Myson FINESSE User manual

heatingthroughinnovation.heatingthroughinnovation.
FINESSE.
INSTALLATION, OPERATING
& INSTRUCTION MANUAL
01.01.2014
MYSON Eastern Avenue, Team Valley, Gateshead, Tyne & Wear NE11 0PG, UK
T: 0845 402 3434, F: 0191 491 7568, [email protected], www.myson.co.uk
Please leave this manual with the end user.
Class 1 - 230V - 50 Hz
25796 Finesse Installation Manual A5 08/10/2013 13:00 Page 1

1.0 Warnings & Safety InformationContents
1.0 Warnings & Safety Information 03
2.0 General Information 05
3.0 Warranty 05
4.0 Installation 06
5.0 Maintenance, Repair & Disposal 07
6.0 Waste Disposal According to The WEEE Directive (2002/96/EC) 07
7.0 Operating Instructions 08
7.1 Stand Alone Radiator 08
7.2 Radiator Connected to a Wireless Wall Receiver & RF Programmer 09
7.3 Other Functions 10
8.0 Technical Characteristics 10
9.0 Optional Extra - RF Programmer 11
SAFETY INFORMATION
This appliance can be
used by children aged
from 8 years and above
and persons with reduced
physical, sensory or
mental capabilities or
lack of experience and
knowledge, if they have
been given supervision
or instruction concerning
use of the appliance in a
safe way and understand
the hazards involved.
Children shall not play with
the appliance. Cleaning
and user maintenance
shall not be made by
children unless they
are older than 8 and
supervised.
Keep the appliance and
its cord out of reach of
children aged less than
8 years.
Children of less than
3 years should be kept
away from the unit unless
continuously supervised.
Children aged from
3 years and less than
8 years shall only switch
on/off the appliance
provided that it has been
placed or installed in
its normal operating
position and they have
been given supervision
or instruction concerning
use of the appliance in a
safe way and understand
the hazards involved.
Children aged from
3 years and less than
8 years shall not plug in,
regulate, clean the
appliance or perform
user maintenance.
03FINESSE
25796 Finesse Installation Manual A5 08/10/2013 13:00 Page 3

05FINESSEFINESSE04
1.0 Warnings & Safety Information (cont...) 2.0 General Information
lThis appliance is a sealed electric radiator
designed for fixed wall-mounted installation.
lThis appliance conforms to the standards
EN 60 335-1 and EN 60 335-2-30.
lThis appliance is class 1 and splash resistant
(IP44).
lThis appliance complies with the European
Directive 2004/108/EC (CE Marking on all
appliances).
lThis unit is supplied complete with a
connection cable and wall brackets.
CAUTION
Some parts of this product
can become very hot and
cause burns. Particular
attention has to be given
where children and
vulnerable people are
present.
In order to avoid
overheating, do
not cover the radiator.
“Do not cover” means
that the radiator must
not be used for drying
clothes, for example,
by placing them directly
on the radiator.
IMPORTANT SAFETY
INSTRUCTIONS!
Before starting work disconnect power supply!
All installation work and wiring work related to
the radiators, thermostats and programmers
must be carried out only when de-energized.
The appliance should be installed by and
commissioned by qualified professionals only.
Make sure to adhere to valid safety regulations.
Any repairs or maintenance within the warranty
period should be carried out only by approved
service engineers confirmed by MYSON.
For the correct installation of radiators it is
essential that the fixing of the radiator is
carried out in such a way that it is suitable for
intended use AND predictable misuse. A
number of elements need to be taken into
consideration including the fixing method used
to secure the radiator to the wall, the type and
condition of the wall itself, and any additional
potential forces or weights, prior to finalising
installation. IN ALL CASES IT IS STRONGLY
RECOMMENDED THAT A SUITABLY
QUALIFIED PROFESSIONAL INSTALLER OR
SIMILAR TRADESPERSON CARRIES OUT
THE INSTALLATION.
PLEASE NOTE: The fixing materials provided are only
intended for installation on walls made of solid wood,
bricks, concrete or on timber-frame stud walls where the
fixing is into the timber. All walls being considered should
have no more than a maximum of 3mm wall finishing. For
walls made of other materials, for example hollow bricks,
please consult your installer and/or specialist supplier.
ONCE AGAIN, IF YOU ARE UNSURE, IT IS
STRONGLY RECOMMENDED THAT A SUITABLY
QUALIFIED PROFESSIONAL INSTALLER OR SIMILAR
TRADESPERSON CARRIES OUT THE INSTALLATION.
The radiator is equipped with an overheat
protection that cannot be reset (melt fuse). This
overheat protection disconnects the current if
the radiator becomes too hot (e.g. when
covered).
If the supply cord is damaged, it must be
replaced by the manufacturer, his service agent
or similar qualified persons in order to avoid a
hazard.
The radiator is filled with an exact amount of
environmental friendly vegetable oil. Any
repairs that require the radiator to be opened
shall therefore only be carried out by the
manufacturer or his approved agent. Please
contact MYSON in case of leakage.
3. Room Temperature Sensor
Cable Hook Assembly
Back of Radiator
3.0 Warranty
The product is covered by a 10 year warranty
except for the electrical and electronic
components that are covered by a 2 year
warranty.
2. Power On/Off Switch
1. Thermostat Control
4. Power Cable
25796 Finesse Installation Manual A5 08/10/2013 13:00 Page 5

07FINESSEFINESSE06
4.0 Installation 4.0 Installation (cont...)
lThis product is splash resistant with an IP44
rating. This must be considered when
installing in a location containing a bath or
shower, as defined by BS 7671.
lThe radiator may be positioned in zone 2
(figure 4) of the bathroom, in so far as no
operating controls (button, switch, etc.) are
in reach of persons in the bath or under
the shower.
FIXING
lMark out the distance between the brackets
and the positions for the screw holes as
shown in figure 2 and the dimension tables
at the top of page 7, and ensure the safety
clips are used (see figure 3).
A B
C
D
H
L
FLOOR
CONNECTION
lThe electrical installation must comply with
local or national regulations.
lThe radiator must be connected to the
electrical supply, using a switched fused
spur with 3mm separation on all poles.
lIf the radiator is installed in a bathroom or
shower room, it must be protected with a
residual current device (RCD) with a rated
residual current not exceeding 30 mA.
lThe radiator should be connected by a
suitable and qualified electrician. Please
refer to the wiring diagram (figure 5) for the
connection of the radiator.
C135 205
D90 163
Height (mm) 300 500
A109 160 160 160 160 160 160 160 160 160
B203 203 355 508 660 711 965 1016 1320 1727
Length (mm) 400 500 650 800 950 1000 1250 1300 1600 2000
FINESSE Double Panel (refer to figure 2)
Figure 2. Figure 3.
Figure 1.
Min.100mm
Min.100mm
Min.100mm
Step 1 Step 2
POSITIONING
lThe radiator must be positioned horizontally,
the right way up on the wall in order for it to
function correctly. Never switch the radiator
on in any other position as this will damage
the electrical element.
lThe radiator must be positioned according
to the applicable standards and the
minimum distances as specified in figure 1
should be carefully observed.
lThe radiator must not be located
underneath an electric socket.
Zone 1 Zone 2
Zone 2
Zone 0
OUTSIDE ZONES
3m 2.25m
0.6m
0.6m
Figure 4.
5.0 Maintenance, Repair & Disposal
lUse only a damp cloth for cleaning and
wiping of the radiator which should be
switched off at this time.
lWhen scrapping the radiator, follow the
regulations concerning the disposal of oil.
Figure 5.
6.0 Waste Disposal According to The WEEE Directive (2002/96/EC)
Waste disposal according to the
WEEE Directive (2002/96/EC).
The symbol on the product label
indicates that the product may
not be handled as domestic
waste, but must be sorted
separately. When it reaches the end of its
useful life, it shall be returned to a collection
facility for electrical and electronic products. By
returning the product, you will help to prevent
possible negative effects on the environment
and health to which the product can contribute
if it is disposed of as ordinary domestic waste.
For information about recycling and collection
facilities, you should contact your local
authority/municipality or refuse collection
service or the business from which you
purchased the product. Applicable to countries
where this Directive has been adopted.
Wire Colours
BR = Brown
BK = Black
BL = Blue
G/Y = Green/Yellow
Safety Clip-on Brackets
25796 Finesse Installation Manual A5 08/10/2013 13:00 Page 7

09FINESSEFINESSE08
7.2 Radiator Connected to a Wireless Wall Receiver & RF Programmer
7.1 Stand Alone Radiator
Select one of the following operation modes
using Dial D (figure 6):
COMFORT MODE
This mode is to be used during periods of
normal occupancy.
lRotate dial “D”
around to the (Sun)
symbol.
lSelect the desired
room temperature
between 5 and 37°C
(scale 1 to 6) using
dial “B”.
When connected to a wireless wall receiver
(figure 7), select the automatic operation
mode.
AUTOMATIC MODE
This mode is to be used during periods of
normal occupancy.
lSelect the desired
room temperature
during periods of
normal occupancy
between 5 and 37°C
(scale 1 to 6) using
dial “B”.
lRotate dial “D” within the area covered by
the (Clock) symbol. The value on this
scale indicates the desired temperature
reduction during the night or during shorter
periods of absence.
lWhen the house is unoccupied for longer
periods (e.g. holiday) you can override the
clock program by rotating dial “D” around
to “Reduced” or “Frost protection” mode.
REDUCED MODE
This mode is to be used at night-time or when
the house is unoccupied for a few hours or
more. This mode will lower the temperature of
the room by 3.5°C from the “Comfort mode”
set temperature.
lRotate dial “D”
around to the
(Moon) symbol.
FROST PROTECTION MODE
This mode is to be used when the house is
un-occupied for extended periods of time. The
lowest temperature the room can reach is 7°C.
lRotate dial “D”
around to the
(Snowflake) symbol.
Figure 7.
Wire Colours
BR = Brown
BK = Black
BL = Blue
G/Y = Green/Yellow
7.0 Operating Instructions
The On/Off button (see page 5) is located at
the bottom of the control side of the radiator.
The radiator should only be switched “on”
when it is correctly installed and secured to
the wall brackets. In the “on” position, LED A
(figure 6) turns green.
Figure 6.
A
B
C
D
E
RF Programmer
The MYSON FINESSE radiator can be used
as a stand alone radiator or can be
connected to radio frequency programmer
via a wireless wall receiver. Please refer to
section 9 for more information.
Optional Extras
25796 Finesse Installation Manual A5 08/10/2013 13:00 Page 9

11FINESSEFINESSE10
7.3 Other Functions
8.0 Technical Characteristics
lThe switch (E, figure 6) at the bottom of
the control panel can be used to limit the
output of the heating element in the front
panel and as a consequence the surface
temperature of the front panel.
60°C max.
75°C max.
90°C max.
When considering the permanent use of the
radiator at 60°C or 75°C maximum, the
following correction factor should be
applied for the output.
E.g. A 1000 Watt double panel with the switch
E on the position corresponding to 60°C will
deliver maximum 800 Watts. A 2000 Watt
double panel with the switch E on the position
corresponding to 75°C will deliver maximum
1800 Watts. These values should be considered
when selecting the number and type of panels
to cover the calculated heat losses.
lBoth LED indicators (A and C, figure 6)
indicate the working mode of the radiator.
Green Radiator switched on
Red Radiator heating
Red blinking Sensor problem
Off Comfort mode
Green blinking Reduced mode
(4 times-blank)
LED C (only when external programmer connected)
LED A
0.1°C
-10°C + 50°C
+5°C + 30°C
PWM
Class 1 – IP44
230 VAC – 50 Hz
~3.5 W
TRIAC 230 VAC 8A
lEN 60730-01
lEN 61000-6-1
lEN 61000-6-3
lEN 61000-4-2
lLV Directive 2006/95/CE
lEMC Directive 2004/108/CE
Measured temperature precision
Operating temperature
Setting temperature range
Control characteristics
Electrical protection
Power supply
Controls consumption
Output
The thermostat has been designed to
comply with the following Directives and
Standards.
60°C max ~0.80
75°C max ~0.90
90°C max 1
Surface
Temperature Double
panel
9.0 Optional Extra - RF Programmer
lInstall and plug the radiator into a
switched fused spur along with the wireless
wall receiver. NB: The RF programmer will
not work without the wireless wall receiver.
lInstall the RF programmer in a suitable
location.
lConnect the wireless wall receiver to the RF
programmer using the manufacturers
instructions on both products.
PLEASE REFER TO THE MANUFACTURERS
MANUAL FOR FULL INSTALLATION
INSTRUCTIONS.
Figure 8.
*When installing in a bathroom or wet room, please refer
to the installation positions in Section 4.0 Installation on
page 6.
Switched Fused Spur*
Wireless
Wall Receiver
RF Programmer
25796 Finesse Installation Manual A5 08/10/2013 13:00 Page 11