manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. multicomp pro
  6. •
  7. Measuring Instrument
  8. •
  9. multicomp pro MP760861 User manual

multicomp pro MP760861 User manual

CLAMP METER, 400A, 600V, 30MM
MP760861
Safety
International Safety Symbols
This symbol, adjacent to another symbol or terminal, indicates the user must refer
to the manual for further information.
This symbol, adjacent to a terminal, indicates that, under normal use, hazardous
voltages may be present
Double insulation
SAFETY NOTES
Do not exceed the maximum allowable input range of any function
Do not apply voltage to meter when resistance function is selected.
Set the function switch OFF when the meter is not in use.
WARNINGS
Set function switch to the appropriate position before measuring.
When measuring volts do not switch to current/resistance modes.
When changing ranges using the selector switch always disconnect the test leads from
the circuit under test.
Do not exceed the maximum rated input limits.
CAUTIONS
Improper use of this meter can cause damage, shock, injury or death. Read and understand
this user manual before operating the meter.
Always remove the test leads before replacing the battery.
Inspect the condition of the test leads and the meter itself for any damage before operating
the meter. Repair or replace any damage before use.
Use great care when making measurements if the voltages are greater than 25VAC rms or
35VDC. These voltages are considered a shock hazard.
Remove the battery if the meter is to be stored for long periods.
Always discharge capacitors and remove power from the device under test before
performing Diode, Resistance or Continuity tests.
Voltage checks on electrical outlets can be difficult and misleading because of the
uncertainty of connection to the recessed electrical contacts. Other means should be used
to ensure that the terminals are not "live".
If the equipment is used in a manner not specified by the manufacturer, the protection
provided by the equipment may be impaired.
Input Limits
Function
Maximum Input
A
400A DC/AC
V DC, V AC
600V DC/AC
Frequency, Resistance, Diode, Continuity ,
Capacitance Test
250V DC/AC
Temperature (℃/℉)
250V DC/ AC
Meter Description
1. Current clamp
2. Non-contact AC voltage indicator light
3. Clamp trigger
4. Rotary Function swith
5. Data Hold/ Back Light button
6. Relative button
7. LCD display
8. MODE select button
9. Range button
10. Hz% Hlod button
11. COM input jack
12. V ΩCAP TEMPHz jack
13. Battery Cover
1. AC DC AC (alternating current)
and DC (direct currrent)
2. Minus sign
3. 8.8.8.8 4000 count (0 to 3999)
measurement reading
4. AUTO AutoRange mode
5. REL Relative mode
6. Diode test mode
7. •))) Audible Continuity
8. HOLD Data Hold mode
9. ℃,℉,,m,V,A,K,M,Ω, Units of measure list
10. Hz % Frequency/duty cycle test mode
Specifications
Function
Range & Resolution
Accuracy (% of reading)
AC Current
(50/60Hz)
40.00 AAC
± (2.5 % + 8 digits)
400 .0AAC
± (2.8 % + 5 digits)
DC Current
40.00 ADC
± (2.5 % + 5 digits)
400 .0ADC
± (2.8 % + 5 digits)
DC Voltage
400.0 mVDC
± (0.8% + 2 digits)
4.000 VDC
± (1.5% + 2digits)
40.00 VDC
400.0 VDC
600.0 VDC
± (2 % + 2 digits)
AC Voltage
(50-400Hz)
400.0mVAC
± (1.5% + 30 digits)
4.000 VAC
± (1.5% + 5 digits)
40.00 VAC
400.0 VAC
600.0 VAC
± (2.0% + 5 digits)
Resistance
400.0 Ω
± (1.0% + 4 digits)
4.000KΩ
± (1.5% + 2 digits)
40.00KΩ
400.0KΩ
4.000MΩ
± (2.5% + 3 digits)
40.00MΩ
± (3.5% + 5 digits)
Capacitance
40.00nF
(4.0% reading + 20 digits)
400.0nF
(3% reading + 5 digits)
4.000μF
40.00μF
100.0μF
(5.0% reading + 10 digits)
Frequency
10-10kHz
Sensitivity:100V(<50Hz);50V(50 to
400Hz;15V(401Hz to 10kHz)
(1.5% reading + 2 digits)
Temp
(type-K)
(probe accuracy
not included)
-20.0 to 760.0C
(3%rdg+5C)
-4.0 to1400.0F
(3%rdg+9F)
Clamp size Opening 1.2" (30mm) approx
Diode Test Test current of 0.3mA typical; Open circuit voltage 1.5V DC
typical.
Continuity Check Threshold <150; Test current < 0.5mA
Low Battery Indication “ ” is displayed
Overrange Indication “OL”” is displayed
Measurements Rate 2 per second, nominal
Input Impedance 10M(VDC and VAC)
Display 4000 counts LCD
AC Current 50-60Hz (AAC)
AC Voltage bandwidth 50-400Hz (VAC)
Operating Temperature 41 to 104oF (5 to 40oC)
Storage Temperature -4 to 140oF (-20 to 60oC)
Operating Humidity Max 80% up to 87F (31C) decreasing linearly to 50% at
104F(40C)
Storage Humidity <80%
Operating Altitude 7000ft. (2000meters) maximum.
Over voltage Category III 600V
Battery 1 x 9V Battery
Auto OFF approx. 30 minutes
Dimensions/Weight 197x70x40mm/183g
Safety For indoor use and in accordance with Overvoltage
Category II, Pollution Degree 2. Category II includes local
level, appliance, portable equipment, etc., with transient
overvoltages less than Overvoltage Cat. III
Ω
1
2
3
45
6 7 8
9
10
Operation
NOTICES: Read and understand all warning and precaution statements listed in the
safety section of this operation manual prior to using this meter. Set the function
select switch to the OFF position when the meter is not in use.
AC/DC Current Measurements
WARNING: Ensure that the test leads are
disconnected from the meter before making current
clamp measurements.
1. Set the Function switch to
the 400ADC, 40ADC, 400AAC or 40AAC range.
2. If the range of the measured is not known,
select the higher range first then move to the lower
range if necessary.
3. Press the trigger to open jaw. Fully enclose one conductor
to be measured.
The clamp meter LCD will display the reading.
AC/DC Voltage Measurements
1. Insert the black test lead into the negative COM terminal and the
red test lead into the positive Vterminal.
2. Set the function switch to the Vposition.
3. Select AC or DC with the MODE button.
4. Connect the test leads in parallel to the circuit under test.
5. Read the voltage measurement on the LCD display.
Resistance Measurements
1. Insert the black test lead into the negative COM terminal and the
red test lead into the positive terminal.
2. Set the function switch to the •))) CAP position.
3. Touch the test probe tips across the circuit or component under
test. It is best to disconnect one side of the device under test so
the rest of the circuit will not interfere with the resistance reading.
4. For Resistance tests, read the resistance on the LCD display.
Diode and Continuity Measurements
1. Insert the black test lead banana plug into the negative COM jack and the red test lead
banana plug into the positive diode jack.
2. Turn the rotary switch to the •))) CAP position.
3. Press the MODE button until “ “ appears in the display.
4. Touch the test probes to the diode under test. Forward voltage will indicate 0.4V to 0.7V.
Reverse voltage will indicate “OL”. Shorted devices will indicate near 0mV and an open
device will indicate “OL” in both polarities.
For Continuity tests, if the resistance is < 150Ω, a tone will sound.
Capacitance Measurements
WARNING: To avoid electric shock, disconnect power to the unit under test and
discharge all capacitors before taking any capacitance measurements. Remove the
batteries and unplug the line cords.
1.Set the rotary function switch to the •))) CAP position.
2.Insert the black test lead banana plug into the negative (COM) jack.
Insert the red test lead banana plug into the positive (V) jack.
3.Touch the test leads to the capacitor to be tested.
4.Read the capacitance value in the display
Frequency or % duty cycle measurements
1. Set the rotary function switch to the “VDC/AC,Hz” position.
2. Insert the black lead banana plug into the negative COM jack and the red test lead
banana plug into the positive V jack.
3. Select Hz or % duty with the Hz/% button.
4. Touch the test probe tips to the circuit under test.
5. Read the frequency on the display.
Temperature Measurements
WARNING: To avoid electric shock, disconnect both test probes from any source of
voltage before making a temperature measurement.
1. Set the function switch to ℃or ℉.
2. Insert the Temperature Probe into the negative (COM) and the V jacks, making sure to
observe the correct polarity.
3. Touch the Temperature Probe head to the part whose temperature you wish to
measure. Keep the probe touching the part under test until the reading stabilizes (about
30 seconds).
4. Read the temperature in the display. The digital reading will indicate the proper decimal
point and value.
WARNING: To avoid electric shock, be sure the thermocouple has been removed before
changing to another measurement function
Red Black Black Red
Probe Probe Probe Probe
Forward test Reverse test
Ω
Ω
Non-Contact AC Voltage Measurements
1. Touch the probe tip to the hot conductor or insert into the hot side of the electrical outlet.
2. If AC voltage is present, the detector light will illuminate.
NOTE: The conductors in electrical cord sets are often twisted. For best results, rub the
probe tip along a length of the cord to assure placing the tip in close proximity to
the live conductor.
NOTE: The detector is designed with high sensitivity. Static electricity or other sources of
energy may randomly trip the sensor. This is normal operation
MODE BUTTON
To select DC/ACV,OHM/ Diode/Continuity/CAP
Data Hold Button
To freeze the LCD meter reading, press the data hold button. The data hold button is
located on the left side of the meter (top button). While data hold is active, the HOLD
display icon appears on the LCD. Press the data hold button again to return to normal
operation.
REL BUTTON
For DCA and Capacitance Zero & Offset adjustment.
RANGE BUTTON
When the meter is first turned on, it automatically goes into Auto Ranging. This
automatically selects the best range for the measurements being made and is generally the
best mode for most measurements. For measurement situations requiring that a range be
manually selected, perform the following:
1. Press the RANGE button. The “Auto Range” display indicator will turn off, The “Manual
Range” display indicator will turn on
2. Press the RANGE button to step through the available ranges until you select the range
you want.
3. Press and hold the RANGE button for 2 seconds to exit the Manual Ranging mode and
return to Auto Ranging.
Battery Replacement
1. Remove the screw and lift off the battery cover
2. Replace the 1 x 9V battery noting the polarity
3. Replace the cover and the securing screw before using the meter.
INFORMATION ON WASTE DISPOSAL FOR CONSUMERS OF
ELECTRICAL & ELECTRONIC EQUIPMENT.
When this product has reached the end of its life it must be treated as Waste
Electrical & Electronic Equipment (WEEE). Any WEEE marked products must
not be mixed with general household waste, but kept separate for the
treatment, recovery and recycling of the materials used. Waste batteries can
be returned to any waste battery recycling point which are provided by most
battery retailers. Contact your local authority for details of recycling schemes
in your area.
Made in China.
PO Box 13362 Dublin 2
LS12 2QQ
WARNING: Risk of Electrocution. Before
use, always test the Voltage Detector on a
known live circuit to verify proper operation

Other multicomp pro Measuring Instrument manuals

multicomp pro MP780892 User manual

multicomp pro

multicomp pro MP780892 User manual

multicomp pro MP760862 User manual

multicomp pro

multicomp pro MP760862 User manual

multicomp pro MP760607 User manual

multicomp pro

multicomp pro MP760607 User manual

multicomp pro MP60607 User manual

multicomp pro

multicomp pro MP60607 User manual

multicomp pro MP780905 User manual

multicomp pro

multicomp pro MP780905 User manual

multicomp pro MP700852 User manual

multicomp pro

multicomp pro MP700852 User manual

multicomp pro MP001186 User manual

multicomp pro

multicomp pro MP001186 User manual

multicomp pro MP780896 User manual

multicomp pro

multicomp pro MP780896 User manual

multicomp pro MP700006 User manual

multicomp pro

multicomp pro MP700006 User manual

multicomp pro MP780647 User manual

multicomp pro

multicomp pro MP780647 User manual

multicomp pro MP780117 User manual

multicomp pro

multicomp pro MP780117 User manual

multicomp pro MP780002 User manual

multicomp pro

multicomp pro MP780002 User manual

multicomp pro MP780904 User manual

multicomp pro

multicomp pro MP780904 User manual

multicomp pro MP780966 User manual

multicomp pro

multicomp pro MP780966 User manual

multicomp pro MP780119 User manual

multicomp pro

multicomp pro MP780119 User manual

multicomp pro MP005768 User manual

multicomp pro

multicomp pro MP005768 User manual

multicomp pro MP780522 User manual

multicomp pro

multicomp pro MP780522 User manual

multicomp pro MP780859 User manual

multicomp pro

multicomp pro MP780859 User manual

multicomp pro MP770291 User manual

multicomp pro

multicomp pro MP770291 User manual

multicomp pro MP780649 User manual

multicomp pro

multicomp pro MP780649 User manual

multicomp pro MP780994 User manual

multicomp pro

multicomp pro MP780994 User manual

multicomp pro MP780118 User manual

multicomp pro

multicomp pro MP780118 User manual

multicomp pro MP700121 User manual

multicomp pro

multicomp pro MP700121 User manual

multicomp pro MP700506 User manual

multicomp pro

multicomp pro MP700506 User manual

Popular Measuring Instrument manuals by other brands

THORLABS S3FC1310 user guide

THORLABS

THORLABS S3FC1310 user guide

Purkay Labs AUDIT-BUDDY Gen 2 user manual

Purkay Labs

Purkay Labs AUDIT-BUDDY Gen 2 user manual

Simrad PI TRAWL HYDROPHONE - INSTALLATION REV B installation manual

Simrad

Simrad PI TRAWL HYDROPHONE - INSTALLATION REV B installation manual

PeakTech 1640 Operation manual

PeakTech

PeakTech 1640 Operation manual

PCB Piezotronics IMI SENSORS 602M42 Installation and operating manual

PCB Piezotronics

PCB Piezotronics IMI SENSORS 602M42 Installation and operating manual

Atlanta ASF 2045 user manual

Atlanta

Atlanta ASF 2045 user manual

Instantel Blastmate III Operator's manual

Instantel

Instantel Blastmate III Operator's manual

SDI Solutions simple SDI Operator's manual

SDI Solutions

SDI Solutions simple SDI Operator's manual

Hanna Instruments HI 93711 instruction manual

Hanna Instruments

Hanna Instruments HI 93711 instruction manual

OrienTek T11P Instructions for use

OrienTek

OrienTek T11P Instructions for use

sebaKMT Correlux C-3 user manual

sebaKMT

sebaKMT Correlux C-3 user manual

Bante Instruments 210 user manual

Bante Instruments

Bante Instruments 210 user manual

Bosch 200 C Original instructions

Bosch

Bosch 200 C Original instructions

Movacolor MC-12 user manual

Movacolor

Movacolor MC-12 user manual

Cobolt Skyra Cobolt MLD 405 nm owner's manual

Cobolt

Cobolt Skyra Cobolt MLD 405 nm owner's manual

Knick Protos PH 3400(X)-033 user manual

Knick

Knick Protos PH 3400(X)-033 user manual

Kkmoon GM8805 instruction manual

Kkmoon

Kkmoon GM8805 instruction manual

Vega FiberFlex LFXG-H operating instructions

Vega

Vega FiberFlex LFXG-H operating instructions

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.