Murdock A151.8FG Series Installation and operating instructions

A151.8FG Series
Barrier Free, 14 Gage Stainless Steel Wall Mounted Electric Drinking Fountain
A151408S-FG / A151408F-FG
TECHNICAL ASSISTANCE TOLL FREE TELEPHONE NUMBER:
1.800.591.9360
Technical Assistance Fax: [phone]
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
CONTEMPORARY WATER COOLERS
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAINS
LIMITED WARRANTY - UNITED STATES & CANADA
This warranty does not cover installation or labor charges and does not apply to materials, which have been
damaged by other causes such as mishandling or improper care or abnormal use. The repair or replacement of the
defective materials shall constitute the sole remedy of the Buyer and the sole remedy of Murdock under this
warranty. Murdock shall not be liable under any circumstances for incidental, consequential or direct charges
caused by defects in the materials, or any delay in the repair or replacement thereof. This warranty is in lieu of all
other warranties expressed or implied. Product maintenance instructions are issued with each unit and disregard
or non-compliance with these instructions will constitute an abnormal use condition and void the warranty.
Stainless steel must be protected on job site during construction and must be properly maintained after the water
has been introduced into the water cooler or drinking fountain, or Murdock’s limited warranty is void.
NOTES TO INSTALLER:
1. Please leave this documentation with the owner of the fixture when finished.
2. Please read this entire booklet before beginning the installation.
3. Check your installation for compliance with plumbing, electrical and other applicable codes.
Murdock warrants that every cooler, bottle filling station, packaged water chiller, fountain and accessory to be free
from defects in material and workmanship under normal use for one (1) year from date of install or eighteen (18)
months after the date of shipment from the factory, whichever comes first.
Murdock warrants the compressor and hermetically sealed refrigeration system, including cooling coil assembly
when part of the hermetically sealed refrigeration system, to be free from defects in material and workmanship
under normal use for an additional four (4) years from the end of the one (1) year period described above.
LIMITED EXPORT WARRANTY - One year on parts only.
COMPLIES WITH
7020-934-001 Date: 07/18/18
Test rating conditions are
compliant with ARI 1010.
Federal
Public Law
111-380
(No Lead) Member of
MURDOCK
15125 Proctor Ave.
City of Industry, CA
91746 U.S.A.
Phone [phone]
626-336-4561
Fax [phone]
www.murdockmfg.com
Murdock assumes no responsibility for use of void or
suspended data. © Copyright Murdock, City of
Industry, CA Member of Morris Group International.
Please visit www.murdockmfg.com for most
current specifications.

IMPORTANT
This fixture is intended to dispense water that has been lowered in temperature, but otherwise remains
unchanged by the materials in the drinking fountain. It is common for electrical equipment to be
grounded to water lines either within a structure or away from it. Every attempt should be made to
prevent this kind of grounding from generating electrical feedback into the drinking fountain creating
electrolysis. Electrolysis will cause a metallic taste or cause water metal content to increase.
NOTICE
A dielectric coupling must be used to connect the drinking fountain to the water supply . A nonmetallic
coupler is furnished with this drinking fountain to meet this requirement.
Prior to roughing consult with local, state, and federal codes for proper mounting height.
ROUGHING-IN AND DIMENSIONAL DRAWING
NOTES: Dimensions shown for Adult ADA compliant installation. For Child ADA compliant parallel
approach installation, decrease height of installation by 3 inches. Provide clear floor space as required.
Adjust vertical dimensions as required to comply with federal, state, and local codes.
A151.8FG
Page 2 of 9
Revised: 07/18/18
7020-934-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
CONTEMPORARY WATER COOLERS
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAINS
FINISHED FLOOR
GENERAL NOTES:
1. ALL DIMENSIONS ARE IN INCHES [MM]
*2. DIMENSIONS SHOWN ARE FOR RECOMMENDED ADULT HEIGHT. ADJUST VERTICAL
DIMENSIONS AS NECESSARY TO COMPLY WITH FEDERAL, STATE, & LOCAL CODES
3. WATER LINE FROM CHILLER TO FOUNTAIN SHOULD BE COVERED WITH SPONGE FOAM
RUBBER OR ICE WATER TYPE INSULATION OF ADEQUATE THICKNESS
13
8"
41
2"
*33"
SUPPLY STOP
VALVE BY
OTHERS
*293
8"
191
4"
20"
19"
WALL
OPENING
3/8" OD SUPPLY
INLET
11"
WALL
OPENING
3/8" OD
COPPER
TUBING
SUPPLIED MTG
FRAME
383
8"
WALL
OPENING
21"
2"
*55
8"
*291
2"
WASTE OUTLET
FOR 1-1/4" P-TRAP

1. Water Supply Service Stop Valve, Water Connections and Electrical Connections to be supplied by
others in accordance with local codes.
IMPORTANT:
6. All burrs must be removed from outside of cut tubes before inserting into strainer or other
components.
4. Completely flush supply lines of all foreign debris before connecting to fixture. Water cooler
designed to not cause problems with taste, odor, color, or sediment. Optional water filter (WF1), is
available should any of these problems arise from the water supply.
3. Waste is 1-1/4” Outer Diameter. Chiller water inlet is 3/8” Outer Diameter copper tube. Chiller water
outlet is 3/8” Outer Diameter copper tube. Drinking Fountain water inlet is 3/8” Outer Diameter
copper tube. Water line by others from in-wall chiller to drinking fountain must have adequate
insulation.
2. Provide 4” minimum clear space in front of bottom trim panel and above in-wall chiller to allow for
proper ventilation.
10. Fixture operates within water pressure range of 20 to 105 psig. Acorn Engineering will not warranty
chiller damaged when connected to supply lines with flow pressure lower that 20 psig or higher
than 105 psig. A pressure regulator must be furnished by others on supply line if inlet pressure is
greater than 105 psig.
12. Per UPC 609.10-All building water supply systems in which quick acting valves are installed shall
be provided with devices to absorb the hammer caused by high pressure resulting from the quick
closing of the valve. These pressure-absorbing devices shall be approved mechanical devices.
Water pressure-absorbing devices shall be installed as close as possible to the quick closing valve.
11. Due to cold waste water, Acorn Engineering recommends that waste piping supplied by installer be
insulated appropriately to prevent excessive condensation.
5. Do NOT solder tubes inserted into the chiller or the fountain strainer as damage to the o-rings on
the push-in fittings may result.
8. This unit must be grounded per the requirements of applicable electrical codes.
9. WARNING: Warranty is voided if installation is not made following current Acorn Engineering
installation instructions and if components are assembled to the fixture that are not approved by
Acorn Engineering.
7. Power supply must be identical in voltage, cycle and phase to that specified on the chiller data
plate.
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
CONTEMPORARY WATER COOLERS
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAINS
A151.8FG
Page 3 of 9
Revised: 07/18/18
7020-934-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of

2. Verify frame chiller shelf is secure and install
the chiller following the instructions included
with the chiller
3. Hang upper trim panel on mounting frame.
Note: The included 1” brackets do not get used
with this installation and the plastic spacers are
typically not required and can be discarded.
INSTALLATION:
1. Install –MF3 Chiller and Drinking Fountain Wall
Mounting Frame following the instructions
included with the frame.
4. Install the four threaded studs into the Wall
Mounting Frame.
6. Slide fixture over studs and secure with nuts and washers 2 .
5. Remove the drinking fountain bottom access panel 1 . Set the access panel aside in a safe place
where it will not be damaged and place the screws in a secure location where they will not be lost.
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
CONTEMPORARY WATER COOLERS
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAINS
A151.8FG
Page 4 of 9
Revised: 07/18/18
7020-934-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of

7. Remove the drinking fountain bottom access panel 1 . Set the access panel aside in a safe place
where it will not be damaged and place the screws in a secure location where they will not be lost.
8. Slide fixture over studs and secure with nuts and washers 2 .
9. After thoroughly flushing the 3/8” outer diameter supply line, connect water supply to in-wall chiller
and provide connection from chiller to drinking fountain in-line strainer 5 .
10. Reassemble access panel 1 to unit with screws previously removed.
2. Air within the drinking fountain system or the structure supply piping will cause an irregular bubbler
outlet stream until purged out by incoming water. Covering the bubbler with a clean cup (or similar
object) is recommended when first activating drinking fountain to prevent excessive splashing.
Depress front push pad until steady water stream is achieved.
3. If water flow requires adjustment, insert a slotted narrow blade screwdriver in the hole centered on
the underside of the fixture in the knee clearance area up to the flow regulator. Turning clockwise
will increase flow and turning counterclockwise will decrease flow.
4. Recheck all water connections with water flowing through system.
5. Provide power to water chiller and make sure unit begins to function.
TROUBLE SHOOTING:
IMPORTANT: BEFORE MAKING ANY OF THE REPAIRS LISTED, MAKE SURE THE
WATER CHILLER IS DISCONNECTED FROM THE ELECTRICAL SUPPLY AND THE
WATER SUPPLY VALVE IS SHUT OFF.
a. Cartridge – The water flow can be adjusted using a slotted narrow blade screwdriver and turning
clockwise to increase flow and counterclockwise to decrease flow.
6. Assemble louvered bottom trim panel with screws provided to brackets on either side of wall
mounting frame.
b. Cold Water Thermostat – The water temperature can be adjusted using a slotted screwdriver
and turning clockwise to make colder and counterclockwise to make warmer.
1. Before connecting power supply, but after thoroughly flushing the supply line and connecting it to
the cooler, turn on building water supply and check all connections for leaks.
1. Adjustments
START UP:
2. Compressor Does Not Run
c. Check for loose wires within the compressor box. The incoming power leads must be connected
to the overload and relay.
d. If all components check positive for continuity then test the wiring harness plug for continuity to
see if there is a broken wire within the wiring harness insulation.
a. Check the electrical supply for power and correct voltage. The incoming voltage must be within
10% of the rated voltage on the serial nameplate.
b. If the cold thermostat capillary bulb loses its charge or becomes kinked it will fail in the open
position causing a disruption of power to the compressor. Disconnect electrical supply to the
water chiller and using an ohm meter check for continuity across the two electrical terminals on
the thermostat. Install a new thermostat if there is no continuity.
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
CONTEMPORARY WATER COOLERS
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAINS
A151.8FG
Page 5 of 9
Revised: 07/18/18
7020-934-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of

WATER CHILLER IS DISCONNECTED FROM THE ELECTRICAL SUPPLY AND THE
b. If the cold thermostat capillary bulb loses its charge or becomes kinked it will fail in the open
position causing a disruption of power to the compressor. Disconnect electrical supply to the
water chiller and using an ohm meter check for continuity across the two electrical terminals on
the thermostat. Install a new thermostat if there is no continuity.
4. Recheck all water connections with water flowing through system.
TROUBLE SHOOTING:
8. Slide fixture over studs and secure with nuts and washers 2 .
2. Air within the drinking fountain system or the structure supply piping will cause an irregular bubbler
outlet stream until purged out by incoming water. Covering the bubbler with a clean cup (or similar
object) is recommended when first activating drinking fountain to prevent excessive splashing.
Depress front push pad until steady water stream is achieved.
c. Check for loose wires within the compressor box. The incoming power leads must be connected
to the overload and relay.
9. After thoroughly flushing the 3/8” outer diameter supply line, connect water supply to in-wall chiller
and provide connection from chiller to drinking fountain in-line strainer 5 .
a. Cartridge – The water flow can be adjusted using a slotted narrow blade screwdriver and turning
clockwise to increase flow and counterclockwise to decrease flow.
10. Reassemble access panel 1 to unit with screws previously removed.
1. Before connecting power supply, but after thoroughly flushing the supply line and connecting it to
the cooler, turn on building water supply and check all connections for leaks.
a. Check the electrical supply for power and correct voltage. The incoming voltage must be within
10% of the rated voltage on the serial nameplate.
1. Adjustments
IMPORTANT: BEFORE MAKING ANY OF THE REPAIRS LISTED, MAKE SURE THE
d. If all components check positive for continuity then test the wiring harness plug for continuity to
see if there is a broken wire within the wiring harness insulation.
START UP:
b. Cold Water Thermostat – The water temperature can be adjusted using a slotted screwdriver
and turning clockwise to make colder and counterclockwise to make warmer.
WATER SUPPLY VALVE IS SHUT OFF.
7. Remove the drinking fountain bottom access panel 1 . Set the access panel aside in a safe place
where it will not be damaged and place the screws in a secure location where they will not be lost.
5. Provide power to water chiller and make sure unit begins to function.
3. If water flow requires adjustment, insert a slotted narrow blade screwdriver in the hole centered on
the underside of the fixture in the knee clearance area up to the flow regulator. Turning clockwise
will increase flow and turning counterclockwise will decrease flow.
6. Assemble louvered bottom trim panel with screws provided to brackets on either side of wall
mounting frame.
2. Compressor Does Not Run
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
CONTEMPORARY WATER COOLERS
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAINS
A151.8FG
Page 6 of 9
Revised: 07/18/18
7020-934-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of

c. A restriction or moisture in the system will also cause intermittent cycling. A certified refrigeration
mechanic should be contacted in this situation.
a. The most common cause for a water chiller to run without producing cold water is a loss of
refrigerant. The water chiller must be taken to a certified refrigerant technician for repairs.
c. An incorrect refrigerant charge, restriction or defective compressor (not pumping) will also cause
the compressor to run without producing cold water. All these signs indicate a problem within
the refrigeration system and the water chiller must be checked by an authorized service
company.
6. Restricted Or No Water Flow
1. Motors have lifetime lubrication and do not require scheduled maintenance.
a. A dirty condenser or a blocked fan will cause a high head pressure and frequent cycling of the
overload protector.
d. Change the overload or relay if defective.
4. Compressor Cycling On Overload Protector
b. Check the incoming voltage to make sure it is within 10% of the serial nameplate rating.
b. Make sure the condenser fan motor is operative. The fan blade must turn freely to help remove
the heat of compression.
3. Compressor Runs – Water Is Warm
5. Noisy Operation
b. Check the compressor mounting to make sure the pins and clips are not rattling. If the
compressor appears to be noisy internally, it must be replaced.
a. Check to make sure the fan blade is rotating freely.
b. Verify minimum 20 psig supply line flow pressure.
d. Check the water inlet strainer. Sediment from the main supply can get trapped in the screen
along with installation materials such as pipe dope and flux. The screen should be cleaned and
checked on a regular basis and replace if needed.
e. The cartridge valve located in the water control assembly or bubbler can also become clogged
with foreign material. The cartridge valve can only be replaced and not repaired.
c. Check for twists or kinks in outlet tubing.
a. Ensure water supply service stop valve is fully open.
f. The water chiller may also develop a freezing condition in which the water will become frozen
inside the evaporator coil. This indicates a refrigeration problem or thermostat failure in which
case the water chiller needs to be checked by a qualified technician.
7. Water Drips Or Will Not Shut Off
a. Open fixture. Loosen nuts holding valve bracket assembly to bottom of fixture but do not
remove. Move complete valve bracket assembly further back from the front push pad and
tighten to lock in place.
b. Replace valve cartridge.
CLEANING & MAINTENANCE GUIDE:
2. Excess dirt or poor ventilation will cause the compressor overload protector to turn the compressor
off and it will cycle on and off with no cold water coming out of bubbler. Periodically clean with
vacuum cleaner, air hose or brush the condenser fins and cabinet ventilation louvers. In
environments where dirt and dust is more prevalent, clean more frequently.
3. Periodically remove fountain top and clean out in-line strainer.
4. Do NOT use harsh chemicals, abrasive or petroleum based cleaners. Use of these will void the
Acorn Engineering warranty.
5. Exterior panels can be cleaned using mild household detergents or warm, soapy water. Extra care
must be used cleaning chrome plated items and mirror finished stainless steel. They can scratch
easily and should only be cleaned using a clean, soft cloth and mild soap with water or a mild glass
cleaner.
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
CONTEMPORARY WATER COOLERS
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAINS
A151.8FG
Page 7 of 9
Revised: 07/18/18
7020-934-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
CONTEMPORARY WATER COOLERS
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAINS
A151.8FG
Page 8 of 9
Revised: 07/18/18
7020-934-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of
PUSH-IN FITTING INSTALLATION
NOTE: FITTINGS AND TUBE SHOULD BE KEPT
CLEAN, BAGGED AND UNDAMAGED PRIOR TO
INSTALLATION.
2. Pull on the fitted tubing to ensure it is secure. Tube
should not come free from the fitting. Water test the
connection assembly prior to leaving the site to ensure
there are no leaks.
DISCONNECTING THE TUBE:
To disconnect the tube from the fitting ensure that the
water line is depressurized. Push collet square towards
the push-in fitting body and hold. While holding the collet
in, pull on the PE tubing to remove from the push-in fitting.
TO CUT TUBE:
Cut to fit length of 1/4” PE tubing and remove any burrs
or sharp edges. Ensure that the outside diameter is free
from score marks. Tube ends should be square.
1. Firmly and fully insert the tubing end into the push-in
fitting up to the tube stop located approximately ½”
deep.
INSERTING THE TUBE:
COLLET
COLLET
O-RING
O-RING
TUBE STOP
COLLET
COLLET
COLLET

Repairs must be made with Murdock Manufacturing parts only. Please order through your local
representative or distributor. The phone number to locate your local representative is 1.800.591.9360.
FOUNTAIN PARTS BREAKDOWN
CHILLER PARTS BREAKDOWN
Reference installation manual included with in-wall chiller for appropriate Chiller Parts Breakdown.
ITEM # PART NUMBER DE SCRIPTION ITEM # PART NUMBER DESCRIPTION
1 0296-025-199 Center Reject Hex Driver Bit 8A 7000-012-001 Stainless Steel Bubbler Assembly
2 0112-002-000 Center Reject Allen Button Hd Screw 8B 7000-099-002 Flexible Gray Bubbler Assembly
3 7000-015-000 1-1/4” Out er Diameter P-Trap 9 7000-068-001 Retaining Ring & But ton Assembly
4 7000-021-000 “Y” Strainer 10 7000-069-001 Valve Cart ridge With Foam Washer
5 7000-005-199 Drain Adapter 11 7000-065-001 Recessed Pushbutton Valve Assembly
6 7000-006-000 Flat Drain Adapter Gasket 12 7003-093-001 Flow Restrictor - Low-Flow Bubbler Only
7 0152-010-000 Center Reject Allen Flat Head Screw
6
5
4
3
2
1
6
9
10
11
8B
8A
** 12
NOTE:
** Flow Restrictor Only Available
With Low Flow Bubbler.
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
CONTEMPORARY WATER COOLERS
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAINS
A151.8FG
Page 9 of 9
Revised: 07/18/18
7020-934-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of