NANLITE MixPanel 60 User manual

Guangdong NanGuang Photo&Video Systems Co., Ltd
USER MANUAL
MixPanel 60/MixPanel 150
RGBWW LED PANEL LIGHT

1
MixPanel 60/MixPanel 150 RGBWW LED Panel Light
Product Show
Model: MixPanel 60
LED Power: 60W x 5
Power Input: 15V power adapter or
14.8V Sony V-mount battery(Not Included)
Color Temperature: 2700K - 7500K
CRI(Ra): 98
Model: MixPanel 150
LED Power: 150W x 5
Power Input: 24V power adapter or
26V Sony V-mount Battery(Not Included)
Color Temperature: 2700K - 7500K
CRI(Ra): 98
Technical Data
MixPanel
MixPanel

SELECT
MixPanel
CCT HSI RGBW GEL
EFFECT PRESET MENU LOCK
1.Connection between light fixture and power adapter. 2.Connection between light fixture and battery.
HSI RGBW GEL
PRESET MENU LOCK
MixPanel
SELECT
MixPanel
HSI RGBW GEL
PRESET MENU LOCK
battery
14.8V
battery
26V
Variable Power Options
MixPanel MixPanel
MixPanel
2
CCT HSI RGBW GEL
EFFECT PRESET MENU LOCK
SELECT
MixPanel
MixPanel

Barndoor Installation Instruction
Product Details
2. USB port
3. DMX IN
4. DMX OUT
1. Yoke
5. Battery lock button
6. Battery holder
7. Angle fixing knob
8. Fixture body handle
9. User interface
10. Power indicator
11. Power switch
12. DC IN
13. Bracket fixing knob
When installing the barndoor, make sure
its mounts point line up with the slots on
the light fixture. Now, snap in structure rods
of barndoor into fastener slot on light fixture.
When removing the barndoor, remove the
safety rope lock first, then pull the barndoor
away from fixture.
Note: when installing and removing the barndoor, please do not touch the diffuser on the front of light fixture to avoid surface scratches.
Fix the safety rope lock on the screw hole
on the light fixture.
3

4
1. Power Connection
①When connecting the power supply, please make sure the power, voltage and frequency is consistent with the provided power supply.
②When using a v-mount battery, please make sure to turn off the fixture and then plug in the battery.
Note: （1）Please do not use too much force when installing the battery properly.
（2）When removing the battery, make sure to press the battery unlock button to remove battery properly.
1. Yoke: For connecting the fixture to the light stand and adjusting the tilt and pan of fixture.
2. USB port: For updating controller firmware.
3. DMX IN: DMX signal input interface.
4. DMX OUT: DMX signal output interface.
5. Battery lock button: For installing and removing the battery.
6. Battery holder: For installing V-Mount battery (Not Included).
7. Angle fixing knob: For adjusting and fixing the tilt angle of fixture.
8. Fixture body handle: To lift the fixture and adjust the direction of the light.
9. User interface: For displaying & controlling various function operations and data.
10. Power indicator: For checking the status of the power input. If the indicator is always on, it means normal power supply; if the indicator is flashing or off, it means
abnormal power supply or no power input.
11. Power switch: For on/off the fixture.
12. DC IN: DC power input interface.
13. Bracket fixing knob: For connecting the fixture on a light stand.
Product Details
Usage
MixPanel60/MixPanel150 is designed to work with a 2.4G remote controller or Nanlite WIFl-APP via WIFl transfer device to control light remotely.
NOTE: 2.4G remote controller or WiFi transfer device sold separately. (See separate instructions for remote controller or Wi-Fi transfer device)
2. 2.4G Wireless Remote Control
4+
3+
1-
2-
1-
2-
4+
3+
DC IN

5
DMX IN DMX OUT
1 GND
2 DATA-
3 DATA+
NC
NC
NC
NC
GND 1
DATA- 2
DATA+ 3
3. DMX lighting console connection
NOTE: DMX cable should be bought additionally for connecting the MixPanel to a DMX lighting console.
5. DMX Start Address Setting
When using a DMX console to control the fixture, each one must be set to its own DMX address, to receive the dimmer signal and response correctly. The fixture
has total 2 DMX modes, accept DMX512 national standard signal.
Mode 1: Total 12 channels, set the first fixture's DMX start address to 001, 013 for the second one displays, 025 for the third one and so on.
4. DMX-In Port
In DMX mode, make sure the last light is the only light with cable connected to DMX output. There is a resistance
about 120 (OHM) between the second pin and third pin of this plug (as below photo). Make sure this plug is installed
into the output of last fixture which can avoid noise and reflection phenomenon caused by DMX signal in the
transmitting process. PIN 2 PIN 3
120Ω
1
3
2
·The connection between the light fixture and a DMX lighting console should use 5-pin XLR shielded cable and make sure its diameter is less than 0.3mm.
XLR plug/ socket and the wire should be connected as pictured above.
·Pin 1, Pin 2, Pin 3 for connecting DMX signals, Pin 4, Pin 5 are unassigned.
NOTE: When connecting with socket, make sure the internal pins are not in contact with the inner case. The fixture can match the DMX 512(1990) control signal.
·Adapting 5-pin and 3-pin XLR plug/socket conversion is a compatible option. The optional DMX cable comes as a 5-pin XLR plug. If you use the 3-pin XLR plug,
kindly follow below instruction.
Five Pin
Pin 1:GND(SCREEN)
Pin 2:Signal(-)
Pin 3:Signal(+)
Pin 4:N/C
Pin 5:N/C
Three Pin
Pin 1:GND(SCREEN)
Pin 2:Signal(-)
Pin 3:Signal(+)

6
000-255
0-51
Brightness Control
CCT
GEL
HSI
RGBW
EFFECT
1DIM
CCT
52-102
103-153
2
HSI
RGBW
GEL
Channel Detail DMX value Description
154-204
205-255
EFFECT
3
CCT
HSI
RGBW
GEL
EFFECT
CCT
HUE
RED Color Adjustment
3200K
5600K
000-255
000-255
000-255
000-127
128-255
CCT Adjustment 2700K-7500K
0-360
Filters color
4
Channel Detail DMX value Description
HUE-LOOP 000-017 RGB cycle
CCT-LOOP
FLASH
PULSE
STORM
POLICE CAR
TV
PAPARAZZI
CANDLE-FIRE
DISCO
018-034
035-051
052-068
069-085
086-102
103-119
120-136
137-153
154-170
CCT cycle
000-255
000-255
000-255
000-255
000-255
0-127
128-255
0-127
128-255
000-255
0-63
64-127
128-191
192-255
000-225
000-225
000-225
000-225
(-50)-(+50)
0%-100%
CCT
HSI
RGBW
GEL
EFFECT
HUE-LOOP
CCT-LOOP
FLASH
STORM
POLICE CAR
TV
PAPARAZZI
CANDLE-FIRE
DISCO
G/M
SAT
GREEN Color Adjustment
FILTER-NUM
HUE1
CCT1
CCT
HSI
CCT
HSI
CCT
B
RB
BW
RBW
CCT
CCT
ADD-RED
SAT
PULSE
000-255

7
000-127
5
CCT HARD
128-255
SOFT
RGBW BLUE Color Adjustment 000-255
6
EFFECT
HUE-LOOP
CCT-LOOP
FLASH
HUE2
CCT2
CCT
000-255
000-255
000-255
HUE 000-255
CCT
HSI
PULSE CCT 000-255
HUE 000-255
CCT
HSI
0-63
POLICE CAR
SINGLE
64-127
DOUBLE
128-191
TRIPLE
192-255
QUAD
TV G/M000-255
PAPARAZZI
CANDLE-FIRE
DISCO
SPEED
SAT
SPEED
000-255
000-255
000-255
STORM
TV
CANDLE-FIRE
DISCO
FLASH-TIMES-L
SPEED
SPEED
COLORS:3
COLORS:6
COLORS:9
COLORS:12
COLORS:15
COLORS:18
COLORS:21
COLORS:24
000-255
000-255
000-255
0-31
32-63
64-95
96-127
128-159
160-191
192-223
224-255
6
RGBW
SAT 000-255
HUE-LOOP
CCT-LOOP
FLASH
PULSE
SPEED
G/M
SAT
G/M
SAT
000-255
000-255
000-255
000-255
000-255
7
HUE-LOOP SPEED 000-255
CCT-LOOP
FLASH
PULSE
STORM
TV
CANDLE-FIRE
ONE-WAY
TWO-WAY
INTERVALS
PULSES/MIN
FLASH-TIMES-H
DIMMING-RANGE-L
DIMMING-RANGE-L
000-127
128-255
000-255
000-255
000-255
000-255
000-255
STORM RANDOM MODE 000-127
MANUAL MODE 128-255
Channel Detail DMX value Description Channel Detail DMX value Description
Channel Detail DMX value Description
000-255
WHITE Color Adjustment
EFFECT
EFFECT

8
8
HUE-LOOP ONE-WAY 000-127
CCT-LOOP
TWO-WAY
ADD-ON:OFF
ADD-ON:FLASH
ADD-ON:PULSE
128-255
000-085
086-170
171-255
FLASH RAIO 000-255
STORM
CANDLE-FIRE
9
FLASH-SPEED
FLICKERS:ON
FLICKERS:OFF
000-255
000-127
128-255
HUE-LOOP ADD-ON:FLASH
ADD-ON:OFF
086-170
000-085
CCT-
LOOP
FLASH
ADD-ON:PULSE
INTERVALS
PULSES/MIN
PAUSE:ON
171-255
000-255
000-255
000-127
ADD-ON:
FLASH
ADD-ON:
PULSE
STORM
PAUSE:OFF
INTERVAL-RANG-L
128-255
000-255
000-127
128-255
RANDOM
MANUAL
NO TRIGGER
TRIGGER
9
10
HUE-
LOOP
INTERVALS
PULSES/MIN
000-255
000-255
ADD-ON:
FLASH
ADD-ON:
PULSE
RATIO 000-255
INTERVAL-RANGE-H 000-255
CCT-
LOOP
STORM RANDOM
11
RATIO 000-255
STORM PAUSE:ON 000-127
PAUSE:OFF 128-255
RANDOM
12
LIGHTING
SILENT
NORMAL
000-085
086-170
HUE-
LOOP
ADD-
ON:FLASH
BOOST 171-255
Channel Detail DMX value Description Channel Detail DMX value Description
Mode 2： Total 7 channels, set the first fixture's DMX start address to 001, 008 for the second one displays, 015 for the third one and so on.
1
2G
R
0-255
0-255
B
W
Y
HARD
0-255
0-255
0-255
0-127
SOFT 128-255
6
5
4
3
7NORMAL
SILENT
86-170
0-85
BOOST 171-255
Channel Detail DMX value Description Channel Detail DMX value Description
EFFECT
EFFECT
EFFECT
EFFECT
ADD-ON:
FLASH

9
1.Wiring ( see sketch maps below)
①First, be sure that the power switch of the control unit is in the " off " position. Now it is safe to connect the adapter or battery and power unit on. If the power indicator is
on that means the power supply is normal. The LCD screen will display all the relevant information for the fixture will appear, from the remaining battery power and
address in lower right corner to the lighting mode in top left corner.
②CCT key: Press the CCT key to enter the operation interface of the CCT mode.
（1）Press the CCT key to switch between soft or hard light interface.
HSI RGBW GEL
PRESET MENU LOCK
HSI RGBW GEL
PRESET MENU LOCK
Soft light interface Hard light interface
（2）DIM setting: Rotate the dimmer knob, clockwise to increase the light's brightness while counterclockwise to reduce the light's brightness. Dim shows brightness
percentage on the display. ( As shown in figure 1 )
Note: For any mode( except the RGBW mode), when pressing the " dimmer knob " , the fixture will be off and the LCD display shows the percentage of DIM is 000%.
When pressing again, the fixture is returned to its previous status. Press the knob continuously to switch the fixture between off and on. ( As shown in figure 2 )
Operating Instructions
100% 2700K +45
DIM CCT G/M
CCT-SOFT
PRESS “CCT” TO CHANGE TO HARD LIGHT CH:512
NORMAL
000% 2700K +45
DIM CCT G/M
CCT-HARD
PRESS “CCT” TO CHANGE TO SOFT LIGHT CH:512
NORMAL
Clockwise rotation Counterclockwise
Figure 1 Figure 2
100% 2700K +45
DIM CCT G/M
000% 2700K +45
DIM CCT G/M
CCT-SOFT
PRESS “CCT” TO CHANGE TO HARD LIGHT CH:512
NORMAL CCT-SOFT
PRESS “CCT” TO CHANGE TO HARD LIGHT CH:512
NORMAL
Figure 1

10
（3）CCT setting: Rotate the " Function knob", clockwise to increase the color temperature while counterclockwise to reduce the color temperature. CCT shows the
values of color temperature on the display, the color temperature range is from 2700K-7500K. ( As shown in figure 3 )
Press the " Function knob" to adjust the color temperature in sequence, such as 2700K,3200K,4300K,5600K,6300K,7500K. If continuously to press, it will allow you
to adjust circularly. ( As shown in figure 4 )
Clockwise rotation Counterclockwise
（4）G/M setting: Rotate " SELECT knob ", clockwise to increase the G/M value while counterclockwise to reduce the G/M value. G/M shows the G/M values on the
display, the G/M range is from -50 to +50. Press the " SELECT knob" to reset its value to +00. (As shown in figure 5 ).
Figure 3 Figure 3 Figure 4
100% 7500K +45
DIM CCT G/M
100% 2700K +45
DIM CCT G/M
Clockwise rotation
100% 7500K +50
DIM CCT G/M
Figure 5
100% 7500K -50
DIM CCT G/M
Counterclockwise
Figure 5
000% 240 100%
DIM HUE SAT HSI RGBW GEL
PRESET MENU LOCK
③HSI Key: Press the HSI key to enter the operation interface of the HSI mode.
CCT-SOFT
PRESS “CCT” TO CHANGE TO HARD LIGHT CH:512
NORMAL CCT-SOFT
PRESS “CCT” TO CHANGE TO HARD LIGHT CH:512
NORMAL
CCT-SOFT
PRESS “CCT” TO CHANGE TO HARD LIGHT CH:512
NORMAL CCT-SOFT
PRESS “CCT” TO CHANGE TO HARD LIGHT CH:512
NORMAL
HSI
CH:512
NORMAL

11
（1）DIM setting: Rotate the " Dimmer knob" to adjust the brightness. ( As shown in figure 6)
000% 360 100%
DIM HUE SAT
（2）HUE setting: Rotate the " Function knob " to select HUE, the range of color adjusting range is 000-360, ( As shown in figure 7 ) Press the " Function knob" to adjust
the color in sequence, each time to press, the values will increase 60. When it gets to 360, it starts from 60 again.
( HUE: 000: Red, HUE:120 :Green, HUE:240:Blue, HUE:360:Red ). ( As shown in figure 8 )
000% 000 100%
DIM HUE SAT
Figure 7 Figure 7
100% 240 100%
DIM HUE SAT
000% 240 100%
DIM HUE SAT
Figure 6 Figure 6
Clockwise rotation Counterclockwise
Clockwise rotation Counterclockwise
Figure 8
000% 360 100%
DIM HUE SAT
000% 000 000%
DIM HUE SAT
Clockwise rotation Counterclockwise
Figure 9 Figure 9
HSI
CH:512
NORMAL HSI
CH:512
NORMAL
HSI
CH:512
NORMAL HSI
CH:512
NORMAL
HSI
CH:512
NORMAL HSI
CH:512
NORMAL
（3）SAT setting: Rotate “ SELECT knob” , clockwise to increase the color saturation while counterclockwise to reduce the color saturation. SAT shows the percentage of
the color saturation on the display, the color saturation range is from 000%- 100%. Press the "SELECT knob", saturation wil cycle in 100%-075%-050%-025%-000%.
( As shown in figure 9 )

12
④RGBW Key: Press the RGBW key to enter the operation interface of the RGBW mode.
000%
WHITE HSI RGBW GEL
PRESET MENU LOCK
000
R
000
G
000
B
000%
WHITE
000
R
000
G
000
B
100%
WHITE
000
R
000
G
000
B
000%
WHITE
255
R
000
G
000
B
Rotate the "SELECT knob"
to select R,G,B or WHITE
Rotate the "Function knob" to adjust
the ration of R, G,B,WHITE
Rotate the "Function knob" to adjust
the ration of R, G,B,WHITE
⑤GEL Key: Press the GEL key to enter the operation interface of the GEL mode.
HSI RGBW GEL
PRESET MENU LOCK
000%
DIM
5600K
CCT
RGBW
CH:512
NORMAL
RGBW
CH:512
NORMAL RGBW
CH:512
NORMAL RGBW
CH:512
NORMAL
GEL
CH:512
NORMAL
DOUBLE CTB
（1）Rotate the " SELECT knob" to select R, G, B or WHITE, then rotate the " Function knob" to adjust the ratio of R, G, B, WHITE values for mixing color. The range of
adjusting R, G, B is from 000-255, and the range of adjusting WHITE is from 000%-100%.

13
GEL
CH:512
NORMAL GEL
CH:512
NORMAL
100%
DIM
5600K
CCT
000%
DIM
5600K
CCT
100%
5600K
CCT
000%
3200K
CCT
Clockwise rotation Counterclockwise
Clockwise rotation Counterclockwise
100%
DIM
5600K
CCT
Rotate the " SELECT knob" to select the color filter
GEL
CH:512
NORMAL GEL
CH:512
NORMAL
GEL
CH:512
NORMAL
DOUBLE CTB DOUBLE CTB
DOUBLE CTB DOUBLE CTB
DIM DIM
DOUBLE CTB
（1）DIM setting: Rotate the " Dimmer knob" to adjust the brightness.
（2）CCT setting: Rotate or press the "Function knob" to select the range of color temperature from 3200K-5600K, CCT shows the current values of color temperature on
the LCD display.
（3）GEL setting: Rotate the " SELECT knob" to select the filter you need. Total 43 kinds gels.

14
⑥EFFECT key: Press the EFFECT key to enter the interface of special effect.
DIM: 000%
HSI RGBW GEL
PRESET MENU LOCK
HUE1: 000
SPEED: 12s
ADD-ON: FLASH
INTERVALS: 01.00s RATIO: 050%
HUE2: 360 SAT: 100%
MODE: ONE WAY
EFFECT:HUE LOOP
·MixPanel60/ MixPanel150 has total build-in 10 lighting modes, HUE LOOP/CCT LOOP/ FLASH/ PULSE/ STORM/ POLICE CAR/TV/ PAPARAZZI/ CANDLE/ FIRE/ DISCO.
DIM: 000%
HUE1: 000
SPEED: 12s
ADD-ON: FLASH
INTERVALS: 01.00s RATIO: 050%
HUE2: 360 SAT: 100%
MODE: ONE WAY
EFFECT:HUE LOOP DIM:000%
HUE1: 000
SPEED: 12s
ADD-ON: FLASH
INTERVALS: 01.00s RATIO: 050%
HUE2: 360 SAT: 100%
MODE: ONE WAY
EFFECT:HUE LOOP
HUE LOOP
CCT LOOP
FLASH
PULSE
STORM
POLICE CAR
TV
PAPARAZZI
CANDLE/FIRE
DISCO
（1）HUE LOOP
DIM: 000%
HUE1: 000
SPEED: 12s
ADD-ON: FLASH
INTERV ALS:01.00s RATIO:050%
HUE2:360 SAT:100%
EFFECT: HUE LOOP
MODE:ONE WAY
DIM: 000%
HUE1: 000
SPEED: 12s
ADD-ON: FLASH
INTERV ALS: 01.00s RATIO: 050%
HUE2: 360 SAT: 100%
EFFECT: HUE LOOP
MODE:ONE WAY ONE WAY
TWO WAY
Rotate "SELECT knob" to EFFECT. Rotate "Function knob" to select the special effect.
Rotate "SELECT knob" to MODE. Rotate "Function knob" to select the mode.
EFFECT
PRESS "SELECT" TO RESTART FROM HUE1 CH:512
NORMAL
EFFECT
PRESS "SELECT" TO RESTART FROM HUE1 CH:512
NORMAL EFFECT
PRESS "SELECT" TO RESTART FROM HUE1 CH:512
NORMAL
EFFECT
PRESS “SELECT” TO RESTART ART FROM HUE CH:512
NORMAL
EFFECT
PRESS “SELECT” TO RESTART ART FROM HUE CH:512
NORMAL
·HUE LOOP has total two cycle modes: ONE WAY and TWO WAY.

15
·HUE LOOP has total three ADD-ON ways: OFF, FLASH, PULSE.When the add-on is in the "off" position, the lighting effect will cycle only.
DIM: 000%
HUE1: 000
SPEED: 12s
INTERV ALS: 01.00s RATIO: 050%
HUE2: 360 SAT: 100%
EFFECT: HUE LOOP
MODE: ONE WAY
ADD-ON: FLASH
·Rotate "Dimmer knob" to adjust the brightness, rotate "SELECT knob" to select HUE1, HUE2, SAT, SPEED , MODE, ADD-ON, then rotate
"Function knob", to set up option and parameter according to demand.
FLASH(cycle and flash) add-on mode, INTERVALS is the flash interval period. Rotate "Function knob" to adjust flash interval period, adjustment range is 00.10S-10.00S.
Rotate "SELECT knob" to ADD-ON. Rotate "Function knob" to select the special effect.
DIM: 000%
HUE1: 000
SPEED: 12s
INTERV ALS: 01.00s RATIO: 050%
HUE2: 360 SAT: 100%
EFFECT: HUE LOOP
MODE: ONE WAY
ADD-ON: FLASH
Rotate "SELECT knob" to INTERVALS. Rotate "Function knob" to adjust flash interval period.
DIM: 000%
HUE1: 000
SPEED: 12s
RATIO: 050%
HUE2: 360 SAT: 100%
EFFECT: HUE LOOP
MODE: ONE WAY
ADD-ON:FLASH
INTERVALS: 01.00s
DIM: 000%
HUE1: 000
SPEED: 12s
RATIO:050%
HUE2: 360 SAT: 100%
EFFECT: HUE LOOP
MODE: ONE WAY
ADD-ON: FLASH
INTERVALS: 10.00s
00.10s
.
.
.
10.00s
·ADD-ON: In FLASH mode, rotate the "function knob" to
adjust the RATIO. The adjustment range is 000%-100%,
the higher percentage, the longer the flash duration,
100% means the lamp is always on. 50% represents the
time light is on and light off are the same. 000% represents
the lamp always lighting-off in one period.
(As shown in right picture)
EFFECT
PRESS “SELECT” TO RESTART ART FROM HUE CH:512
NORMAL EFFECT
PRESS “SELECT” TO RESTART ART FROM HUE CH:512
NORMAL
EFFECT
PRESS “SELECT” TO RESTART ART FROM HUE CH:512
NORMAL
EFFECT
PRESS “SELECT” TO RESTART ART FROM HUE CH:512
NORMAL
Rotate "Function knob" to adjust the ratio and the percentage of flash.
DIM: 000%
HUE1: 000
SPEED: 12s
HUE2: 360 SAT: 100%
EFFECT: HUE LOOP
MODE: ONE WAY
ADD-ON: FLASH
INTERVALS: 10.00s
EFFECT
PRESS “SELECT” TO RESTART ART FROM HUE CH:512
NORMAL
RATIO: 050%
000%
.
.
.
100%
OFF
FLASH
PULSE

16
·ADD-ON: PULSE/MIN is to adjust the times in one pulse cycle, the adjustment range is 1-240, 50 means there has 50 pulses in one cycle period.
（2）CCT LOOP
DIM: 000%
HUE1: 000
SPEED: 12s
HUE2: 360 SAT: 100%
EFFECT: HUE LOOP
MODE: ONE WAY
ADD-ON: PULSE
Rotate "SELECT knob" to PULSE/MIN. Rotate "Function knob" to adjust the times of pulse.
DIM: 000%
HUE1: 000
SPEED: 12s
PULSES/MIN: 50
HUE2: 360 SAT: 100%
EFFECT: HUE LOOP
MODE: ONE WAY
ADD-ON: PULSE 1
.
.
.
.
240
EFFECT
PRESS "SELECT" TO RESTART FROM CCT1 CH:512
NORMAL EFFECT
PRESS "SELECT" TO RESTART FROM CCT1 CH:512
NORMAL
PULSES/MIN: 50
（3）FLASH
DIM: 000%
CCT1: 2700K
SPEED: 02s
CCT2: 7500K
EFFECT
PRESS "SELECT" TO RESTART FROM CCT1 CH:512
NORMAL
MODE: ONE WAY
ADD-ON:FLASH
RATIO: 050%INTERV ALS: 10.00s
Rotate "SELECT knob" to adjust the selection
DIM: 000%
CCT1: 2700K
SPEED: 02s
CCT2: 7500K
EFFECT:CCT LOOP
EFFECT
PRESS "SELECT" TO RESTART FROM CCT1 CH:512
NORMAL
MODE: ONE WAY
ADD-ON: FLASH
RATIO: 050%INTERV ALS:10.00s
Rotate "Function knob" to set up options and parameter.
EFFECT: CCT LOOP
·CCT LOOP has total two modes: ONE WAY and TWO WAY.
CCT LOOP has total three ADD-ON ways: OFF(only cycle),FLASH(cycle and flash),PULSE(cycle and pulse).
·Rotate "Dimmer knob", to adjust the brightness, rotate "SELECT knob" to select CCT1, CCT2, SPEED MODE, ADD-ON, then rotate "Function knob", to set up options
and parameter according to demands.
·FLASH has total 2 modes: CCT, HSI.
·Rotate "Dimmer knob" to adjust the brightness, rotate "SELECT knob" to MODE, then rotate "Function knob", to select the flash mode CCT or
HSI according to demands.
·CCT mode, rotate "SELECT knob" to select CCT, G/M, INTERVALS, FLASH RATIO, PAUSE, then rotate "Function knob", to set up options and
parameter according to demands.
PAUSE: to select ON or OFF according to demands.

17
·HSI mode, rotate "SELECT knob" to select HUE, SAT, INTERVALS, FLASH RATIO, PAUSE, then rotate "Function knob", to set up options and parameter according
to demands.
Rotate "Function knob" to set up options and parameter.
DIM: 000%
INTERVALS: 01.09s
FLASH RATIO: 098%
EFFECT: FLASH
EFFECT
CH:512
NORMAL
PAUSE: ON
CCT:: 2700K G/M: +00MODE:CCT
Rotate "SELECT knob" to adjust selection.
DIM: 000%
INTERVALS: 01.09s
FLASH RATIO: 098%
EFFECT: FLASH
EFFECT
CH:512
NORMAL
PAUSE: ON
MODE:HSI HUE: 120 SAT: 100%
（4）PULSE
Rotate "SELECT knob" to adjust selection.
DIM: 000%
PULSES/MIN: 5
EFFECT: PULSE
EFFECT
CH:512
NORMAL
HUE: 120 SAT: 100%MODE:HSI
Rotate "Function knob" to set up options and parameter.
DIM: 000%
PULSES/MIN: 5
EFFECT: PULSE
EFFECT
CH:512
NORMAL
CCT: 7500K G/M: +50MODE:CCT
·PULSE has total two modes: CCT and HSI.
·Rotate "Dimmer knob" to adjust the brightness rotate "SELECT knob" to MODE, to select CCT and HSI.
·CCT mode, rotate "SELECT knob" to select CCT, G/M, PULSES/MIN, then rotate "Function knob", to set up options and parameter according to demands.
·HSI mode, rotate "SELECT knob" to select HUE, SAT, PULSES/MIN, then rotate "Function knob", to set up options and parameter according to demands.

18
Rotate "SELECT knob" to adjust selection. Rotate "Function knob" to set up the options and parameter.
DIM: 000%
INTERVAL RANGE: 15s-20s
EFFECT:STORM
EFFECT
CH:512
NORMAL
CCT: 6000K
FLASH TIMES: 04-05
MODE: RANDOM
FLASH SPEED: 005 PAUSE: OFF
DIM: 000%
INTERVAL RANGE: 15s-20s
EFFECT:STORM
EFFECT
CH:512
NORMAL
FLASH TIMES: 04-05
MODE: RANDOM
FLASH SPEED: 005 PAUSE: 005
CCT: 6000K
Rotate "Function knob" to select the lighting colors.
DIM: 000%
MODE: TRIPLE
EFFECT
CH:512
NORMAL
EFFECT: POLICE CAR BLUE
RED&BLUE
BLUE&WHITE
RED&BLUE&WHITE
COLOR: RED&BLUE&WHITE
Rotate "Function knob", to select the MODE.
DIM: 000%
EFFECT
CH:512
NORMAL
EFFECT: POLICE CAR
COLOR: RED&BLUE&WHITE
MODE: TRIPLE
（5）STORM
·STORM offers two modes: RANDOM and MANUAL.
·Rotate "Dimmer knob", to adjust the brightness, rotate "SELECT knob" to select RANDOM or MANUAL, then rotate the "function knob" to select the RANDOM
or MANUAL mode.
·RANDOM mode, rotate "SELECT knob" to select CCT, INTERVAL RANGE, FLASH TIMES, FLASH SPEED, PAUSE, then rotate "Function knob", to set up the options
and parameter according to demands.
·MANUAL mode, rotate "SELECT knob" to select the CCT, FLASH TIMES, FLASH SPEED, then rotate "Function knob", to set up the options and parameter
according to demands. After set up, press the "SELECT knob" to trigger the storm mode.
（6）POLICE CAR
·Set up POLICE CAR mode, rotate "Dimmer knob", to adjust the brightness, rotate "SELECT knob" to COLOR, then rotate "Function knob", to select the color,
rotate "SELECT knob" to MODE, then rotate "Function knob", to select the MODE for the police car lighting effect.（SINGLE/DOUBLE/TRIPLE/QUAD）.

19
Rotate "SELECT knob" to adjust the selection.
DIM: 000%
CCT: 6600K
SPEED: 001
EFFECT
CH:512
NORMAL
EFFECT: PAPARAZZI
Rotate "Function knob" to set up the options and parameter.
DIM: 000%
CCT: 6600K
EFFECT
CH:512
NORMAL
EFFECT: PAPARAZZI
SPEED: 005
Rotate "SELECT knob" to adjust the selection. Rotate "Function" to set up the options and parameter.
DIM: 000%
CCT: 6200K
SPEED: 001
EFFECT
CH:512
NORMAL
EFFECT: TV
DIMMING RANGE: 000%-000%
G/M: +50
DIM: 50%
CCT: 6200K
SPEED: 001
EFFECT
CH:512
NORMAL
EFFECT: TV
G/M: +50
DIMMING RANGE: 40%-50%
（7）TV
·Rotate "Dimmer knob", to adjust the brightness, rotate "SELECT knob" to select CCT, G/M, SPEED(TV flash speed, range is 001-100), DIMMING RANGE(brightness
range, 000%-90%…000%-100%, 000%-100% same as Dimmer brightness percentage), then rotate "Function knob", to set up the options and parameter according
to demands.
（8）PAPARAZZI
·Rotate "Dimmer knob", to adjust the brightness, rotate "SELECT knob" to select CCT, SPEED(camera shooting flash speed, range is 001-100), then rotate "Function
knob", to set up the options and parameter according to demands.