MULTISPAN UTC-3203 User manual

UTC-3203
www.multispanindia.comPage - 2
All safety related codifications, symbols and instructions that appear in this operating manual
or on the equipment must be strictly followed to ensure the safety of the operating personnel as
well as the instrument.
If all the equipment is not handled in a manner specified by the manufacturer, it might impair the
protection provided by the equipment .
Product improvement and upgrade is a constant procedure. So for more updated operating information and support,
Please contact our helpline : [phone]/76/82 or Email at [email protected] Ver: 06-2017
=> Read complete instructions prior to installation and operation of the unit.
WARNING : Risk of electric shock.
3) Cable used for connection to power source, must have a cross section of 1mm or greater. These wires
should have insulations capacity made of at least 1.5kV.
2) To reduce electro magnetic interference, use wire with adequate rating and twists of the same of
equal size shall be made with shortest connection.
4) When extending the thermocouple lead wires, always use thermocouple compensation wires for wiring
for the RTD type, use a wiring material with a small lead resistance (5Ω max per line)and no resistance
differentials among three wires should be present.
1) To prevent the risk of electric shock power supply to the equipment must be kept OFF while doing the
wiring arrangement. Do not touch the terminals while power is being supplied.
5) A better anti-noise effect can be expected by using standard power supply cable for
the instrument.
1) This equipment, being built-in-type, normally becomes a part of main control panel and in such case the
terminals do not remain accessible to the end user after installation and internal wiring.
2) Do not allow pieces of metal, wire clippings, or fine metallic fillings from installation to enter the product
or else it may lead to a safety hazard that may in turn endanger life or cause electrical shock to the operator.
3) Circuit breaker or mains switch must be installed between power source and supply terminal to
facilitate power ‘ON’ or ‘OFF’ function. However this mains switch or circuit breaker must be
installed at convenient place normally accessible to the operator.
4) Use and store the instrument within the specified ambient temperature and humidity ranges as
mentioned in this manual.
Warning Guidelines
Installation Guidelines
Mechanical Installation
Maintenance
Safety Precautions
1) Prepare the panel cutout with proper dimensions as show above.
2) Fit the unit into the panel with the help of clamp given.
3) The equipment in its installed state must not come in close proximity to any heating source,
caustic vapors, oils steam, or other unwanted process by products.
4) Use the specified size of crimp terminal (M3.5 screws) to wire the terminal block. Tightening the
screws on the terminal block using the tightening torque of the range of 1.2 N.m.
5) Do not connect anything to unused terminals.
1) The equipment should be cleaned regularly to avoid blockage of ventilating parts.
2) Clean the equipment with a clean soft cloth. Do not use isopropyl alcohol or any
other cleaning agent.
3) Fusible resistor must not be replaced by operator.
2
A
B
MODEL A
96mm 48mm 44mm 92mm 6mm 85mm
BC
D E F
DIMENSIONS
120mm - 4.72 inches
60mm - 2.36 inches
F
E
C
D
°C
ENT
UTC 3203
°C
R1
R2
R3
1 2 3 4
1 2 3 4
www.multispanindia.com
Page - 1
UTC-3203
Connection Diagram
OPERATING MANUAL
UNIVERSAL TEMPERATURE CONTROLLER
UTC-3203
Note:
1) If sensor connection is reversed, display will show “SRE” message.
2) If sensor is not connected, display will show Open message.
3) Every time the instrument is turned ON, following pattern will be displayed
POWER ON
j
0 1 2 3
0 1 2 3
I N P t
8888
88
8
8
All digit segment will be turned ON for 3 sec
Previous or default sensor input will be displayed for 2 sec
Process Value
Set Value
J: 0 to 600°C / K: 0 to 1200°C /
PT-100: -99 to 400ºC, PT.1: -99.0 to 400.0°C
TP/PID/ ON-OFF (selectable)
Output
Power Supply
Operating
Temperature
Relative
Humidity
100 to 250V AC,50/60 Hz, Approx 4VA
0°C To 55°C
Up to 95% RH Non Condensing
Model
Display
Size (mm)
Panel Cutout
Input
Temperature
Range
Control Action
96 (H) X 48 (W) X 85 (D) mm
92 X 44 mm
UTC-3203
J, K, PT-100
3Relay, 1C/O Contact, 5A,230V AC,
Technical Specification
Protection
Level
(As per request)
IS/IEC 60529 : 2001
IP-65 (Front side) As per
UPPER:- 4 Digit 7 seg 0.39”, red LED Display
LOWER:- 4 Digit 7 seg 0.28”, green LED Display
°C
ENT
UTC 3203
°C
R1
R2
R3
1 2 3 4
1 2 3 4
NO
C
R3
NC
!
L
N
RTD
100
250V AC
~
50/60 Hz,4VA
NO
NO
C
C
R1
R2
NC
NC
T/C
-
-
-

Off-set correction
1 to 999 Sec 1 to 999 Sec
-20.0°C to +20.0°C
-20°C to +20°C
Delay Time 1 To 3
CT 4 sec to 99 sec 4 sec to 99 sec
IT
000 to 9999
000 to 9999
Hysteresis 1 To 3 0.1°C to 50.0°C
1°C to 50°C
MR
PB
-9.0 to +9.0
2.0 to 20.0
-9 to +9
2 to 20
DT 000 to 9999 000 to 9999
PB
Sr.
1
2
3
4
5
6
7
8
9
000 to 999.9 000 to 999.9
Parameter Range for PT.1 sensor
Range for J, K, PT100
Factory Setting
FACTORY SETTING
PARAMETER
IT
CT ( For PID)
PB
OFFSET
TIME-1
TIME-2
PB
DT
MR
HYSTERESIS-1
HYSTERESIS-2
HYSTERESIS-3
VALUES
300
15 SEC.
20.0
75
0°C
5°C
08
0°C
3°C
3°C
3°C
6 SEC
6 SEC
SR.
2
4
CT
6
1
3
5
7
8
9
10
11
12
13
ENT
ENT
yes : press key to apply factory set
values as shown in table.
nO : press key to escape
from factory setting.
Press + key
for 3 sec
IF T1MD=OFF
IF T2MD=OFF
IF 3MD=OFF
IF R1MD=OFF
IF R2MD=OFF
IF R2MD=OFF
www.multispanindia.com
Page - 3
Set Value
Set Point-1
Set Point-2
Set Point-3
Password Message
Press key for 3 sec to
enter Password
SET
Process Value
Input ( J / K / Pt.1 / Pt100 )
Control Action (PID/ON-OFF/TP)
Password Message
P TP T. 1
T P
O N O F
K
SET
SET SET SET
Press key
ENT
Set Point Low Limit
Set Point High Limit
HEAT, COOL, H-AL, AB-L
L-AL, I-AL, O-AL, OFF, AB-O
HEAT, COOL, H-AL, AB-L, AB-O
L-AL, O-AL, I-AL, E-AL, OFF
HEAT, COOL, H-AL, AB-L, AB-O
L-AL, O-AL, I-AL, E-AL, OFF
OFF-SET
TO ENTER BASIC
CONFIGURATION
SETTING, ENTER “73”
www.multispanindia.com
Page - 4
Password Message
IF PID SELECTED IF ON-OFF SELECTED IF TP SELECTED
SET
TO ENTER CONTROL
PARAMETER
SETTING, ENTER “37”
6) Orange color LED glows during auto tuning mode.
1) Press key to go parameter setting.
SET
3) Press key to save change in setting
ENT
4) Press key for 6 sec to start/stop PID AUTO TUNING
5) Press + key for 3 sec to go to factory setting mode.
2) Press or key to change value or to select option.
Basic Configuration
Set Point Setting
Control Parameter
Key Operation
UTC-3203 UTC-3203
34
100
set1
100
set2
105
set3
110
pass
50
pass
73
PID ONOF TP
PARA PARA PARA
pass
37
1234
1 3
2 4
fCST
e
Y s
fCST
O
n
INPT
j
CTRL
PID
Pb
20.0
HYS1
3
PB
4
TIM1
6
CT
12
HYS2
3
HYS3
3
MR
0
HYS2
3
HYS3
3
TIM2
6
TIM3
6
TIM1
6
TIM2
6
TIM3
6
OFST
0
It
300
SLL
0
DT
75
TIM1
6
SHL
R1MD
tIUT
t2md
t3md
tIMD
r2md
r3md
t2ut
t3ut
CT
hys2
hys3
MR
TIM2
TIM3
600
HEAT
HOUR
almt
almt
SOhT
E-AL
E-AL
E-AL
MIN
15
3
3
0
6
6
Press key to
Save & Exit
ENT
Press key to Save & Exit
ENT
Press key to Save & Exit
ENT
Press key
SET
Press key
SET
Press key
SET
Press key
SET
Manual Reset
Proportional
Band
Integral
Time
Derivative
Time
Cycle Time
PID
Parameters ON-OFF
Parameters
TP
Parameters
Hysteresis
IF T1MD = SOAK
or SKPS or SKRG
IF T2MD = OFF
IF T2MD = OFF
IF R2MD = OFF
IF R2MD = OFF
or E-AL
or E-AL
IF R1MD = OFF
IF T2MD = OFF
IF T3MD = OFF
or E-AL
IF R2MD = OFF
or E-AL
IF R3MD = OFF
IF T1MD = OFF
IF T1MD = SOAK
or SKPS or SKRG
or E-AL
or E-AL
IF R2MD = OFF
IF R3MD = OFF
IF T3MD = OFF
IF T2MD = OFF
ONDL,SOKT,SKPS,SKRG,ALMT,OFF
SEC/MIN/HOUR
SEC/MIN/HOUR
SEC/MIN/HOUR
SOKT,SKRG,SKPS,ALMT,ONDL,OFF
SOKT,SKRG,SKPS,ALMT,ONDL,OFF
PID AUTO-TUNING
Press key for 6 sec to start/stop
PID auto-tunning
PV
SV
1
234
1234
IF RELATIVE (-50°C To +50°C)
IF RELATIVE (-50°C To +50°C)
s2md
s3md
end
indu
indu
NO
Press key
SET
IF R1/R2 MD=OFF
Save / No
INDIVIDUAL/RELATIVE
INDIVIDUAL/RELATIVE
Press key to Save & Exit
ENT
Press key to input setting
SET