, small size
Ultra Elite-PS-Si • as standard version, face blank, inner mask and harness made
from silicone
Ultra Elite-PS-EZ • as standard version, special Nomex harness
Ultra Elite-PS-EZ small • as standard version, special Nomex harness, small size
Ultra Elite-PS Transponder • as standard version, with transponder
AutoMaXX Plug-in Connector
Ultra Elite-PS-MaXX • Standard version
Ultra Elite-PS-MaXX small • as standard version, small size
Ultra Elite-PS-MaXX-Si • as standard version, face blank, inner mask and harness made
from silicone
Ultra Elite-PS-MaXX-EZ • as standard version, special Nomex harness
Ultra Elite-PS-MaXX-EZ small • as standard version, special Nomex harness, small size
Ultra Elite-PS-MaXX Tran-
sponder • as standard version, with transponder
Ultra Elite-PS-MaXX small
Transponder • as standard version, with transponder, small size
Ultra Elite-PS-MaXX large
Transponder • as standard version, with transponder, large size
Ultra Elite-PS-MaXX-Si Tran-
sponder
• as standard version, with transponder, face blank, inner mask
and harness made from silicone
ESA Plug-in Connector
Ultra Elite-PF-ESA • Standard version
Ultra Elite-PF-ESA small • as standard version, small size
Ultra Elite-PF-ESA-Si • as standard version, face blank, inner mask and harness made
from silicone
Ultra Elite-PF-ESA-EZ • as standard version, special Nomex harness
Ultra Elite-PF-ESA-EZ small • as standard version, special Nomex harness, small size

Ultra Elite Full Face Mask – Positive Pressure 7
Description
GB
2.2 Marking/Certification
Marking
The mask is marked on the outer face blank as shown in Fig. 2:
Fig. 2 Marking of mask body
Certification
Mask with Lenses from Polycarbonate with Silicate Coating
The masks according to chapter 2.1
comply with the following directives, standards or standardised documents:
The Declaration of Conformity can be found under the following link: https://MSAsafety.com/DoC
1 Mask Version
2 Part Number
3 Marking [date code, serial number]
4 CE-marking with notified body number
[DEKRA EXAM, Zertifizierungsstelle Dinnendahlstr. 9, 44809 Bochum]
5X: ATEX classification A, B or C according to the Lens typ.
6 EN standard, class
Directive 2014/34/EU [ATEX] : BVS 05 ATEX H 027 X
for masks
I M1
II 1 G IIA T6 -40 °C Ta +60 °C
II 1 D
Directive 89/686/EC or
Regulation (EU) 2016/425,
respectively
:EN 136 CL3+
0158
DEKRA EXAM GmbH, Dinnendahlstr. 9, 44809
Bochum, Germany, Notified body number: 0158
1
2
3
45
6

Ultra Elite Full Face Mask – Positive Pressure 8
Use
GB
3Use
The mask is either carried using the harness in front of the chest or in the mask container.
In order to protect the inside of the mask from dirt, the harness hook is engaged in the front buckle
when the mask is held in front of the chest.
WARNING!
Ensure that the top of the mask seal only lies on the user's forehead. Hair should not be between the
mask's seal and the user’s skin.
The mask could otherwise leak. This danger also exists for instance for mask wearers with beards or
deep scars in the sealing area.
3.1 Donning the Mask
WARNING!
In order to guarantee a proper fit for those wearing glasses, the Ultra Elite Full Face Mask spectacle
kit must be worn since ordinary glasses cannot be worn under the mask.
(1) Spread the harness with both hands.
(2) Position the chin into the chin cup.
(3) Pull the head straps over your head.
Whilst doing so, ensure that the harness is sitting
correctly and not twisted.
(4) If necessary adjust mask and tighten the straps in order
as shown firmly and evenly.
When tightening the head straps ensure that the correct
sequence is followed [Figure Pos. 1 - 3, for EZ harness
Pos. 1].
When using the EZ harness if necessary readjust the
head plate by pulling the loop at the back of the head.
1
3
22
1

Ultra Elite Full Face Mask – Positive Pressure 9
Use
GB
3.2 Leak Check
In order to check the mask-to-face tightness a leak test must be performed before each use.
3.3 Removing the Mask
(1) Seal the mask connector or the inlet opening side of an
attached filter with the ball of your hand.
(2) Test tightness by inhaling and exhaling. Whilst doing so:
when inhaling there must be negative pressure, no
inflowing air should be noticeable.
(3) If necessary retighten the straps.
If the leak test fails the mask must not be used.
(1) Loosen the head harness, press the buckles forwards
using your thumbs.
Do not grip the mask by the exhalation valve!
(2) Grip the mask by the connector and pull off backwards
over your head.

Ultra Elite Full Face Mask – Positive Pressure 10
Cleaning, Disinfection
GB
4 Cleaning, Disinfection
The cleaning and disinfection of the masks is performed in accordance with the cleaning intervals
chapter 5.2.
There are three possible kinds of cleaning:
• Using a washing machine
• disk washing type (Meiko)
• tumbling type (Miele)
• Using an ultrasonic cleaner
• Cleaning by hand.
WARNING!
Do not use cleaning products containing hydrocarbons or solvents [e.g. nitro-thinner].
Cleaned parts must not be dried in radiant heat [sun, radiators]. When using a drying cabinet, the
temperature must not exceed +60°C.
Perform a tightness test after every cleaning, disinfection and maintenance or after every exchange of
parts.
4.1 Cleaning/Disinfection with a Washing Machine
(1) After cleaning check the two screws for the lens ring. Retighten the screws hand-tight if neces-
sary.
4.2 Cleaning/Disinfection with an Ultrasonic Cleaner
Follow the washing agent’s user instructions on this CD/DVD.
When cleaning/disinfecting with an ultrasonic cleaner please follow the cleaning agent’s
user instructions on this CD/DVD.

Ultra Elite Full Face Mask – Positive Pressure 11
Cleaning, Disinfection
GB
4.3 Cleaning by Hand
(1) Remove inhalation and exhalation valve discs.
(2) Unbutton the nose cup.
(3) Unscrew the speaking diaphragm with the special tool.
(4) Clean mask using lukewarm water and mild cleaning agent EW 80 and thoroughly rinse in
running water.
(5) Disinfect the mask after cleaning. Removed components must be separately cleaned and disin-
fected.
(6) Dry mask and components and reassemble mask in reverse order.
(7) Perform a tightness test [chapter 5.5].
4.4 Disinfection by Hand
(1) Disassemble and clean the mask (see chapter 4.3).
(2) Disinfect the mask using recommended disinfectant. Please observe the user instruction for the
disinfectant.
(3) Thoroughly rinse mask in running water.
(4) Dry mask and components and reassemble mask in reverse order.
(5) Perform a tightness test (see chapter 5.5).
Clean the mask before disinfecting.
Use a disinfectant according to the user instructions on this CD/DVD.

Ultra Elite Full Face Mask – Positive Pressure 12
Maintenance
GB
5 Maintenance
5.1 Maintenance Instructions
This device should be regularly checked and serviced by trained specialists. Inspection and service
records must be maintained. Always use original parts from MSA.
Repairs and maintenance must be carried out only by authorised service centres or by MSA. Changes
to devices or components are not permitted and will result in loss of approval.
MSA is liable only for maintenance and repairs carried out by MSA.
5.2 Maintenance Intervals
*) For a 2-year interval cleaned and disinfected masks have to be stored airtight. Otherwise masks
should be cleaned and disinfected at least semi-annually. After each cleaning and disinfection the
facepiece must be checked.
**) For airtightly packed facepieces, which are not exposed to increased climatic and mechanical stress
[for example transport on vehicles], this interval can be extended to 2 years.
***) Only applicable for PS and PS-ESA
MSA recommends the following maintenance intervals. If necessary considering the
usage, tasks may be at even shorter intervals than indicated.
Observe national laws and regulations!
If in any doubt, ask your local MSA contact person.
Work to be
Performed
Maximal Intervals
Before use After Use 6-monthly Two
years
Four
years
Six
years
Cleaning and Disin-
fection*) XX
*)
Visual, Functional
and Tightness
Check **)
XX
**)
Replacement of the
exhalation valve
disc
X
Replacement of the
Speech Diaphragm X
Replacement of the
O-ring for connector XX
***)
User check X

Ultra Elite Full Face Mask – Positive Pressure 13
Maintenance
GB
5.3 Maintenance of the Exhalation Valve
In case of a leak remove the exhalation valve disc and replace it with a new one as follows:
(1) Open the pivot cap of the connector.
(2) Carefully remove the spring retainer with spring.
(3) Pull of valve disc with guide pin.
(4) Replace valve disc with pin and reassemble mask in reverse order.
(5) Close the pivot cap of the connector.
(6) Perform a tightness test [chapter 5.5].
5.4 Replacing the Speech Diaphragm
(1) Unbutton the nose cup.
(2) Unscrew the threaded socket from the mask inside with the special tool.
(3) Remove the speech diaphragm.
(4) Assemble the new speech diaphragm with the gasket towards the connector.
(5) Perform a tightness test [chapter 5.5].
5.5 Tightness Test of the Mask
(1) Fit mask tight onto the test instrument.
(2) Generate a negative pressure of 10 mbar.
(3) Measure the pressure change after 1 min.
The mask including the exhalation valve meets the requirements if for a moistened exhala-
tion valve and a negative pressure generated inside the mask the pressure change does not
exceed 1 mbar in a minute.
Leaking masks must not be used.
Opening Pressure Test of the exhalation valve
The opening pressure of the exhalation valve has to be at least 4.2 mbar, otherwise the mask must not
be used.
The year of manufacture is located on the valve disc.
The year of manufacture is located on the speech diaphragm.
The testing of the masks for tightness is performed using an applicable MSA test device
in accordance with the relevant operating manual.

Ultra Elite Full Face Mask – Positive Pressure 14
Safekeeping and Storage
GB
5.6 Visual Test and Function Test
Visual Test
(1) Inspect the mask for possible damages like for example deformations, stickings or cracks. Valve
discs, especially exhalation valve discs, are crucial functional elements of the mask.
(2) Defective or damaged parts have to be replaced immediately.
Functional Test
After assembling the mask the mobile parts, especially the valve discs, have to be tested for unre-
stricted mobility.
6 Safekeeping and Storage
WARNING!
In order to avoid damage to or the deformation of the masks keep no additional loose objects in the
mask container.
For the safekeeping of the mask the mask container should be used. This also applies to masks with
installed filters, except CO and NO filters.
MSA rubber products are protected by an anti-aging agent that can become visible as a light coating.
This coating is harmless and can be removed during cleaning.
To ensure a long life for rubber components, keep them in a cool, dry place that is protected from ultra-
violet radiation, according to ISO 2230:2002, Rubber Products – Guidelines for Storage.

Ultra Elite Full Face Mask – Positive Pressure 15
Ordering Information
GB
7 Ordering Information
7.1 Exploded View
Fig. 3 Full face mask exploded view
1
2
3
22
4
5
212019
18
14
12
11
10
9
15
16
17
678
13
1 Nose cup valve seat 12 Valve assembly P
2 Nose cup valve disc 13 Cover P, Elite
3 Nose cup [without valves] 14 Clamp
4 Head harness 15 Inhalation valve seat Elite
5 Carrying strap 16 Inhalation valve disc
6 AutoMaXX connector Ultra Elite 17 Connector, Elite
7 ESA connector [assembly with O-Ring] 18 Lens ring
8 PS connector [assembly with O-Ring] 19 Screw for lens ring
9 Speech diaphragm ring 20 Lens
10 Speech diaphragm 21 Face blank
11 Exhalation valve disc 22 Buckles, Elite

Ultra Elite Full Face Mask – Positive Pressure 16
Ordering Information
GB
7.2 Full Face Mask
Description Article No.
Standard Thread Connector M45 x 3
Ultra Elite PF D2056741
Ultra Elite PF – small D2056785
Ultra Elite PF – silicone D2056763
Ultra Elite PF-EZ D2056771
Ultra Elite PF-EZ – small D2056781
MSA Plug-in Connector
Ultra Elite PS D2056751
Ultra Elite PS – small D2056789
Ultra Elite PS – silicone D2056764
Ultra Elite PS-EZ D2056772
Ultra Elite PS-EZ – small D2056782
Ultra Elite PS Transponder 10026552
AutoMaXX Plug-in Connector
Ultra Elite PS-MaXX 10031385
Ultra Elite PS-MaXX – small 10031383
Ultra Elite PS-MaXX – silicone 10031384
Ultra Elite PS-MaXX-EZ 10031382
Ultra Elite PS-MaXX-EZ – small 10031381
Ultra Elite PS-MaXX Transponder 10069782
Ultra Elite PS-MaXX – small Transponder 10099996
Ultra Elite PS-MaXX – silicone Transponder 10070554
Ultra Elite PS-MaXX – large Transponder 10100876
ESA Plug-in Connector
Ultra Elite PF-ESA 10031393
Ultra Elite PF-ESA – small 10031392
Ultra Elite PF-ESA – silicone 10031396
Ultra Elite PF-ESA-EZ 10031391
Ultra Elite-PF-ESA-EZ – small 10031390

Ultra Elite Full Face Mask – Positive Pressure 17
Ordering Information
GB
7.3 Accessories
7.4 Replacement Parts
Description Article No.
Elite spectacles [plastic frame] D2056730
Elite spectacles [metal frame] D2056733
Special tool [for replacing exhalation valve and speech diaphragm] D2055038
Exhalation valve closure D2056703
Mask hanger [package of 4] D2055753
Mask tightness test kit [for more MSA testing instruments refer to
www.msa.europe.com] D6063705
Carrying bag Elite D2055400
Carrying container Elite D2056734
Leak test adapter M45 x 3 D4074847
Leak test adapter [for quick-connect coupling] D4074890
Adapter thread 40 x 1/7 inch to quick-connect coupling
[filter adapter for masks with quick-connect coupling] D1070712
Description Article No.
Service kit Elite P
[inhalation valve, exhalation valve, valve seat, 2 nose cup valve discs] D2056706
Nose cup Elite, assembly D2056915
Lens Elite [polycarbonate with silicate coating] D2056802
Lens ring Elite, assembly D2056705
Clamp Elite D2056717
Speech diaphragm [package of 2] D2055708
Nose cup valve seat [package of 2] D2056708
Nose cup valve disc [package of 20] D2055731
Inhalation valve disc P [package of 20] D2056722
Inhalation valve seat P [package of 5] D2056723
Exhalation valve disc P [package of 10] D2056724
Head harness [rubber] 10102911
Head harness [silicone] D2055219-SP
Buckle with hook [package of 5] D2056712
Carrying strap, assembly D2055707-SP
Connector P Elite, assembly D2056720
Connector PS, assembly D2056727
Connector ESA 10037519
Connector AutoMaXX 10032072
O-Ring for quick connect adapter, 10 pcs 10145638
Quick-connect coupling AutoMaXX / Ultra Elite 10145637

For local MSA contacts, please visit us at MSAsafety.com
Because every life has a purpose...