MUND CLIMA MUPR-H5A User manual

Service manual
English
CL20025 to CL20028
INVERTER SERIE H5A
MUPR-H5A
www.mundoclima.com

3
Product Specification……………………..1
Refrigeration Diagram……...……………..
Wiring Diagram…………………………….
Troubleshooting Guide…………………..
CONTENTS
10
5

1.1 Photo of Product
Chapter 1 Product Specification
Outdoor Unit
Indoor Unit
1

1.2 Outline Dimensions
Indoor Unit
Outdoor Unit (2015-16)
MODEL 9000BTU 12000BTU 18000BTU 24000BTU
Wmm 750 750 900 1082
Dmm 330
Hmm 200 200 225 233
MODEL 9000BTU 12000BTU 18000BTU 24000BTU
Wmm 720 720 802 800
Dmm 260 260 298 300
Hmm 540 540 535 690
285 285 311
Outdoor Unit (2015-16)
MODEL 9000BTU 12000BTU 18000BTU 24000BTU
Wmm 730 730 800 800
Dmm 285 285 315 310
Hmm 545 545 545 690
Outdoor Unit (2017)
2

Steam-gas of low pressure
Liquid of low pressure
(also a little gas)
Gas of high
pressure &
Super cooled liquid temperature
of high pressure
Cooling Mode
Cooling Cycle
Compressor
(Compression)
Outdoor heat exchanger
(Condensation)
Indoor heat exchanger
(Evaporation)
Capillary
(Throttling)
4-way valve
(Heat pump only)
Chapter 2 Refrigeration
D
iagrams
3

Gas of high
Pressure & temperature
Super cooled liquid of low pressure
Steam-gas of
low pressure
Super cooled liquid
of high pressure
Heating Mode
Heating Cycle
Indoor heat exchanger
(Condensation)
Compressor
(Compression)
Capillary
(Throttling)
Outdoor heat exchanger
(Evaporation)
4-way valve
(Heat pump only)
4

Chapter
3
Wiring Diagram
Indoor unit
MUPR-09/12/18/24-H5A
Room temperature (15k)
Pipe temperature (20k)
5

Outdoor unit
L
Orientation Valve
L
EXHAUST PIPE ROOM SWITCH
FAN-DC
W(T/C)
V(S)
U(R)
Compressor
Exhaust
Out pipe Out room
DC Fan Motor
2 2 2 2
S
GND
AC-N
AC-L
4(S)2(N)1(L)
11326007000450
CN-N
CN1
To Indoor Unit
U V W
Brown
Brown
Reactor
Black
Blue
Brown
Y/G
Blue
Black
Red
MUPR-09/12/18-H5A (2015-16)
Out Room temperature (15k)
Out Pipe temperature (20k)
Exhaust (discharge) temperature (50k)
6

Outdoor unit
MUPR-18-H5A (2017)
7

Outdoor unit
MUPR-24-H5A
Out Room temperature (15k)
Out Pipe temperature (20k)
Exhaust (discharge) temperature (50k)
DC Fan motor
8

MUPR-24-H5A(V2)
9

4.1 Error Code
Cha
pter
4
Troubleshooting Guide
Error code COOLING indicator HEATING indicator TIMER indicator Description
E1 1 blink Indoor environment temprature sensor fault
E2 2 blinks Outdoor pipe temprature sensor fault
E3 3 blinks Indoor pipe temprature sensor fault
E4/Fb 4 blinks Indoor fan motor circuit fault
E5/5E 5 blinks Indoor and outdoor communication failure
E8 8 blinks Indoor main P B and display board communication fault
F0 11 blinks Outdoor fan motor fault
F2 2 blinks AD abnormity protection/120N high temperature protection
F3 3 blinks ompressor start failure
F4 4 blinks ompressor exhaust sensor fault
F5 5 blinks ompressor shell temperature protec*on / ompressor shell sensor fault
F6 6 blinks Outdoor environment temprature sensor fault
F7 7 blinks Low/over voltage protection
F8 8 blinks Outdoor module communication fault
F9 9 blinks Outdoor EEPROM fault
FA 10 blinks Return gas sensor fault
F1 Module protection fault/ three-phase fault
L0 Under-voltage protection
L1 / L2 / L3 / L4 ompressor fault
L5 / L6 PF protection
L7 / L AD abnormity protection: PF protection error
L8 Shunt resistance unbalance fault: ompressor drive error
L9 IPM temperature sensor fault
LA ompressor start failure
Ld / LE / LF / LH Direct urrent protection
P2 / PE 5 blinks High-tension switch protection/high-tension switch fault
P3 6 blinks high-tension switch protection/compressor oil lack protection
P4 4 blinks refrigeration anti-overload protection fault locking
P5 5 blinks ompressor exhaust protection fault locking
P6 6 blinks Heating indoor anti-high temprature fault locking
P7 7 blinks Refrigeration anti-freeze protection
P8 / E0 8 blinks Outdoor/Indoor over-current protection
1 blink
10

Troubleshooting Guide
4.2
1. The Foremost Inspecting Items
⑴The input voltage must be within +10% tolerance of the rated Voltage. If it
is not the case, the air-conditioner will probably not work normally.
⑵Check the connecting cord between indoor unit and outdoor unit to see if
it is properly connected. The connecting must be done according to the
wiring diagram, please also notice that even different models may have the
connecting cord of the same specification.
Please check if the marks at the connecting terminal and the marks on the
cord can match, otherwise, the air-conditioner will not work normally.
⑶If the following phenomena are found, the problem is not from the
air-conditioner itself.
11

5
The compressor works
discontinuously at cooling and
dehumidifying mode, and the indoor
fan motor slows down.
The compressor stops internally or the fan
motor slows down to prevent the indoor heat
exchanger from being frozen.
NO. Problems Causes
1The motor is heard operating but the
air-conditioner dose not work when
the indoor unit is powered on
Since the air-conditioner is powered on, it
will come to working condition as long as you
press the ON/OFF button of the remote
control and the Signal is well received.
2
The compressor stops running but
the indoor fan motor keeps working
when it is at cooling mode with the
indoor temperature higher than set
temperature.
If you turn off the air-conditioner and restart it
immediately, it will return to normal in 3
minutes, after that, the air-conditioner will
automatically adjust the indoor fan speed to
what you set.
3The compressor works
discontinuously at dehumidifying
mode.
The air-conditioner will automatically control
the working of the compressor according to
the inside temperature
4The air-conditioner does not work
while the LED display is on.
The TIMER is set with the air-conditioner; it
will be in hold on condition. If the TIMER
setting is cancelled, the air-conditioner will
return to normal working condition
12

2. No Power Display
⑴Items
a) Check if the input voltage is correct?
b) Check if the AC power supply connecting is correct?
c) Check if the output voltage of the manostat L7805 (IC2) is correct?
⑵Trouble shooting procedure
13

connector (CN8)?
⑵Trouble shooting procedure
3. The Indoor Fan Motor Does Not Work
⑴Items
a) Check if the indoor fan motor is connected correctly to the connector (CN8)?
b) Check if the AC input voltage is correct?
c) Check if the IC of indoor fan motor is connected correctly to the connector
(CN2)?
d) Check if the capacity of indoor fan motor is connected correctly to the
14

4. The Outdoor Unit Does Not Work
⑴Items
a) Check if the input voltage is correct?
b) Check if the wire connection of the outdoor connecting terminal is correct?
⑵Trouble shooting procedure
15

5. The Step Motor Does Not Work
⑴Items
a) Check if the input voltage is correct?
b) Check if the step motor controlling the up-down movement firmly
connected to Cn2?
⑵Trouble shooting procedure
16

6. Heating Mode Can Work, But No Hot Air Blow
⑴Check if the set temperature is lower than the indoor temperature?
⑵Check if the indoor PCB is connected to the terminal correctly?
17

7. Remote Control Can Not Work
Trouble shooting rocedure
18