Murdock A172-UG-D1-BFS Series Installation and operating instructions

COMPLIES WITH
7020-988-001 Revised: 06/01/2023 A
Murdock assumes no responsibility for use of void or
suspended data. © Copyright Murdock, City of
Industry, CA Member of Morris Group International.
Please visit www.murdockmfg.com for most
current specifications.
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAIN
A172-UG-D1-BFS Series & A172-UG-VR-D1-BFS Series
Universal Bi-Level, Barrier Free, Wall Mounted Drinking Fountain
A172100F-UG-D1-BFS / A178400F-UG-D1-BFS / A172100S-UG-D1-BFS / A172400S-UG-D1-BFS
A172100F-UG-VR-D1-BFS / A172400F-UG-VR-D1-BFS / A172100S-UG-VR-D1-BFS / A172400S-UG-VR-D1-BFS
TECHNICAL ASSISTANCE TOLL FREE TELEPHONE NUMBER:
1.800.591.9360
Technical Assistance E-Mail: [email protected]
A172400F-UG-D1-BF2S-BCD
A172400S-UG-VR-D1-BF1S
NOTES TO INSTALLER:
1. Please leave this documentation with the owner of the fixture when finished.
2. Please read this entire booklet before beginning the installation.
3. Check your installation for compliance with plumbing, electrical and other applicable codes.
4. IMPORTANT: Water supply to unit from RO Reverse Osmosis filtration systems will damage
fixture components and void product Warranty.
Federal
Public Law
111-380
(No Lead)
NSF/ANSI/CAN 61 Member of 15125 Proctor Ave, City of Industry,
CA, 91746 U.S.A.
Phone [phone]
www.murdockmfg.com

A172-UG-VR-D1-BFS
Page 2 of 14
Revised: 06/01/2023 A
7020-988-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAIN
IMPORTANT
This Fixture is intended for indoor use only** and is not suitable for installation in an area where a water jet could be used as
well as in environments where freezing may occur. A dielectric coupling must be used to connect the drinking fountain to the
water supply. NOTE: A nonmetallic coupler is furnished with this drinking fountain to meet this requirement.
**NOTE: -VR Series units are rated for outdoors. Refer to page 5 for complete details and requirements.
ROUGHING-IN AND DIMENSIONAL DRAWING
Prior to roughing consult with local, state, and federal codes for proper mounting height. All installation and service may only
be performed by authorized personnel. No unauthorized persons shall have access to the service area.
Mounting Carrier: Refer to Installation details provided by Carrier manufacturer when unit is to be installed with In-W all
®
Mounting Carrier (provided by others). Compatible J.R. Smith brand Carrier model is Figure # 0834-4P.
A172-UG-D1-BFS Series Universal Bi-Level Wall Mounted Drinking Fountain
(Standard Configuration Left Unit High with Right Unit Low. Rough-ins are the same for -VR models.)
NOTES: Dimensions indicated * are for ADA frontal approach installation. Adjust vertical dimension * as required to
comply with federal, state, and local codes. For Child ADA compliant parallel approach, decrease spout height to 30”
maximum above finished floor. Provide Clear Floor Space as required. Compliance is subject to the interpretation and
requirements of the local Code Authority.
Electrical Requirements (Non Chilled):
For -BF2S -SO Sensor Bottle Filler
- Provide Duplex Receptacle on GFCI Protected Circuit
- 115VAC, 60Hz, 1A
GENERAL NOTES:
1. ALL DIMENSIONS ARE IN INCHES [MM]
2. DIMENSIONS SHOWN ARE FOR ADA ADULT HEIGHT. ADJUST
VERTICAL DIMENSIONS AS NECESSARY TO COMPLY WITH
FEDERAL, STATE & LOCAL CODES
3. STOP VALVE, P-TRAP & ELECTRICAL OUTLET NOT SUPPLIED
*
A. 3/8" O.D. SUPPLY INLET
B. WASTE OUTLET FOR P-TRAP BY OTHERS FOR
PROVIDED 1-1/4" O.D. TAILPIECE
C. ELECTRICAL SERVICE ROUGH. SEE NOTE.
D. Ø3/8" HANGER BRACKET PUNCHING, 6 PLACES
FOR ANCHORING HARDWARE BY OTHERS
E. Ø1/4" PUNCHING, 3 PLACES FOR ANCHORING
HARDWARE BY OTHERS
F. 1-1/4" [32] O.D. TAILPIECE FOR P-TRAP BY OTHERS
*27"
[687]
F
43
4"
[119]
*33"
[838]
21"
[533]
*313
4"
[806]
A
B
CE
D
193
8"
[492]
7" [178] TYP
2813
16"
[732]
2" [51]
4 1
4" [108]
1315
16"
[354]
177
8"
[454]
221
4"
[565]
2"
[51]
63
8"
[162]
TYP
5 3
4" [146]
1915
16"
[506]
3413
16"
[884]
2"
[51]
6"
[152]
371
8"
[943]
REF

A172-UG-D1-BFS SERIES UNIVERSAL BI-LEVEL DRINKING FOUNTAIN
(NOTE! Alternate Configuration Left Unit Low with Right Unit High)
IMPORTANT:
1. Water supply is 3/8” Outside Diameter copper tube. Waste is 1-1/4” Outside Diameter.
2. Completely flush supply lines of all foreign debris before connecting to fixture. Water cooler designed
to not affect taste, odor, color, or sediment. Optional water filter (WF1) is available should any of these
problems arise from the water supply.
3. Do NOT solder copper tube when inserted into the coupler as damage to the o-ring will result.
4. All burrs must be removed from outside of cut tubes before inserting into coupler or other components.
5. WARNING: Warranty is voided if installation is not made following current Murdock Manufacturing
installation instructions and if components are assembled to the fixture that is not approved by
Murdock Manufacturing.
6. Fixture operates within water pressure range of 20 to 105 psig. Murdock Manufacturing will not
warranty fixtures damaged when connected to supply lines with flow pressure lower than 20 psig or
higher than 105 psig. A pressure regulator must be furnished by others on supply line if inlet pressure
is greater than 105 psig. Consult with UPC and local codes for maximum allowable water
pressures.
7. Per UPC 609.10- All building water supply systems in which quick acting valves are installed shall be
provided with devices to absorb the hammer caused by high pressure resulting from the quick closing
of the valve. These pressure-absorbing devices shall be approved mechanical devices. Water
pressure-absorbing devices will be installed as close as possible to the quick closing valve.
A172-UG-VR-D1-BFS
Page 3 of 14
Revised: 06/01/2023 A
7020-988-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAIN
NOTE: REFER TO NOTES ON PREVIOUS PAGE FOR ADDITIONAL DETAILS ON ELECTRICAL ROUGH-IN AND ADA.
A. 3/8" O.D. SUPPLY INLET
B. WASTE OUTLET FOR P-TRAP BY OTHERS FOR
PROVIDED 1-1/4" O.D. TAILPIECE
C. ELECTRICAL SERVICE ROUGH. SEE NOTE.
D. Ø3/8" HANGER BRACKET PUNCHING, 6 PLACES (TYP)
FOR ANCHORING HARDWARE BY OTHERS
E. Ø1/4" PUNCHING, 3 PLACES FOR ANCHORING
HARDWARE BY OTHERS
F. 1-1/4" [32] O.D. TAILPIECE FOR P-TRAP BY OTHERS
GENERAL NOTES:
1. ALL DIMENSIONS ARE IN INCHES [MM]
2. DIMENSIONS SHOWN ARE FOR ADA ADULT HEIGHT. ADJUST
VERTICAL DIMENSIONS AS NECESSARY TO COMPLY WITH
FEDERAL, STATE & LOCAL CODES
3. STOP VALVE, P-TRAP & ELECTRICAL OUTLET NOT SUPPLIED
*27"
[687]
F
43
4"
[119]
*33"
[838]
21"
[533]
*313
4"
[806]
A
B
C
E
D
253
8"
[645]
7" [178] TYP
2813
16"
[732] 2"
[51]
4 1
4" [108]
1315
16"
[354]
237
8"
[606]
221
4"
[565]
2"
[51]
63
8"
[162]
TYP
5 3
4"
[146]
1915
16"
[506]
3413
16"
[884]
2"
[51]
6"
[152]
371
8"
[943]
REF

PRIOR TO INSTALLATION:
Important: Some options may slightly alter installation. To ensure proper installation, review the Manual thoroughly
and verify rough-ins before beginning work. Leave this Manual with the owner or maintenance personnel upon
completion of installation.
— Fixture mounting requirements: Industry standard wall construction, adequate to support the fixture
and installer-provided Wall Anchors sufficient to secure the fixture.
— Receptacle(s) must be wired to a GFCI protected circuit. Fixture must be earth grounded per NEC
(National Electric Code).
— Inspect fixture and all parts for damage.
—To avoid a hazard due to instability, fixture must be installed in accordance with the instructions.
INSTALLATION:
Choose configuration; Remove and reinstall filler plate, item [31] and reverse drain assembly if
required for alternate mounting configuration.
1. Mount hanger bracket to wall horizontally level as shown in Roughing-In and Dimensional Drawing. Note:
Adjust height of bracket if bubbler outlet height is required to vary from that shown.
WARNING: Hanger Bracket MUST be securely anchored to wall with fasteners sufficient to support 3 times
the weight of drinking fountain. If wall can not provide adequate support, order and install optional fixture
support carrier.
NOTE: If wall cannot provide adequate support, order and install fixture support carrier (by others).
NOTE: If replacing a competitors Water Cooler you may be able to use existing mounting bracket
2. Remove the bottom cover from the drinking fountain and set aside in a safe place. Save the screws in a
secure location for re-use in later stages of installation.
3. Hang the drinking fountain on the hanger brackets ensuring the bracket tabs engage AND seat in the slots in
the back of the drinking fountain. Verify drinking fountain are level, left to right AND front to back from bottom
of unit. NOTE: The bubbler stream may be adversely affected if units are not square and level. Bottom of units
and louvers should be used as reference to verify unit is square and plumb.
4. Anchor the drinking fountain to the wall at the lower mounting points in each back panel. Shim lower mounting
points to level unit if necessary.
5. Thoroughly flush the 3/8” O.D. supply line and then connect drinking fountain to water supply angle stop valve
(by others) with supplied 3/8” O.D. copper tube.
6. Use supplied flexible hose and clamps to connect waste tailpiece from the upper unit to the waste tailpiece of
lower unit and then make up 1-1/4” O.D. P-Trap waste connection. Waste P-Trap by others.
STANDARD WASTE CONFIGURATION ALTERNATE WASTE CONFIGURATION
ITEM 31
FILLER PLATE
ITEM 31
FILLER PLATE
A172-UG-VR-D1-BFS
Page 4 of 14
Revised: 06/01/2023 A
7020-988-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAIN

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAIN
A172-UG-VR-D1-BFS
Page 5 of 14
Revised: 06/01/2023 A
7020-988-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of
STANDARD CONFIGURATION
WEATHER STRIP
WEATHER STRIP
(BETWEEN UPPER
AND LOWER UNITS)
CAULKING
CAULKING
OUTDOOR INSTALLATION INSTRUCTIONS - A172-UG-VR-D1-BFS ONLY:
IMPORTANT: Only A172-UG-VR-D1-BFS Series units are rated for outdoor use.
Ÿ Units installed outdoors presume average conditions and require adequate protection to prevent
exposure to extreme hot or cold temperatures which will affect Warranty.
Ÿ Best practices include installation beneath an overhang and avoiding direct sunlight.
Ÿ Continual ambient temperatures exceeding 80°F (26.67°C) may cause compressor to wear prematurely.
Ÿ Units are not freeze resistant.
Ÿ Caulk all around the basin where it contacts the wall and where apron contacts the wall as shown, to
reduce the possibility of rain water from leaking into the cabinet. DO NOT CAULK THE REMOVABLE
LOWER ACCESS COVER.
START UP:
1. Before connecting water supply and assembling bottom cover to drinking fountain, but after thoroughly
flushing the supply line and connecting it to the fixture, turn on building water supply and check all
connections for leaks.
2. Air within the drinking fountain system or the structure supply piping will cause an irregular bubbler outlet
stream until purged out by incoming water. Covering the bubbler with a clean cup (or similar object) is
recommended when first activating drinking fountain to prevent excessive splashing. Depress the pushbutton
until steady water stream is achieved.
3. If water flow requires adjustment, insert a slotted narrow blade screwdriver in the hole centered on the
underside of the fixture in the knee clearance area up to the flow regulator. Turning clockwise will increase
flow and turning counterclockwise will decrease flow.
4. Recheck all water and drain connections with water flowing through system.
5. IMPORTANT! Thoroughly, inspect all unit connections for water leaks.
6. Assemble bottom cover to drinking fountain with screws furnished.

A172-UG-VR-D1-BFS
Page 6 of 14
Revised: 06/01/2023 A
7020-988-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAIN
Cartridge Valve
Assembly
To Bottle Filler
Water Supply
Tubing
Remove For Bottle
Filler Use
Water Supply
Tubing
A172-UG-D1-BFS & A172-UG-VR-D1-BFS BI-LEVEL UNIT PIPING INSTALLATION (WITH -BF OPTIONS)
CLEANING & MAINTENANCE GUIDE:
1. Periodically remove access panels and clean out in-line strainer.
2. Do NOT use harsh chemicals, abrasive or petroleum based cleaners. Use of these will void the
Acorn warranty.
3. Exterior panels can be cleaned using mild household detergents or warm, soapy water. Extra care
must be used cleaning chrome plated items and mirror finished stainless steel.
They can scratch easily and should only be cleaned using a clean,
soft cloth and mild soap with water or a mild glass cleaner.

PUSH-IN FITTING INSTALLATION
NOTE: FITTINGS AND TUBE SHOULD BE KEPT
CLEAN, BAGGED AND UNDAMAGED PRIOR TO
INSTALLATION.
2. Pull on the fitted tubing to ensure it is secure. Tube
should not come free from the fitting. Water test the
connection assembly prior to leaving the site to ensure
there are no leaks.
DISCONNECTING THE TUBE:
To disconnect the tube from the fitting ensure that the
water line is depressurized. Push collet square towards
the push-in fitting body and hold. While holding the collet
in, pull on the PE tubing to remove from the push-in fitting.
TO CUT TUBE:
Cut to fit length of 1/4” PE tubing and remove any burrs
or sharp edges. Ensure that the outside diameter is free
from score marks. Tube ends should be square.
INSERTING THE TUBE:
1. Firmly and fully insert the tubing end into the push-in
fitting up to the tube stop located approximately ½”
deep.
COLLET
COLLET
O-RING
O-RING
TUBE STOP
COLLET
COLLET
COLLET
A172-UG-VR-D1-BFS
Page 7 of 14
Revised: 06/01/2023 A
7020-988-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAIN

CONTEMPORARY WATER COOLERS
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
WATER COOLERS
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of
Page 8 of 14 A172-UG-VR-D1-BFS Revised: 06/01/2023 A
7020-988-001
THE HOLES OF THE UNIT FRAME.
DISCONNECT FROM THE POWER SUPPLY.
PLACE FILTER/BRACKET ASSEMBLY 1 ON INSIDE OF
WATER SUPPLY. IF UNIT IS A REFRIGERATED MODEL,
UNIT FRAME AND ALIGN HOLES IN THE BRACKET WITH
REMOVE THE BOTTOM HOUSING AND TURN OFF UNIT
B-
A-
USE THE SCREWS 2 PROVIDED TO PASS THRU THE
FRAME CLEARANCE HOLES AND SCREW INTO THE
C-
CONNECT NEW PE TUBE PROVIDED WITH FILTER TO
EVAPORATOR PUSH-IN INLET, WHERE TUBE WAS
UNION 4 TO WHERE IT CONNECTS TO THE EVAPORATOR.
E-
F-
D- FOLLOW PE TUBE FROM "Y" STRAINER 3 OR PUSH-IN
IMPORTANT: FLUSH 5 GALLONS OF WATER THRU THE G-
TURN ON WATER. CHECK FOR LEAKS.
FILTER BEFORE ALLOWING FIXTURE USE.
CHECK UNIT FOR PROPER OPERATION.
RE-INSTALL BOTTOM HOUSING.I-
IF REFRIGERATED UNIT, TURN ON POWER SUPPLY AND H-
DISCONNECT TUBE FROM EVAPORATOR, CONNECT TO
REPLACEMENT.
TO DISCONNECT THE TUBE FROM THE PUSH-IN FITTING
TUBE HOLD DOWN GRIPPER AND PULL TUBE OUT
SLOWLY.
WAY TO MAKE A GOOD CONNECTION. CARTRIDGE
TO CONNECT PUSH-IN FITTINGS, PUSH TUBE IN ALL THE
1-
2-
BRACKET HOLES.
REMOVED.
FILTER INLET PUSH-IN CONNECTION.
-WF1, -WF3 INSTALLATION INSTRUCTIONS:
NOTES:
2
4
3
1
1/4" PUSH-IN OUTLET
REPLACEMENT CARTRIDGE
-RWF3 PART # 7012-318-000
-RWF1 PART # 7012-313-000
WF1 / WF3 Filter Assembly Shown
OPTIONAL WATER FILTER INSTALLATION:
REFER TO INSTALLATION DETAILS PROVIDED WITH -WF1EZ
(REFERENCE INSTALLATION DRAWING 7020-009-001)
-WF1EZ FILTER (Detail A):
-WF3 FILTER CARTRIDGE INSTALLATION:
WATER FILTER HAS 3000 GALLON CAPACITY, CARTRIDGE
WILL REQUIRE REPLACEMENT AFTER 100 HOURS OF ACTUAL
OPERATIONAL USAGE. FREQUENCY OF FIXTURE OPERATION
REPLACEMENT.
WILL DETERMINE TIME FRAME FOR CARTRIDGE
-WF1 FILTER CARTRIDGE INSTALLATION:
WATER FILTER HAS 1500 GALLON CAPACITY, CARTRIDGE
WILL REQUIRE REPLACEMENT AFTER 50 HOURS OF ACTUAL
OPERATIONAL USAGE. FREQUENCY OF FIXTURE OPERATION
REPLACEMENT. (-SO, -SOC, -FG MODELS)
WILL DETERMINE TIME FRAME FOR CARTRIDGE
IMPORTANT:
FLUSH 3-5 GALLONS OF WATER THROUGH THE
FILTER BEFORE INITIAL USE!
(Bubbler run time for approximately 10-15 minutes,
Bottle Filler run time for approximately 3-5 minutes.)
Detail A

A172-UG-VR-D1-BFS
Page 9 of 14
Revised: 06/01/2023 A
7020-988-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAIN
STANDARD CARTRIDGE REPLACEMENT/ STRAINER MAINTENANCE
Note: Use the universal maintenance tool to perform the following:
1. Strainer plug must be removed before cartridge replacement and strainer
maintenance (no need to turn the water off at the angle stop). Some residual water will drain
during plug removal.
2. Clean strainer as needed using clean water.
3. Cartridge replacement - insert diamond end of the universal tool into push button, rotate 90 degrees
and pull firmly to remove the button. Remove cartridge retaining nut . Remove and replace cartridge.
When replacing cartridge be sure to align the inlet and outlet ports on the cartridge with the ports in
the valve body.
— NOTE: STRAINER SCREEN MUST BE IN PLACE FOR WATER TO FLOW.
2
4
3
1
5
ITEM PART NUMBER DESCRIPTION
5 7003-830-000 UNIVERSAL MAINTANANCE TOOL
4 7003-864-000 STRAINER FILTER SCREEN
3 7003-097-001 O-RING &STRAINER PLUG
2 7000-060-000 FLOW REGULATOR CARTRIDGE(05 GPMG)
1 7003-095-001 VALVE ASSEMBLY

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAIN
A172-UG-VR-D1-BFS
Page 10 of 14
Revised: 06/01/2023 A
7020-988-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of
-VR SERIES VANDAL RESISTANT CARTRIDGE REPLACEMENT/ STRAINER MAINTENANCE
Note: Use the -VR maintenance tool to perform the following:
1. Strainer plug 4 must be removed before cartridge replacement and strainer
maintenance (no need to turn the water off at the angle stop). Some residual water will drain
during plug removal.
2. Clean strainer 4 as needed using clean water.
3. Cartridge replacement - Rotate and remove -VR pushbutton escutcheon 6 to release pushbutton 7 and springs 8 9 to
access cartridge.
4. Remove cartridge retaining nut 10 . Remove and replace cartridge 2 . When replacing cartridge be sure to align the inlet
and outlet ports on the cartridge with the ports in the valve body.
5. Install item 10 using maintenance tool 5 (Be careful not to over tighten)
6. Install button assembly items 6 7 8 9 using maintenance tool 5 . Insure springs are installed in button correctly.
7. Reinstall strainer 4 and plug 3 using maintenance tool 5 .
NOTE: STRAINER FILTER SCREEN
MUST BE IN PLACE FOR
WATER TO FLOW.
2
4
3
1
5
5
6
7
8
9
10
11
ITEM PART NUMBER DESCRIPTION
1 7003-095-001 VALVE ASSEMBLY
2 7000-060-000 FLOW REGULATOR CARTRIDGE(0.5 GPM)
3 7003-097-001 O-RING &STRAINER PLUG
4 7003-864-000 STRAINER FILTER SCREEN
5 7003-194-199 (-VR) MAINTENANCE TOOL
6 7003-197-199 (-VR) PUSHBUTTON ESCUTCHEON, CHROME
7 7003-196-199 (-VR) PUSHBUTTON, CHROME
8 7003-195-000 (-VR) PUSHBUTTON OVERTRAVEL SPRING
9 7003-193-000 (-VR) PUSHBUTTON RETURN SPRING
10 7000-052-000 RETAINING NUT
11 7003-099-001 (-VR) PUSHBUTTON ASSY - ITEMS #5 THRU #9

A172-UG-VR-D1-BFS
Page 11 of 14
Revised: 06/01/2023 A
7020-988-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAIN
Universal Maintenance Tool
-Button Removal
-Cartridge Retaining Nut
-Strainer Plug
-Removal of P.E. Tubing from
Push-in Fittings
25
NOTE:
** Flow Restrictor Only Available
With Low Flow Bubbler.
A172-UG-D1-BFS DRINKING FOUNTAIN PARTS BREAKDOWN
NOTE: See following page for fixture drawing corresponding to table of parts below.
5
4
2
3
1
13
15
9
17 15"
20
18
22
21
17 24"
23
25
24
22
21
17 24"
23
17 15"
7
7
6
4
3
2
1
8
9
10
14
13
19
11
12
20
11
12
16
17 2"
24
17 15"

Repairs must be made with Murdock Manufacturing parts only. Please order through your local
representative or distributor.
A172-UG-D1-BFS DRINKING FOUNTAIN PARTS BREAKDOWN TABLE
NOTE: See previous page for fixture drawing corresponding to table of parts below.
A172-UG-VR-D1-BFS
Page 12 of 14
Revised: 06/01/2023 A
7020-988-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of
I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAIN
ITEM # PART NUMBER DESCRIPTION
7003-001-199 BASIN TOP
7003-871-199 BASIN TOP w/ Ø1/2" HOLE
7000-099-002 STANDARD FLEXIBLE BUBBLER ASSEMBLY
7000-012-001 LEAD -FREE STAINLESS STEEL BUBBLER ASSEMBLY
3 0124-008-000 #8 x 3/4" LG FLAT HD SELF TAPPING TORX C/R SCREW
4 7000-006-000 FLAT DRAIN GASKET
5 7003-181-000 DRAIN TAILPIECE (LONG)
6 7003-180-000 DRAIN ADAPTER
7 7003-184-000 7/8" SPRING CLAMP
8 7003-183-199 DRAIN HOSE
9 7003-950-199 HANGER BRACKET
7003-956-020 FILLER PLATE - GRAY
7003-825-199 FILLER PLATE - STAINLESS STEEL
11 7003-900-199 BACK PANEL
12 7003-007-199 SUPPORT STRUT
13 0124-036-000 #8 x 1/2" LONG TORX ROUND HEAD C/R SCREW
14 0124-050-000 #8 x 3/8" LONG PHILLIPS PAN HEAD SCREW
15 1895-123-000 1/4" x 3/8" O.D. PUSH-IN SUPPLY INLET CONNECTION
16 1895-710-000 1/4" O.D. TUBE UNION TEE (PUSH-IN)
17 2169-000-000 1/*4" O.D. PE TUBING (BLUE)
7003-955-020 RIGHT CABINET - GRAY
7003-824-199 RIGHT CABINET - STAINLESS STEEL
7003-954-020 LEFT CABINET - GRAY
7003-823-199 LEFT CABINET - STAINLESS STEEL
20 0124-031-000 #8x3/8" LONG SLOTTED HEX WASHER HEAD SCREW
21 7003-095-001 VALVE ASSEMBLY
7003-953-002 APRON ASSEMBLY - GRAY
7003-826-002 APRON ASSEMBLY - STAINLESS STEEL
23 7003-093-001 FLOW RESTRICTOR - LOW-FLOW BUBBLER ONLY
24 7003-099-000 PUSHBUTTON
25 7003-830-000 UNIVERSAL MAINTENANCE TOOL
1
18
19
22
2
10

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAIN
A172-UG-VR-D1-BFS
Page 13 of 14
Revised: 06/01/2023 A
7020-988-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of
NOTE:
** Flow Restrictor Only Available
With Low Flow Bubbler.
A172-UG-VR-D1-BFS DRINKING FOUNTAIN PARTS BREAKDOWN
NOTE: See following page for fixture drawing corresponding to table of parts below.
Universal Maintenance Tool
-Button Removal
-Cartridge Retaining Nut
-Strainer Plug
-Removal of P.E. Tubing
from Push-in Fittings
33
5
4
2
3
1
13
15
9
17 15"
20
18
22
21
17 24"
23
33
22
21
17 24"
23
17 15"
7
7
6
4
3
2
1
8
9
10
14
13
19
11
12
20
11
12
16
17 2"
17 15"
21
24
25
26
27
28
29
26
30
25
31
32
VANDAL RESISTANT BUTTON &
VALVE BREAKDOWN
NOT TO SCALE

I N S TA L L AT I O N / M A I N T E N A N C E I N S T R U C T I O N S
DRINKING FOUNTAIN
A172-UG-VR-D1-BFS
Page 14 of 14
Revised: 06/01/2023 A
7020-988-001
MURDOCK MFG. • 15125 Proctor Avenue • City of Industry, CA 91746 USA
Phone [phone] or 626-333-2543 • Fax [phone] • www.murdockmfg.com Member of
A172-UG-VR-D1-BFS DRINKING FOUNTAIN PARTS BREAKDOWN TABLE
NOTE: See previous page for fixture drawing corresponding to table of parts below.
Repairs must be made with Murdock Manufacturing parts only. Please order through your local
representative or distributor.
ITEM # PART N UMBER DESCR IPTION
7003-001-199 BASIN TOP
7003-871-199 BASIN TOP w / Ø1/2"
7000-099-002 STAND ARD FLEXIBLE BU BBLER ASSEMBLY
7000-012-001 LEAD -FR EE STAINLESS STEEL BUBBLER ASSEMBLY
3 0124-008-000 #8 x 3/4" LG FLAT HD SELF TAPPING TOR X C/R SC REW
4 7000-006-000 FLAT DRAIN GASKET
5 7003-181-000 DRAIN TAILPIEC E (LONG)
6 7003-180-000 DRAIN ADAPTER
7 7003-184-000 7/8" SPRING CLAMP
8 7003-183-199 DRAIN HOSE
9 7003-950-199 HANGER BRACKET
7003-956-020 FILLER PLATE - GR AY
7003-825-199 FILLER PLATE - STAINLESS STEEL
11 7003-900-199 BACK PAN EL
12 7003-007-199 SUPPOR T STR UT
13 0124-036-000 #8 x 1/2" LONG TORX ROUND HEAD C/R SC REW
14 0124-050-000 #8 x 3/8" LONG PH ILLIPS PAN HEAD SC REW
15 1895-123-000 1/4" x 3/8" O.D . PUSH-IN SU PPLY INLET C ONNEC TION
16 1895-710-000 1/4" O.D . TUBE UN ION TEE (PU SH -IN )
17 2169-000-000 1/*4" O.D . PE TU BING (BLUE)
7003-955-020 RIGHT C ABIN ET - GR AY
7003-824-199 RIGHT C ABIN ET - STAINLESS STEEL
7003-954-020 LEFT CABINET - GR AY
7003-823-199 LEFT CABINET - STAINLESS STEEL
20 0124-031-000 #8 x 3/8" LONG SLOTTED HEX WASHER HEAD SC REW
21 7003-095-001 VALVE ASSEMBLY
7003-952-021 APRON ASSEMBLY - GR AY
7003-211-004 APRON ASSEMBLY - STAINLESS STEEL
23 7003-093-001 FLOW RESTRICTOR - LOW-FLOW BU BBLER ONLY
24 7003-198-199 (-VR) PU SH BU TTON MOU NTING SLEEVE
25 0124-055-000 #8 x 3/4" LONG PH ILLIPS ROU ND HEAD SC REW
26 0161-062-000 #6-32 x 1/2" LONG PH ILLIPS ROU ND HEAD SC REW
27 7003-195-000 (-VR) PU SH BU TTON OVERTRAVEL SPRING
28 7003-196-199 (-VR) PU SH BU TTON , CHROME
29 7003-197-199 (-VR) PU SH BU TTON ESC U TCHEON, CHR OME
30 7003-193-000 (-VR) PU SH BU TTON R ETURN SPR ING
31 7003-200-000 AUTO-STOP CONDESATION GASKET, LOWER
32 7003-199-000 AUTO-STOP CONDESATION GASKET, UPPER
33 7003-830-000 UNIVERSAL MAINTEN ANC E TOOL
1
18
19
22
2
10