Multistore MAXI ULTRA-H1 User manual

CLASSIC RANGE
Assembly InstructIons
PACK
1
HAngIng
rAIL
1
Jumbo
DrAWer
1
1495H x 608W x 430D
WHITE #2669937 LIgHT Oak #2683483 Dark COCO #2683521
mAXI uLtrA-H1

ASSEMBLY INSTRUCTION FOR MAXI ULTRA H1
1 x CAM SHELF
2 x FIXED SHELF 1 x BOTTOM KICK
1 x BACK
PARTS IDENTIFICATION LIST

1 x L & R GABLE
When aaching unit to wall put safety bracket in
middle of unit with 16mm pan head screw then
25mm pan head screw into wall. For plasterboard
without a stud it is recommended to use a plug with
screw (not provided).

   
CONFIRMAT SCREWS 50mm x 5mm 
CAPS 
BACKING NAILS 
16mm WOOD SCREW 
 30mm HANGING RAIL 
30mm FLANGES—PER SET OF 2 
   
WHITE CAMS 
CAM PINS 
 16mm PAN HEAD SCREWS 
 25mm PAN HEAD SCREWS 
 “L” SAFETY BRACKET 
FOLD LINE

FOLD OUT THE BACKS, PROCEED TO NAIL INTO
POSITION MAKING SURE YOU ARE SQUARE AT
ALL TIMES.










FIXED SHELF
KICK
TAKE YOUR GABLES AND LAY THEM OUT
FLAT, YOU SHOULD HAVE QTY 2 GABLES
L&R .
NEXT STEP REQUIRES YOU TO OPEN PART 2
AND RETREVE THE INFILL & SCREWS.

USING 30mm 8 GAUGE SCREWS PROVIDED, ATTACH THE INFILL TO THE
FRONT UNDER-SIDE OF THE CAM SHELF BEFORE PUTTING YOUR SHELF
INTO PLACE.
’
--

RAIL SUPPORT
BRACKETS CAM SHELF HOLE 8
INSERT YOUR 4 PINS (9) INTO
THE HOLE NO: (8) PROVIDED.
INSERT THE CAMS INTO THE
HOLES PROVIDED ON THE
BOTTOM OF THE SHELF.
USING SCREW DRIVER TWIST
CAM INTO LOCK POSITION.

1 x DRAWER ASSEMBLY INSTRUCTION

-


-
.
   
6CAMS 2
7CAM PINS 2
830mm 8 GAUGE SCREW 3
9EURO SCREWS 4
10 HANDLE 1
11 RUNNERS PER SET 1
   
1CONFIRMAT SCREWS 4
2DOWELS 4
3BACKING NAILS 20
45/8 X 6 WOOD SCREWS 6
5 INFILL 1
STEP 2.
GRAB YOUR FIRST SIDE AND INSERT YOUR CAMS
INTO THE HOLE PROVIDED ON THE OUTSIDE OF THE
DRAWER GENTLY AS PER INSTRUCTIONS BELOW.
PUSH THE SIDE INTO THE FRONT DOWELS & PIN THEN CAREFULLY USING A SCREW DRIVER TURN
UNTIL IT LOCKS IN. REPEAT THIS PROCESS WITH THE OTHER SIDE.
NOW PLACE YOUR LAST PIECE BETWEEN THE TWO SIDES USING THE
SCREWS NO.1 SUPPLIED SCREW INTO THE SIDES OF THE BACK
DRAWER PIECE.
IMPORTANT NOTICE:
PLACE THE FITTING OVER THE HOLE
KEEPING THE SQUARE EDGE OF THE
FITTING PARALLEL TO THE FACE OF
THE BOARD, KNOCK IN CAREFULLY.









DRAWER ASSEMBLY
C-LEFT-GABLE RUNNER












.



[phone] -



DIAGRAM 1
30. ● ●
29. ● ●
28. ● ●
27. ● ●
26. ● ●
25. ● ●
24. ● ●
23. ● ●
22. ● ●
21. ● ●
20. ● ●
19. ● 5mm HOLES ●
18. ● ●
17. ● ●
15. ● ●
15. ● ●
14. ● ●
13. ● ●
12. ● ●
11. ● ●
10. ● ●
9. ● ●
8. ● ●
7. ● ●
6. ● ●
5. ● ●
4. ● ●
3. ● ●
2. ● ●
1. ● ●
* * *
MAXI ULTRA ‘H’ SERIES
Models Hole Positions CAM PIN-Hole Positions
H1 1 8
HS2 1 8 – 15
H2 1 – 8 13
HS 8
MAXI ULTRA & ULTRA SERIES
Models Hole Positions Models Hole Positions
450 1-6-11-16 LSD550 1-8
315C 1-8-15-20 LSD330 1
515 1-6-11-16-21
Executive 750 ‘H’ SERIES
Models Hole Positions CAM PIN-Hole Positions
HS 8
H1 1 8
H2 1 – 6 11
H3 1 – 8 – 13 20
MAXI & MSM SERIES
Models Hole Positions Fixed Shelf Position
16J3 1 – 8 – 15 22
C16 1 – 8 – 15 – 20 – 25 30
C06 1 – 8 – 15 – 20 – 25 30
600J3 8 – 15 - 22
400J3 1 – 8 – 15
Executive Series
Models Hole Positions Fixed Shelf Position
EXC – 4J 1 – 8 – 15 - 22 N/A
EXC – 5C 1 – 8 – 15 – 20 – 25 N/A
EXC – 4B 8 – 16 – 24 - 32 N/A
EXC – 2B 8 – 14 N/A
EXB - 5C 1 – 8 – 15 – 20 – 25 N/A
EXB – 4J 1 – 8 – 15 – 20 N/A
EXB – 4B 8 – 16 – 22 – 28 N/A
INSTRUCTIONS FOR RUNNER PLACEMENT

Place metal runners in their correct hole posions
(see above DIAGRAM 1) making sure CL = LEFT HAND
GABLE & CR = RIGHT HAND GABLE, then aach using
the special 7.5 euro screws provided.
(see diagram to the right).

multistore.com.au
Multistore Industries (Aust) Pty Ltd
9 Nevilles Street, Underwood QLD 4119 P:[phone] [email protected]
For easy assembly instructions, please refer to video on our website: www.multistore.com.au
Versatile Storage Units
for any room