multicomp pro MP780522 User manual

Digital Tachometer
MP780522

Please read these instructions carefully before use and retain for future reference.
• To avoid injuries to animal or human eyes, Please do not point the laser beam in eyes
or look directly into beam.
• There are no user-serviceable parts in this product. Refer servicing to qualied
personnel.
• Never operate the meter with the cover removed or the battery door open.
• Remove dead batteries from the meter or if it is not going to be used for a long time.
• Never mix old and new batteries together, or different types of batteries.
• Never dispose of batteries in a re, or attempt to recharge ordinary batteries.
SAFETY INFORMATION
FEATURES
WHATS INCLUDED
• This Digital Tachometer provides fast and accurate non-contact RPM and surface
speed measurements of rotating objects.
• *This tachometer is used the CPU technique, photo-electrical technique, and junction
laser technique for one instrument combined PHOTO TACH. (RPM & REV)
• Two test modes: rotate speed mode (unit: RPM) & count mode (unit: REV)
• Wide measure range and high resolution.
• High visible digital LCD and backlight display.
• Built-in memory recalls Max/Min and last value stored.
• Tachometer
• Instructions
• Carrying case
• 3 x Reective tapes
Memory Button
Measure Button
Mode Button
LCD Display
Laser Lens

OPERATION
MAINTENANCE
• Cut the reective adhesive tap provide into approx 12mm (0.5″) squares and apply one
square to each rotation shaft.
NOTE: The non-reective area must always be greater than the reective area.
• If the shaft is normally reective, it must be covered with black tape or black paint
before attaching reective tape
• The shaft surface must be clean and smooth before applying reective tape.
• Depress the “MEAS” button and align the visible light beam with the applied target
• Verify that monitor indicator lights when the target aligns with the beam.
• The current mode is the last time mode used. If you need to change the mode, release
the “MEAS” button and press the “MODE” button before the instrument auto powers off
to switch between “RPM” and “REV” (revolution).
• Select the mode of you require, then press the “MEAS” to start readings.
NOTE: This instrument will auto power off in 10 sec after releasing the “MEAS” button.
• Press the “MEM” button displays the reading of the Max, Min and Last value for the
previous measurement taken.
VERY LOW RPM MEASUREMENT
• Measuring high resolution and fast sampling time is easier than measuring slow RPM.
• If measuring very low RPM values, it is suggested to attach more “REFLECTIVE
MARKS” spaced around the shaft
• Then divide the reading shown by the number of “REFLECTIVE MARKS” placed to get
the correct RPM value.
Replacing the battery
• When the meter display fades the battery needs changing.
• Open the battery cover on the rear case.
• Remove the old battery and t a new 9V PPA battery into the battery holder noting the
correct polarity of the connector.
• Replace the battery cover.
Cleaning
• Clean the meter with a clean, soft cloth.
• Do not use any chemicals, abrasives or solvents that could damage the meter.

SPECIFICATIONS
Display: Large 5 digit LCD
Non-contact test range: 2 to 99,999 RPM
Tot test range: 0 to 99,999 RPM
Accuracy: ±(0.05% + 1digit)
Resolution: 0.1RPM (2 to 9999.9RPM) / 1RPM (over 10000 RPM)
Sampling time: 0.5 sec.(over 120 RPM)
Detecting distance: 50mm to 500mm
Memory: Built-in memory recalls Max/Min/Last
Time base: Quartz crystal
Power consumption: Approx.45mA
Battery: 9V battery or 6VDC via PSU
Dimensions: 160 x 60 x 42mm
Weight: 150g approx
Operation temp: 0o to 50o (32o to 122o)
INFORMATION ON WASTE DISPOSAL FOR CONSUMERS OF
ELECTRICAL & ELECTRONIC EQUIPMENT
These symbols indicate that separate collection of Waste Electrical and Electronic Equipment
(WEEE) or waste batteries is required. Do not dispose of these items with general household
waste. Separate for the treatment, recovery and recycling of the materials used. Waste batteries
can be returned to any waste battery recycling point which are provided by most battery retailers.
Contact your local authority for details of the battery and WEEE recycling schemes available in
your area. Made in China. LS12 2QQ
Man Rev 1.0