MULTISPAN PIC-4202 User manual

All digit segment will be turned ON for 3 sec
Process Value
Set Value
   

1) Press Key to enter in parameter menu.
2) Press Key to go to next parameter.
4) Press Key to save change in setting
3) Use Or key to change value of parameter.
-999 To 9999 Selectable
2 Relay 1C/O
24V DC
Output
Transmitter
Supply
Power Supply 100 to 250V AC (SMPS)
Model
Display
Size
Panel Cutout
Input
Range
44 X 44
48 X 48 X 95
UPPER:- 4 Digit 7 seg .39”,red LED Display
LOWER:- 4 Digit 7 seg .28”,green LED Display
PIC-4202
0 To 10V DC,4 To 20mA DC,0 To 20mA DC
OPERATING MANUAL
PROCESS CONTROLLER
www.multispanindia.com
Page - 1
PIC-4202
PIC-4202
Technical Specification
Key Operations
PIC 4202


R1
R2

www.multispanindia.com
Page - 2
USER CONFIGURATION
Set Value
Set Point 1
Set Point 2
Input Selection
0-10V DC/4-20mA DC/0-20 mA DC









Press key for 3 sec to
enter Password parameter
 Process Value
Power ON


Hystersis-1 For set point-1
Range: 0 To 1000
Range: 0 To 1000
Hystersis-2 For set point-2
Mode-1
Mode-2
Decimal Point
Range: 00.00/0.000/0000
Low Range
High Range
Range: -999 TO 9999
Range: -999 TO 9999
Range: 1 To 10 Second
High Alarm,Low Alarm,Inband,Outband,
Absoult Low, Absoult outband Alarm For 1 relay
High Alarm,Low Alarm,Inband,Outband,
Absoult Low, Absoult outband Alarm For 2 relay









 .


Filter Time


Off-Set


st
nd
Range : -100 To +100 Count
Press key
Press key
Press key
Press key
Press key
Press key
Press key
Press key
Press key
Press key
Press key
Press key
Press key

Correction Factor
Signal Low Lavel
if input 4 to 20mA is selected then




Range: -25 To +25 Count
Ampere Range: 0 To 5mA
Press key for Save & Exit
Press key
Press key
Working
1). Do all connection as shown in connection diagram and turn on the instrument.
2). Display will indicates process value according to 4-20mA input available and according
to decimal point.
3). The Range Corresponding to 4-20mA is selectable from keypad.
4). If high range is to select 9999 then at 20mA input the display will show 9999
& if low range is to select 0000 then at 4mA input the display will show 0000.
5).
6). In High Alarm (For Mode-1),Initially relay-1 will be off condition. When Process value
equals set point-1 relay-1 will turn on. When process value equal set 1- Hys 1 then
again relay-1 will be off.
7).
11). If the input is not connected Display will show OPEN.
12). When Input Exceeds the full scale Range (Approx above 20mA) then Display will show
(OVER).
13). When input is lower than 4mA (Signal Low Level Range: 0 To5mA) then Display will show
(LOW).
In Low Alarm (For Mode-1),Initially relay-1 will be on condition. When Process value
equals (Set-1 + Hys-1) relay-1 will turn off. When process value equal set point-1 then
again relay-1 will be on.
In Band Alarm (For Mode-1),Relay-1 will be on between Set point-1 & Set point-2 condition.
8). Out Band Alarm (For Mode-1),Relay-1 will be off between Set point-1 & Set point-2 condition.
9). Absolute Low Alarm (For Mode-1), Initially Relay-1 will be off. When first time process value
equals (Set-1 + Hys-1) then relay-1 will be on. Again process value below Set point-1 relay
remains on.
10). Absolute Out Band Alarm, Initially relay will be off. When first time process value is in between
Set point-1 & Set point-2 relay will be on. Now, Process value is below Set point-2 & Above
Set point-1 relay remains off.


www.multispanindia.com
Page - 3

Product improvement and upgrade is a constant procedure. So for more updated operating information and support, please
contact our Helpline : [phone]/75 or Email at [e-mail] www.multispanindia.com
Page - 4
Connection Diagram
N
L
CC R1
R2
+
-
24V DC
NONO
NC