Multistore EXC-750H1 User manual

Assembly InstructIons
eXeCutIve rAnge
PACKS
2
HAngIng
rAIL
1
Jumbo
DrAWer
1
2000H x 750W x 450D
WHITE #2669934 LIgHT Oak #2683480 Dark COCO #2683518
eXC-750H1

ASSEMBLY INSTRUCTION FOR EXC-750H1

When aaching unit to wall put safety bracket in
middle of unit with 5/8 pan screw then 25mm pan
head screw into wall. For plasterboard without a
stud it is recommended to use a plug with screw
(not provided).
PARTS IDENTIFICATION LIST

2 x TOP GABLES
2 x BOTTOM GABLES
2 x FIXED SHELF
1 x 717 30mm HANGING RAIL
1 x BOTTOM KICK
1 x CAM SHELF
   
1CONFIRMAT SCREWS 14
2CAPS 14
3DOWELS 4
4BACKING NAILS 75
5RAIL FLANGES 2
   
6WHITE CAMS 4
7CAM PINS 4
85/8 PAN HEAD UNIT SCREWS 1
925mmPANHEAD WALL SCREWS 1
10 “L” SAFETY BRACKET 1
1 x 717mm H MOULD
718mm x 445mm x 16mm
718mm x 61 x 16mm
1035mm x 445m x 16mm
966mm x 445m x 16mm
718mm x 445mm x 16mm
975mm x 744 x 3
TOP

2 x BACKING BOARDS
BOTTOM
962mm x 744 x 3


RAIL SUPPORT
BRACKETS DOWELS FIXED SHELF KICK




-





-
-


-

“”










INSERT YOUR 4 PINS (7) INTO
THE HOLE NO: (8) PROVIDED.
INSERT THE CAMS INTO THE
HOLES PROVIDED ON THE
BOTTOM OF THE SHELF.
USING SCREW DRIVER TWIST
CAM INTO LOCK POSITION.

1 x DRAWER ASSEMBLY INSTRUCTION

-


-
.
   
6CAMS 2
7CAM PINS 2
830mm 8 GAUGE SCREW 3
9EURO SCREWS 4
10 HANDLE 1
11 RUNNERS PER SET 1
   
1CONFIRMAT SCREWS 4
2DOWELS 4
3BACKING NAILS 20
45/8 X 6 WOOD SCREWS 6
5 INFILL 1
STEP 2.
GRAB YOUR FIRST SIDE AND INSERT YOUR CAMS
INTO THE HOLE PROVIDED ON THE OUTSIDE OF THE
DRAWER GENTLY AS PER INSTRUCTIONS BELOW.
PUSH THE SIDE INTO THE FRONT DOWELS & PIN THEN CAREFULLY USING A SCREW DRIVER TURN
UNTIL IT LOCKS IN. REPEAT THIS PROCESS WITH THE OTHER SIDE.
NOW PLACE YOUR LAST PIECE BETWEEN THE TWO SIDES USING THE
SCREWS NO.1 SUPPLIED SCREW INTO THE SIDES OF THE BACK
DRAWER PIECE.
IMPORTANT NOTICE:
PLACE THE FITTING OVER THE HOLE
KEEPING THE SQUARE EDGE OF THE
FITTING PARALLEL TO THE FACE OF
THE BOARD, KNOCK IN CAREFULLY.









DRAWER ASSEMBLY
C-LEFT-GABLE RUNNER












.


DIAGRAM 1
30. ● ●
29. ● ●
28. ● ●
27. ● ●
26. ● ●
25. ● ●
24. ● ●
23. ● ●
22. ● ●
21. ● ●
20. ● ●
19. ● 5mm HOLES ●
18. ● ●
17. ● ●
15. ● ●
15. ● ●
14. ● ●
13. ● ●
12. ● ●
11. ● ●
10. ● ●
9. ● ●
8. ● ●
7. ● ●
6. ● ●
5. ● ●
4. ● ●
3. ● ●
2. ● ●
1. ● ●
* * *
MAXI ULTRA ‘H’ SERIES
Models Hole Positions CAM PIN-Hole Positions
H1 1 8
HS2 1 8 – 15
H2 1 – 8 13
HS 8
MAXI ULTRA & ULTRA SERIES
Models Hole Positions Models Hole Positions
450 1-6-11-16 LSD550 1-8
315C 1-8-15-20 LSD330 1
515 1-6-11-16-21
Executive 750 ‘H’ SERIES
Models Hole Positions CAM PIN-Hole Positions
HS 8
H1 1 8
H2 1 – 6 11
H3 1 – 8 – 13 20
MAXI & MSM SERIES
Models Hole Positions Fixed Shelf Position
16J3 1 – 8 – 15 22
C16 1 – 8 – 15 – 20 – 25 30
C06 1 – 8 – 15 – 20 – 25 30
600J3 8 – 15 - 22
400J3 1 – 8 – 15
Executive Series
Models Hole Positions Fixed Shelf Position
EXC – 4J 1 – 8 – 15 - 22 N/A
EXC – 5C 1 – 8 – 15 – 20 – 25 N/A
EXC – 4B 8 – 16 – 24 - 32 N/A
EXC – 2B 8 – 14 N/A
EXB - 5C 1 – 8 – 15 – 20 – 25 N/A
EXB – 4J 1 – 8 – 15 – 20 N/A
EXB – 4B 8 – 16 – 22 – 28 N/A
INSTRUCTIONS FOR RUNNER PLACEMENT

Place metal runners in their correct hole posions
(see above DIAGRAM 1) making sure CL = LEFT HAND
GABLE & CR = RIGHT HAND GABLE, then aach using
the special 7.5 euro screws provided.
(see diagram to the right).

multistore.com.au
Multistore Industries (Aust) Pty Ltd
9 Nevilles Street, Underwood QLD 4119 P:[phone] [email protected]
For easy assembly instructions, please refer to video on our website: www.multistore.com.au
Versatile Storage Units
for any room