Myson ULOW-E2 Quick start guide

MYSON
heatingthroughinnovation.
PANEL RADIATORS.
heatingthroughinnovation.
MYSON
MYSON Eastern Avenue, Team Valley, Gateshead, Tyne & Wear NE11 0PG, UK
T: 0845 402 3434, F: 0191 491 7568, [email protected], www.myson.co.uk
TECHNICAL GUIDE
NOVEMBER 2013
26531 Tech Guide - Panels 07/11/2013 12:35 Page 1

In accordance with our policy of continual product improvement we reserve the right to amend the specification of these products or discontinue products without prior notification.
We have compiled the content of this literature to the best of our knowledge. Any typographical, clerical or other error or emission in any literature issued by us will be subject to
correction without liability being incurred by us. All rights reserved. No part of this document may be reproduced by any means without prior written consent.
Please note: due to print restrictions exact colour match is not always possible, however every effort has been made to ensure as much accuracy as possible.
1. ULOW-E2 04
lGeneral Specifications 05
lTechnical Information 06
lHeat Outputs & Accessories 07
2. FINESSE 08
lGeneral Specifications 09
lTechnical Information 10
lHeat Outputs & Technical Characteristics 11
3. PREMIER Compact 12
lGeneral Specifications 13
lTechnical Information 14
lHeat Outputs 18
4. PREMIER HE 12
lGeneral Specifications 13
lTechnical Information 15
lHeat Outputs 20
5. PREMIER Metric (2 & 4 Tap) 12
lGeneral Specifications 13
lTechnical Information 16
lHeat Outputs 22
6. SELECT Compact 12
lGeneral Specifications 13
lTechnical Information 17
lHeat Outputs 26
7. LST 28
lGeneral Specifications 29
lTechnical Information 30
lHeat Outputs 31
lControls 32
8. Heating Controls 33
lValves 34
03
Contents
Under the Construction Products Regulation, from 1st July 2013
all radiators listed in this technical guide will carry a CE mark.
26531 Tech Guide - Panels 07/11/2013 16:04 Page 3

General Specifications
Approval and Certification
All MYSON ULOW-E2 radiators are
manufactured and tested to BS EN 442. Every
radiator carries the BS Kitemark which
certifies independent approval of heat output
and verifies production under a quality system
to BS EN ISO 9001.
All MYSON ULOW-E2 radiators carry a two
year guarantee from date of manufacture
against defects caused by faulty materials or
manufacture.
Paint Finish
Every MYSON ULOW-E2 radiator is primer coated.
An epoxy polyester finishing coat in white (RAL 9016) is applied
to all front and rear surfaces allowing the radiator to be fitted
without further painting*.
Packaging
Every MYSON ULOW-E2 radiator is wrapped in paper and has
strong cardboard corners. The front side of the radiator is double
protected with an additional hard cardboard and then wrapped
together in shrink wrap. Each radiator is clearly labelled with size
and type, and packed with the appropriate number of brackets.
An assembly instruction, and instruction manual is also included.
Fixings
All MYSON ULOW-E2 radiators are supplied with concealed
wall mounting brackets. The table of dimensions gives further
details.
For the correct installation of radiators it is essential that the
fixing of the radiator is carried out in such a way that it is suitable
for intended use AND predictable misuse. A number of elements
need to be taken into consideration including the fixing method
used to secure the radiator to the wall, the type and condition of
the wall itself, and any additional potential forces or weights that
may happen to be applied to the radiator, prior to finalising
installation. IN ALL CASES IT IS STRONGLY RECOMMENDED
THAT A SUITABLY QUALIFIED PROFESSIONAL INSTALLER OR
SIMILAR TRADESPERSON CARRIES OUT THE INSTALLATION.
PLEASE NOTE: The fixing materials provided are only intended for installation on
walls made of solid wood, bricks, concrete or on timber-frame stud walls where the
fixing is into the timber. All walls being considered should have no more than a
maximum of 3mm wall finishing. For walls made of other materials, for example
hollow bricks, please consult your installer and/or specialist supplier. ONCE AGAIN,
IF YOU ARE UNSURE, IT IS STRONGLY RECOMMENDED THAT A SUITABLY
QUALIFIED PROFESSIONAL INSTALLER OR SIMILAR TRADESPERSON CARRIES
OUT THE INSTALLATION.
Application
MYSON ULOW-E2 radiators are for use on two pipe pumped
indirect domestic and commercial central heating installations,
with a maximum working temperature of 60oC. The system
should be designed in accordance with BS EN 12828:2003 or
BS EN 12831:2003 as appropriate, with particular care taken to
avoid air entry or water discharge.
We do not recommend the use of single feed indirect cylinders,
as the possibility of aeration due to water interchange may lead
to corrosion.
The installation work must be carried out in accordance with
recognised good practice, and precautions taken to avoid
contamination which could lead to corrosion. If a corrosion
inhibitor or other water treatment is to be used, the
Manufacturer’s Instructions must be strictly followed.
The recommendations of BS 7593, Code of Practice for
treatment of water in domestic hot water central heating
systems, should be followed where appropriate.
Safety Precautions
Radiators are hot when in use, and as such, present a risk of
burns to users on prolonged contact. The temperature of a
radiator is dependent on the temperature of the system water,
as set by the system installer or user. Installers and users should
ensure that those who may come into close proximity to hot
radiators are aware of the risk of burns. Installers and users
should take all necessary steps to minimise the risks of burns.
If the risk is significant, consideration should be given to
installing low surface temperature radiators, or to placing guards
in front of the radiators.
Electrical Data
All ULOW-E2 models require an electrical supply of 220-240V-
50Hz.
BS EN 442
2
2
2
*Specification is correct for white version only.
05
ULOW-E2 General Specifications
04 ULOW-E2
ULOW-E2
ULOW-E2.
Ultra efficient. Ultra stylish. Ultra intelligent.
lLow water temperature radiator
lIn-built fans for enhanced convection
lIntelligent controls
lRapid heat response
lCentral connection technology
lState of the art design
ULOW-E2
26531 Tech Guide - Panels 07/11/2013 12:35 Page 5

Model Height
(mm)
Length
(mm) Weight (kg) Water
Content (l) No. of Fans Comfort Boost Power
(W)
ULOW 040 600 400 17.13 2.84 2 20.3 30.7 3.5
ULOW 060 600 600 24.59 4.26 4 22.9 32.6 4.9
ULOW 080 600 800 32.06 5.68 6 24.4 33.7 6.4
ULOW 100 600 1000 39.7 7.10 8 25.4 34.4 7.8
ULOW 120 600 1200 47.16 8.52 10 26.3 35.1 9.3
ULOW 140 600 1400 53.02 9.94 12 26.9 35.6 10.8
ULOW 160 600 1600 62.27 11.36 14 27.5 36.0 12.1
Mounting Positions, Dimensions and Wall Brackets
Bracket Positions and Dimensions
Sound Pressure
(dBA) (at 2.5m)
B M8 B M6
A M8
A M6
66
141
600
100 100
Weight and Water Contents per Metre Length, Sound Levels and Motor Power
Sound levels tested in accordance with ISO 3741.
07
ULOW-E2 Heat Outputs & Accessories
06 ULOW-E2 Technical Information
The ULOW-E2 comes with a thermostatic radiator valve as standard. The twin entry valve and nut & olive pack should be purchased separately.
Order CodeProduct
Twin Entry Valve (Straight)
Twin Entry Valve (Angled)
Twin Entry Reversible Flow Valve (Straight)
Twin Entry Reversible Flow Valve (Angled)
Nut & Olive Pack (10mm)
Nut & Olive Pack (15mm)
E2TEVS
E2TEVA
E2TERVS
E2TERVA
E2NOP10
E2NOP15
E2TEVS
E2TEVA E2TERVS E2TERVA E2NOP10 / E2NOP15
Connections
All MYSON ULOW-E2 radiators are fitted with 4 x G ½ internal thread
and 2 x G ¾ external thread, underside centre. Thermostat valve top right
(can be swapped to top left).
Air Vents
An integral air vent is situated at the top right corner of each panel.
Operating Pressures
Every MYSON ULOW-E2 radiator is tested to a pressure of 10 bar and
is suitable for a working pressure of up to 13 bar.
Maximum operating temperature: 60°C (because of the fan units).
Nominal
Height
600 mm
ULOW-E2 - Type 22
(with factory fitted top grille and side panels)
400
600
800
1000
1200
1400
1600
Nominal
Length
(mm)
Static
Comfort
Boost
Static
Comfort
Boost
Static
Comfort
Boost
Static
Comfort
Boost
Static
Comfort
Boost
Static
Comfort
Boost
Static
Comfort
Boost
Operation
Mode
Heat Outputs
@ ΔT 10°C
Heat Outputs
@ ΔT 20°C
Heat Outputs
@ ΔT 30°C
Heat Outputs
@ ΔT 40°C
Heat Outputs
@ ΔT 50°C
Watts Btu/h Watts Btu/h Watts Btu/h Watts Btu/h Watts Btu/h
Order Code
(White)*
74 252 184 628 314 1071 459 1566 616 2102
125 427 272 928 430 1467 595 2030 766 2614 ULOW 040
147 502 317 1082 498 1699 686 2341 879 2999
111 379 276 942 471 1607 688 2347 923 3149
188 641 409 1396 647 2208 895 3054 1151 3927 ULOW 060
220 751 475 1621 746 2545 1027 3504 1316 4490
148 505 368 1256 628 2143 917 3129 1231 4200
250 853 545 1860 862 2941 1192 4067 1534 5234 ULOW 080
294 1003 634 2163 996 3398 1371 4678 1757 5995
185 631 460 1570 785 2678 1147 3914 1538 5248
312 1065 681 2324 1077 3675 1490 5084 1917 6541 ULOW 100
367 1252 792 2702 1244 4245 1712 5841 2194 7486
222 757 552 1883 942 3214 1376 4695 1846 6299
374 1276 817 2788 1292 4408 1787 6097 2299 7844 ULOW 120
440 1501 950 3241 1492 5091 2054 7008 2632 8980
259 884 644 2197 1099 3750 1605 5476 2153 7346
436 1488 953 3252 1507 5142 2085 7114 2682 9151 ULOW 140
514 1754 1109 3784 1741 5940 2398 8182 3073 10485
296 1010 736 2511 1256 4285 1834 6258 2461 8397
499 1703 1090 3719 1723 5879 2384 8134 3067 10465 ULOW 160
587 2003 1267 4323 1989 6786 2739 9345 3510 11976
*For the black model, simply add a ‘B’ to the end of the order code.
ULOW-E2
ULOW-E2
Accessories
Nominal Height
600
(mm)
143143
M6
157.5452.5
M8
B (mm) A (mm) B (mm)A (mm)
600mm Wall Bracket
Dimension Y =
Overall Length
2
26531 Tech Guide - Panels 07/11/2013 12:35 Page 7

FINESSE.
FINESSE
lNEW electric panel radiator
lAll the benefits of central heating, without the need for a plumbed in system
lSleek and modern control panel
lPrecision electronic thermostat
lFilled with environmentally friendly vegetable oil
lOptional extra: Radio frequency programmer for timed 24/7 control
09
FINESSE General Specifications
08 FINESSE
FINESSE
General Specifications
Approval and Certification
MYSON FINESSE electric panel radiators
are produced under a quality system to
BS EN ISO 9001.
MYSON FINESSE electric panel radiators
carry a ten year guarantee from date of
manufacture against defects caused by faulty
materials or manufacture except for the
electrical and electronic components that are
covered by a two year warranty.
Paint Finish
All FINESSE electric panel radiators are de-greased,
phosphated and primer coated. An epoxy polyester finishing
coat in white (RAL 9016) is applied to all front and rear surfaces
allowing the radiator to be fitted without further painting.
Packaging
Every MYSON FINESSE electric panel radiator is packed in
robust cardboard packaging specially designed to ensure that
the product reaches you in perfect condition. Each radiator is
clearly labeled with size and type, and packed with the
appropriate number of brackets.
Fixings
MYSON FINESSE electric panel radiators are supplied with
concealed wall mounting brackets. Please refer to the Bracket
Positions and Dimensions on page 10 for details. For the correct
installation of radiators it is essential that the fixing of the
radiator is carried out in such a way that it is suitable for
intended use AND predictable misuse. A number of elements
need to be taken into consideration including the fixing method
used to secure the radiator to the wall, the type and condition of
the wall itself, and any additional potential forces or weights that
may happen to be applied to the radiator, prior to finalising
installation. IN ALL CASES IT IS STRONGLY RECOMMENDED
THAT A SUITABLY QUALIFIED PROFESSIONAL INSTALLER OR
SIMILAR TRADESPERSON CARRIES OUT THE INSTALLATION.
PLEASE NOTE: The fixing materials provided are only intended for installation on
walls made of solid wood, bricks, concrete or on timber-frame stud walls where the
fixing is into the timber. All walls being considered should have no more than a
maximum of 3mm wall finishing. For walls made of other materials, for example
hollow bricks, please consult your installer and/or specialist supplier. ONCE AGAIN,
IF YOU ARE UNSURE, IT IS STRONGLY RECOMMENDED THAT A SUITABLY
QUALIFIED PROFESSIONAL INSTALLER OR SIMILAR TRADESPERSON CARRIES
OUT THE INSTALLATION.
Accessories
Touch up Paint
A handy 12ml container of touch up paint with
integral brush applicator in RAL 9016 is
available on request.
RF Programmer
The MYSON FINESSE radiator can be used as
a stand alone radiator or can be connected to
a radio frequency programmer via a wireless
wall receiver.
Application
All installation work and wiring work related to the radiators,
thermostats and programmers must be carried out only when
de-energized. The appliance should be commissioned by
qualified professionals only. Make sure to adhere to valid safety
regulations. Any repairs or maintenance within the warranty
period should be carried out only by approved service engineers
confirmed by MYSON.
Safety Precautions
Some parts of this product can become very hot and cause
burns. Particular attention has to be given where children and
vulnerable people are present. Installers and users should take
all necessary steps to minimise the risks of burns. If the risk is
significant, consideration should be given to placing guards in
front of the radiators.
In order to avoid overheating, do not cover the radiator. “Do not
cover” means that the radiator must not be used for drying
clothes, for example, by placing them directly on the radiator.
BS EN 442
2
2
2
Available from
1st January 2014
26531 Tech Guide - Panels 07/11/2013 12:35 Page 9

11
FINESSE Heat Outputs & Technical Characteristics
10 FINESSE Technical Information
FINESSE
FINESSE
Weight per Radiator (Packed)
lMYSON FINESSE is a sealed electric radiator designed for
fixed wall-mounted installation.
lMYSON FINESSE conforms to the standards EN 60 335-1
and EN 60 335-2-30.
lMYSON FINESSE is class 2 and splash resistant (IP44).
lMYSON FINESSE complies with the European Directive
2004/108/EC (CE Marking on all appliances).
Length (mm)
Height 400 500 650 800 950 1000 1250 1300 1600 2000
300 N/A 10.5 N/A 16.5 N/A 20.5 N/A 25.5 31.5 38.5
500 14.0 17.0 21.5 25.5 29.5 N/A 39.1 N/A N/A N/A
Mounting Positions, Dimensions and Wall Brackets
Bracket Positions and Dimensions
Technical Characteristics Optional Extra - RF Programmer
Waste Disposal According to The WEEE Directive (2002/96/EC)
Safety Clip-on Brackets
300 500
135
90
205
163
Nominal
Height (mm)
C
D
400 500 650 800 950 1000 1250 1300 1600 2000
109 160 160 160 160 160 160 160 160 160
203 203 355 508 660 711 965 1016 1320 1727
Nominal
Length (mm)
A
B
A B
C
D
H
L
Waste disposal according to the WEEE Directive
(2002/96/EC). The symbol on the product label
indicates that the product may not be handled as
domestic waste, but must be sorted separately.
When it reaches the end of its useful life, it shall be
returned to a collection facility for electrical and
electronic products. By returning the product, you will help to
prevent possible negative effects on the environment and health
to which the product can contribute if it is disposed of as ordinary
domestic waste. For information about recycling and collection
facilities, you should contact your local authority/municipality or
refuse collection service or the business from which you
purchased the product. Applicable to countries where this
Directive has been adopted.
Nominal Height
300 mm
FINESSE
Double Panel “Xtra”
500
800
1000
1300
1600
2000
Nominal Length
(mm)
Heat Outputs
(Rated Watts) Order Code
500 FE 30 DX 50
750 FE 30 DX 80
1000 FE 30 DX 100
1250 FE 30 DX 130
1500 FE 30 DX 160
2000 FE 30 DX 200
Nominal Height
500 mm
400
500
650
800
950
1250
500 FE 50 DX 40
750 FE 50 DX 50
1000 FE 50 DX 65
1250 FE 50 DX 80
1500 FE 50 DX 95
2000 FE 50 DX 125
0.1°C
-10°C + 50°C
+5°C + 30°C
PWM
Class 1 – IP44
230 VAC – 50 Hz
~3.5 W
TRIAC 230 VAC 8A
lEN 60730-01
lEN 61000-6-1
lEN 61000-6-3
lEN 61000-4-2
lLV Directive
2006/95/CE
lEMC Directive
2004/108/CE
Measured temperature precision
Operating temperature
Setting temperature range
Control characteristics
Electrical protection
Power supply
Controls consumption
Output
The thermostat has been
designed to comply with the
following Directives and
Standards.
lInstall and plug the radiator into a switched fuse spur along
with the wireless wall receiver. NB: The RF programmer will
not work without the wireless wall receiver.
lInstall the RF programmer in a suitable location.
lConnect the wireless wall receiver to the RF programmer
using the manufacturers instructions on both products.
PLEASE REFER TO THE MANUFACTURERS MANUAL FOR
FULL INSTALLATION INSTRUCTIONS.
Switched Fuse Spur*
RF Programmer
Wireless
Wall
Receiver
Wall
.
.
.
.
Wall
500mm Wall Bracket
300mm Wall Bracket
Step 1 Step 2
*When installing in a bathroom or wet room, please refer to the FINESSE
Installation, Operating & Instruction Manual.
26531 Tech Guide - Panels 07/11/2013 12:35 Page 11

PREMIER & SELECT
13
PREMIER & SELECT General Specifications
12 PREMIER & SELECT
General Specifications
Approval and Certification
All MYSON Panel radiators are manufactured
and tested to BS EN 442. Every radiator
carries the BS Kitemark which certifies
independent approval of heat output and
verifies production under a quality system
to BS EN ISO 9001.
All MYSON Panel radiators carry a ten year
guarantee from date of manufacture against
defects caused by faulty materials or
manufacture.
Paint Finish
Every MYSON Panel radiator is de-greased, phosphated and
primer coated.
An epoxy polyester finishing coat in white (RAL 9016) is applied
to all front and rear surfaces allowing the radiator to be fitted
without further painting.
Packaging
Every MYSON Panel radiator has plastic corner protection with
durable cardboard edge packaging as well as being fully
wrapped in strong polythene. Each radiator is clearly labelled
with size and type, and packed with the appropriate number of
brackets.
Fixings
All MYSON Panel radiators are supplied with concealed wall
mounting brackets. The table of dimensions gives further details.
For the correct installation of radiators it is essential that the
fixing of the radiator is carried out in such a way that it is suitable
for intended use AND predictable misuse. A number of elements
need to be taken into consideration including the fixing method
used to secure the radiator to the wall, the type and condition of
the wall itself, and any additional potential forces or weights that
may happen to be applied to the radiator, prior to finalising
installation. IN ALL CASES IT IS STRONGLY RECOMMENDED
THAT A SUITABLY QUALIFIED PROFESSIONAL INSTALLER OR
SIMILAR TRADESPERSON CARRIES OUT THE INSTALLATION.
PLEASE NOTE: The fixing materials provided are only intended for installation on
walls made of solid wood, bricks, concrete or on timber-frame stud walls where the
fixing is into the timber. All walls being considered should have no more than a
maximum of 3mm wall finishing. For walls made of other materials, for example
hollow bricks, please consult your installer and/or specialist supplier. ONCE AGAIN,
IF YOU ARE UNSURE, IT IS STRONGLY RECOMMENDED THAT A SUITABLY
QUALIFIED PROFESSIONAL INSTALLER OR SIMILAR TRADESPERSON CARRIES
OUT THE INSTALLATION.
Accessories
Touch up Paint
A handy 12ml container of touch up paint with integral brush
applicator in RAL 9016 is available on request.
Air Vent Key
An alloy key for bleeding and venting is available on request.
Order Code: PREMRADKEY
Application
MYSON Panel radiators are for use on two pipe pumped
indirect domestic and commercial central heating installations,
with a maximum working temperature of 100oC. The system
should be designed in accordance with BS EN 12828:2003 or
BS EN 12831:2003 as appropriate, with particular care taken to
avoid air entry or water discharge.
We do not recommend the use of single feed indirect cylinders,
as the possibility of aeration due to water interchange may lead
to corrosion.
The installation work must be carried out in accordance with
recognised good practice, and precautions taken to avoid
contamination which could lead to corrosion. If a corrosion
inhibitor or other water treatment is to be used, the
Manufacturer’s Instructions must be strictly followed.
The recommendations of BS 7593, Code of Practice for
treatment of water in domestic hot water central heating
systems, should be followed where appropriate.
Safety Precautions
Radiators are hot when in use, and as such, present a risk of
burns to users on prolonged contact. The temperature of a
radiator is dependent on the temperature of the system water,
as set by the system installer or user. Installers and users should
ensure that those who may come into close proximity to hot
radiators are aware of the risk of burns. Installers and users
should take all necessary steps to minimise the risks of burns.
If the risk is significant, consideration should be given to
installing low surface temperature radiators, or to placing guards
in front of the radiators.
Heat Output
Careful design of an optimum profile for the convector plate,
and welding directly onto the wet and dry sections of the
radiator, have combined to give high heat output per surface
area of radiator.
The heat outputs shown in the table below are based on a mean
water to air temperature difference of 50oC. When the
difference is not 50oC, the output should be multiplied by the
appropriate factor from within the table:
BS EN 442
Centigrade Factor Fahrenheit
Example:
Heat emission required: 2000 Watts
Room air temperature required: 20oC
Mean water temperature in radiator: 65oC
1. Temperature difference = 65-20 = 45oC
2. From Factor Table 45oC gives a factor of: 0.87
3. Divide required heat emission
by factor = 2000 = 2298 Watts
4. From selection tables choose any
radiator rated at 2298 Watts or more.
0.87
20°C 0.30 36°F
25°C 0.41 45°F
30°C 0.51 54°F
35°C 0.63 63°F
40°C 0.75 72°F
45°C 0.87 81°F
50°C 1.00 90°F
55°C 1.13 99°F
60°C 1.27 108°F
65°C 1.41 117°F
70°C 1.55 126°F
PREMIER & SELECT
PREMIER & SELECT.
Standard, Compact & Metric.
l2 and 4 tap connections
lStylish and safety conscious round top designs
lHuge choice of styles and sizes
lSingle, double and triple convectors available
lHigh quality white gloss paint finish
PREMIER HE
SELECT Compact
26531 Tech Guide - Panels 07/11/2013 12:35 Page 13

15
PREMIER HE (Imperial) Technical Information
14 PREMIER Compact Technical Information
Weight and Water Contents per Metre Length
Connections
All MYSON PREMIER Compact radiators are fitted with 4 - 1 /2inch
BSP connections.
Air Vents
An air vent and plug are packed with every radiator.
Operating Pressures
Every MYSON PREMIER Compact radiator is tested to a pressure
of 7 bar (101.5 psi) and is suitable for a working pressure of up to
5.4 bar (78 psi).
Height (mm)
Type
300 450 600 700
Weight (kg) Water
Content (l) Weight (kg) Water Content (l) Weight (kg) Water Content (l) Weight (kg) Water Content (l)
11 SC 9.4 2.8 13.6 3.4 18.4 4.1 21.3 4.9
21 DPX 15.4 5.7 22.2 6.7 29.2 8.3 33.8 9.9
22 DC 18.5 5.7 25.7 6.7 34.7 8.3 40.2 9.9
Mounting Positions, Dimensions and Wall Brackets
A
(mm)
B
(mm)
245
395
545
645
170
237
320
410
Nominal
Height (mm)
300
450
600
700
N.B. Long leg suitable
for hanging Type 11
(SC) radiators only.
Short leg suitable for
radiator Types 11, 21
& 22.
N.B. Figures in brackets apply when hanging with long leg.
D
143 143
C
E
Bracket Positions and Dimensions
Bracket Plan View
52
37
SC
79 (94)
A
31
45 (60) 100Min
DPX
111
A
31
70 100 Min
DC
135
A
31
83 100Min
B B B
(View from back of radiator)
C
(mm)
D
(mm)
300
450
600
700
70
137
220
310
Nominal
Height (mm)
300
450
600
700
E
(mm)
762
864
Nominal
Length (mm)
1800
2000
N.B. Only radiators 1800mm & 2000mm long have
3 sets of brackets as shown, with the 3rd set in the
middle of the radiator.
Height (in)
Type
12
Weight
per Section
Water Content
per Section
(kg) (l)
15
Weight
per Section
Water Content
per Section
(kg) (l)
21
Weight
per Section
Water Content
per Section
(kg) (l)
27
Weight
per Section
Water Content
per Section
(kg) (l)
11 SC 0.37 0.14 0.49 0.16 0.69 0.20 0.90 0.25
21 DPX 0.84 0.32 1.18 0.41 1.54 0.49
22 DC 0.74 0.29 0.97 0.32 1.38 0.41 1.81 0.49
Weight and Water Contents per Section
Mounting Positions, Dimensions and Wall Brackets
*Available for full range **Available for selected sizes
Bracket Positions and Dimensions
Connections
All MYSON PREMIER HE radiators are fitted with 2 - 1 /2inch BSP
connections. Selected sizes are available with 4 - 1
/2inch BSP connections,
please refer to size guide, pages 20-21.
Air Vents
An integral air vent is situated at the top right-hand corner of each panel.
Operating Presssures
Every MYSON PREMIER HE radiator is tested to a pressure of 7 bar
(101.5 psi) and is suitable for a working pressure of up to 5.4 bar (78 psi).
CD
11.8 300
15.4 390
20.9 530
27.2 690
2.75 70
3.03 77
5.91 150
12.20 310
Nominal
Height (in)
12
15
21
27
(in) (mm) (in) (mm)
AB
6.65 170
6.93 177
9.81 250
16.10 410
N/A N/A
13.2 335
18.7 475
25.0 635
Nominal
Height (in)
12
15
21
27
(in) (mm) (in) (mm)
E
34 864
35 889
38 965
Nominal
Length (in)
77
79
85
(in) (mm)
N.B. Radiators up to and including 69" long have two brackets. Radiators 77" and longer
have three brackets. The position of the centre bracket is given in the above table.
D
143 143
C
E
Bracket Plan View
52
37
N.B. Figures in brackets apply
when hanging with long leg.
Long leg suitable for hanging
Type 11 (SC) radiators only.
Short leg suitable for radiator
Types 11, 21 & 22.
SC
79 (94)
31
45 (60) 100Min
3.1" (3.7")
3.9"
1.8"(2.4")
1.2"
DPX
111
31
70 100Min
4.4"
3.9"
2.8"
1.2"
DC
135
31
83 100Min
5.3"
3.9"
3.3"
1.2"
AAA
SC
79 (94)
B
31
45 (60) 100Min
3.1" (3.7")
3.9"
1.8"(2.4")
1.2"
DPX
111
B
31
70 100Min
4.4"
3.9"
2.8"
1.2"
DC
135
B
31
83 100Min
5.3"
3.9"
3.3"
1.2"
A A A
2 connections*
4 connections**
(View from back of radiator)
PREMIER HE
PREMIER COMPACT
† †
† 118mm from
each end for 11"
(286mm) long
radiators only.
Wall
.
.
.
.
Wall
450/600/700mm Wall Bracket
300mm Wall Bracket
Wall
.
.
.
.
Wall
15/21/27" Wall Bracket
12" Wall Bracket
26531 Tech Guide - Panels 07/11/2013 12:35 Page 15

17
SELECT Compact Technical Information
16 PREMIER Metric (2 & 4 Tap) Technical Information
Height (mm)
Type
300
Weight Water
Content
(kg) (l)
Weight and Water Contents per Metre Length
Mounting Positions, Dimensions and Wall Brackets
Bracket Positions and Dimensions
Connections
All MYSON PREMIER Metric radiators are fitted with 2 - 1 /2inch BSP
connections. Selected sizes are available with 4 - 1
/2inch BSP connections,
please refer to size guide, pages 22-23 and 24-25.
Air Vents
An integral air vent is situated at the top right-hand corner of each panel.
Operating Pressures
Every MYSON PREMIER Metric radiator is tested to a pressure of 7 bar
(101.5 psi) and is suitable for a working pressure of up to 5.4 bar (78 psi).
CD
300 70
450 137
600 220
700 310
Nominal
Height (mm)
300
450
600
700
(mm) (mm)
AB
170 243
237 393
320 543
410 643
Nominal
Height (mm)
300
450
600
700
(mm) (mm)
E
762
864
965
1067
1168
1270
1372
Nominal
Length (mm)
1800
2000
2200
2400
2600
2800
3000
(mm)
450
Weight Water
Content
(kg) (l)
600
Weight Water
Content
(kg) (l)
700
Weight Water
Content
(kg) (l)
N.B. Radiators up to and including 1600mm long have two brackets. Radiators 1800mm and
longer have three brackets. The position of the centre bracket is given in the above table.
SC
79 (94)
31
45 (60) 100Min
DPX
111
31
70 100Min
DC
135
31
83 100Min
A A A
SC
79 (94)
B
31
45 (60) 100Min
DPX
111
B
31
70 100Min
DC
135
B
31
83 100Min
A A A
Bracket Plan View
52
37
N.B. Figures in brackets apply
when hanging with long leg.
Long leg suitable for hanging
Type 11 (SC) radiators only.
Short leg suitable for radiator
Types 11, 21 & 22.
11 SC 7.4 2.8 11.6 3.4 15.7 4.1 18.4 4.9
21 DPX 13.0 5.7 20.0 6.7 26.7 8.3 31.2 9.9
22 DC 14.8 5.7 23.1 6.7 31.3 8.3 36.7 9.9
2 connections
4 connections
D
143 143
C
E
(View from back of radiator)
Mounting Positions, Dimensions and Wall Brackets
Height (mm)
Type
300
Weight
(kg)
Water
Content (l)
Weight and Water Contents per Metre Length
Connections
All MYSON SELECT Compact radiators are fitted with 4 - 1 /2inch BSP
connections.
Air Vents
An air vent and plug are packed with every radiator.
Operating Pressures
Every MYSON SELECT Compact radiator is tested to a pressure of
10.5 bar (152.5 psi) and is suitable for a working pressure of up to 8.0 bar
(117.1 psi).
Bracket Positions and Dimensions
C
(mm)
Nominal
Height (mm)
A
(mm)
B
(mm)
Nominal
Height (mm)
400
Weight
(kg)
Water
Content (l)
450
Weight
(kg)
Water
Content (l)
500
Weight
(kg)
Water
Content (l)
600
Weight
(kg)
Water
Content (l)
700
Weight
(kg)
Water
Content (l)
11G SSG 8.4 1.7 11.2 2.1 N/A N/A 13.8 2.6 16.7 3.0 19.3 3.5
21G SXG 14.1 3.4 18.7 4.3 N/A N/A 23.2 5.2 27.9 6.2 32.3 7.0
22G SDG 15.8 3.4 21.2 4.3 N/A N/A 26.6 5.2 32.0 6.2 37.3 7.0
33G STG 24.5 5.1 N/A N/A 37.4 7.5 N/A N/A 50.2 9.8 N/A N/A
Type 11 Type 21 Type 22 Type 33
Wall Brackets
A
100
Min
69
170
152
158
Min
A
100
Min
78
129
102
190
Min
A
100
Min
62
97
70
190
Min
100
Min
A
78
46
62
190
Min
100
C
83
117
150
1800 & above = (L/ 2) - 50mm
150
117
83
1800 & above = (L/ 2) - 17mm
1800 & above = (L/ 2) + 17mm
L
100
133.3
166.6
1800 & above = L/ 2
166.6
133.3
100
1800 & above = (L/ 2) + 33mm
1800 & above = (L/ 2) - 33mm
L
Type 11
Type 21, 22 & 33
Supplied with Type 11,21, 22 Supplied with Type 33 only
300
400
450
500
600
700
250
350
400
450
550
650
142
242
292
342
442
542
300
400
450
500
600
700
120
220
270
320
420
520
WALL
23
32
14
22.5
22.5
79
10
B+11
12
15
32.5
Type 21 & 22
WALL
23
SS
9.6
5.6
WALL
B
24
22
39
17
69
32
SX
&
SD
14. 6
Type 11
only Fixing Hole Dimensions Type 33 only
SELECT COMPACT
PREMIER METRIC
Wall
.
.
.
.
Wall
450/600/700mm Wall Bracket
300mm Wall Bracket
26531 Tech Guide - Panels 07/11/2013 12:35 Page 17

Single Convector - Type 11
(with factory fitted top grille and side panels)
Double Panel “Xtra” - Type 21
(with factory fitted top grille and side panels)
Double Convector - Type 22
(with factory fitted top grille and side panels)
272 927 141 480 45 SC 40 G
343 1171 178 607 45 SC 50 G
415 1416 215 733 45 SC 60 G
486 1657 252 859 45 SC 70 G
557 1902 289 985 45 SC 80 G
628 2144 325 1110 45 SC 90 G
700 2388 363 1237 45 SC 100 G
771 2632 400 1363 45 SC 110 G
842 2874 436 1489 45 SC 120 G
985 3360 510 1741 45 SC 140 G
1128 3849 584 1994 45 SC 160 G
1271 4335 658 2246 45 SC 180 G
1413 4822 732 2497 45 SC 200 G
354 1210 182 621 60 SC 40 G
448 1528 230 785 60 SC 50 G
541 1847 278 949 60 SC 60 G
634 2163 326 1111 60 SC 70 G
727 2482 374 1275 60 SC 80 G
820 2797 421 1437 60 SC 90 G
913 3116 469 1601 60 SC 100 G
1007 3435 517 1764 60 SC 110 G
1099 3750 565 1926 60 SC 120 G
1285 4385 660 2252 60 SC 140 G
1472 5023 756 2580 60 SC 160 G
1658 5657 852 2906 60 SC 180 G
1844 6291 947 3232 60 SC 200 G
300 1023 152 520 70 SC 30 G
411 1404 209 714 70 SC 40 G
520 1774 264 902 70 SC 50 G
628 2144 320 1090 70 SC 60 G
736 2510 374 1276 70 SC 70 G
844 2880 429 1465 70 SC 80 G
951 3246 484 1651 70 SC 90 G
1060 3616 539 1839 70 SC 100 G
1168 3986 594 2027 70 SC 110 G
1276 4352 649 2214 70 SC 120 G
1491 5089 758 2588 70 SC 140 G
1708 5829 869 2964 70 SC 160 G
796 2715 418 1425 45 DPX 80 G
897 3060 471 1606 45 DPX 90 G
999 3409 524 1789 45 DPX 100 G
1101 3757 578 1972 45 DPX 110 G
1202 4103 631 2153 45 DPX 120 G
1406 4797 738 2517 45 DPX 140 G
1610 5494 845 2883 45 DPX 160 G
1814 6188 952 3247 45 DPX 180 G
491 1674 254 865 60 DPX 40 G
620 2116 320 1093 60 DPX 50 G
749 2557 387 1321 60 DPX 60 G
877 2994 453 1547 60 DPX 70 G
1007 3435 520 1775 60 DPX 80 G
1135 3872 586 2001 60 DPX 90 G
1264 4313 653 2229 60 DPX 100 G
1394 4755 720 2457 60 DPX 110 G
1522 5192 786 2683 60 DPX 120 G
1779 6070 919 3137 60 DPX 140 G
2038 6953 1053 3593 60 DPX 160 G
2295 7831 1186 4046 60 DPX 180 G
2552 8709 1319 4500 60 DPX 200 G
561 1915 288 983 70 DPX 40 G
709 2419 364 1242 70 DPX 50 G
857 2924 440 1501 70 DPX 60 G
1003 3424 515 1758 70 DPX 70 G
1151 3928 591 2017 70 DPX 80 G
1298 4428 666 2274 70 DPX 90 G
1446 4933 742 2533 70 DPX 100 G
1594 5437 818 2792 70 DPX 110 G
1740 5937 893 3048 70 DPX 120 G
2034 6941 1045 3564 70 DPX 140 G
2330 7950 1196 4082 70 DPX 160 G
518 1767 267 912 45 DC 40 G
654 2232 338 1152 45 DC 50 G
791 2698 408 1392 45 DC 60 G
926 3159 478 1630 45 DC 70 G
1062 3625 548 1871 45 DC 80 G
1198 4086 618 2108 45 DC 90 G
1334 4552 688 2349 45 DC 100 G
1470 5017 759 2589 45 DC 110 G
1606 5478 829 2827 45 DC 120 G
1877 6405 969 3305 45 DC 140 G
2150 7336 1110 3786 45 DC 160 G
2422 8263 1250 4264 45 DC 180 G
2693 9190 1390 4742 45 DC 200 G
662 2258 335 1144 60 DC 40 G
836 2853 424 1446 60 DC 50 G
1011 3448 512 1747 60 DC 60 G
1183 4037 600 2046 60 DC 70 G
1358 4633 688 2348 60 DC 80 G
1530 5222 776 2646 60 DC 90 G
1705 5817 864 2948 60 DC 100 G
1879 6412 952 3249 60 DC 110 G
2052 7001 1040 3548 60 DC 120 G
2399 8186 1216 4148 60 DC 140 G
2748 9376 1393 4751 60 DC 160 G
3095 10560 1568 5351 60 DC 180 G
3442 11745 1744 5952 60 DC 200 G
545 1861 274 934 70 DC 30 G
746 2546 375 1278 70 DC 40 G
943 3217 473 1615 70 DC 50 G
1139 3888 572 1952 70 DC 60 G
1334 4552 670 2285 70 DC 70 G
1531 5223 769 2622 70 DC 80 G
1726 5888 866 2956 70 DC 90 G
1922 6559 965 3293 70 DC 100 G
2119 7230 1064 3630 70 DC 110 G
2314 7894 1162 3963 70 DC 120 G
2705 9229 1358 4634 70 DC 140 G
3098 10571 1556 5307 70 DC 160 G
Nominal Length (mm - inches)
400 - 16
500 - 20
600 - 24
700 - 28
800 - 31
900 - 35
1000 - 39
1100 - 43
1200 - 47
1400 - 55
1600 - 63
1800 - 71
2000 - 79
400 - 16
500 - 20
600 - 24
700 - 28
800 - 31
900 - 35
1000 - 39
1100 - 43
1200 - 47
1400 - 55
1600 - 63
1800 - 71
2000 - 79
286 - 11
438 - 17
540 - 21
641 - 25
743 - 29
844 - 33
946 - 37
1047 - 41
1149 - 45
1352 - 53
1556 - 61
1759 - 69
300 - 12
400 - 16
500 - 20
600 - 24
700 - 28
800 - 31
900 - 35
1000 - 39
1100 - 43
1200 - 47
1400 - 55
1600 - 63
19
PREMIER Compact Heat Outputs
18 PREMIER Compact Heat Outputs
Heat Outputs
@ ΔT 50°C
Heat Outputs
@ ΔT 30°C
Watts Btu/h Watts Btu/h
Order Code
Heat Outputs
@ ΔT 50°C
Heat Outputs
@ ΔT 30°C
Watts Btu/h Watts Btu/h
Order Code
Heat Outputs
@ ΔT 50°C
Heat Outputs
@ ΔT 30°C
Watts Btu/h Watts Btu/h
Order Code
400 - 16
800 - 31
1000 - 39
1200 - 47
1600 - 63
2000 - 79
353 1206 186 636 30 DC 40 G
725 2473 382 1305 30 DC 80 G
910 3106 480 1638 30 DC 100 G
1096 3738 578 1972 30 DC 120 G
1467 5006 774 2641 30 DC 160 G
1838 6271 969 3308 30 DC 200 G
584 1991 313 1067 30 DPX 80 G
882 3009 473 1612 30 DPX 120 G
1181 4030 633 2159 30 DPX 160 G
191 652 99 339 30 SC 40 G
392 1338 204 695 30 SC 80 G
593 2023 308 1051 30 SC 120 G
794 2709 412 1407 30 SC 160 G
994 3393 516 1762 30 SC 200 G
N.B. The tabulated heat outputs are quoted at a mean water to air temperature difference of 50oC and 30oC.
PREMIER COMPACT
PREMIER COMPACT
Nominal Height
300mm
Nominal Height
450mm
Nominal Height
600mm
Nominal Height
700mm
26531 Tech Guide - Panels 07/11/2013 12:35 Page 19