NANLITE Forza 720B User manual

Guangdong NanGuang Photo&Video Systems Co., Ltd
USER MANUAL
Forza 720B

1
Technical Data
Rated power: 800W
Input voltage/current: DC48V/16.67A Max
AC100-240V 50/60Hz
Color Temperature: 2700K-6500K
CRI: average 96
TLCI: average 97
Product Diagram
Forza 720B LED Bi-color Spot Light

2
Product Details
7. Lock Catch
6. Yoke
4. Reflector
3. Umbrella Hole
2. Fixture Body
Input Socket
1. Fixture Body Handle
5. Adjustable Handle

3
10. AC Power Input Socket
11. Power Switch
12. DMX IN
8. Control Unit
Output Socket
9. DMX OUT
16. Control Unit
Handle
15. Battery Holder
13. USB Port
15. Battery Holder
17. Quick Release
Plate
14. Control Panel

4
Detailed Description
1. Fixture body handle: Be convenient for users to lift the lamp head and adjust the diection of the light.
2. Fixture body input socket: For connecting the lamp head with control unit.
3. Umbrella hole: For installing/removing an umbrella.
4. Reflector: For concentrating light to improve the central illumination.
5. Adjustable Handle: Tighten or release the tilt movement of the fixture on the yoke.
6. Yoke: Mount the fixture on a stand, pan and tilt.
7. Lock catch: To lock or release the reflector or other accessories.
8. Control unit output socket: To connect a DC cable for connecting between the lamp head and control unit.
9. DMX OUT: DMX signal output interface.
10. AC power input socket: For connecting the AC power cable to supply power to the control unit.
11. Power switch: To turn on/off the fixture.
12. DMX IN: DMX signal input interface.
13. USB port: For updating the firmware
14. Control panel: For displaying various function operations and data.
15. Battery holder: For mounting the 14.8V/12A V-mount battery.
16. Control unit handle: Be convenient for users to lift the control unit.
17. Quick release plate: For mounting the quick release clamp.

5
Usage
1. Connection Between the Light Fixture, Control Unit and the Power Outlet.

6
Note:
①When connecting the power supply, please make sure the power, voltage and frequency are consistent with the
control unit.
②Make sure to use the provided power cable and DC connecting cable. The connection between the DC plug and
the fixture body input socket should be connected as following.
1: Power supply + pole
2: Power supply - pole
3: D+
4: NC
5: D-
6: GND
7: NC
8: NC
5 3
6
2 1
7
4
8
3 5
8
1 2
7
4
6
5D-
NC
NC
2-
6GND
3D+
1+
NC
5D-
NC
NC
2-
6GND
3D+
1+
NC

7
2. Connection Between the Light Fixture and Control Unit with Battery
Note:
1. When powered by two 14.8V batteries, the maximum output is 40%.
2. When powered by two 26V batteries, the maximum output is 65%.
3. Do not use the 14.8V and 26V batteries at the same time, or use only one battery of either kind to
power the fixture.
4. The batteries are not included and are sold separately.
Battery

8
3. Quick Release Clamp Installation
1. Loosen the adjustable handle to open the clamp. 2. Mount the quick release clamp on the light
stand, then rotate the adjustable handle to
tighten the clamp.
3. Align the quick release plate on the control unit
with the quick release mount on the clamp to
mount the control unit on to the clamp.
4. When removing the control unit, press the lock
catch on the clamp and release the control unit
from the clamp.

9
4. Reflector Installation
1. Align the reflector with the mount and rotate
according to the lock catch sign to secure it
into the fixture.
2. Press the lock catch and rotate the reflector
according to the sign to release it from the fixture.

10
·Forza 720B supports 2.4G remote control, DMX/RDM control, and includes a built-in bluetooth module as well.
▲Address code need to be pre-set for 2.4G remote control, DMX/RDM control solutions.
Remote Control
①Address Setting
Press MENU button to access options.
1. ADDRESS/DMX, including ADDRESS, DMX MODE and DMX DIMMING CURVE settings.
CCT EFFECT MENU LOCK
MENU
OUTPUT MODE
ADDRESS/DMX
RESET BLUETOOTH
WIRELESS PROTOCOL
FAN CONTROL
ROTATE SCREEN
ON
CH: 512
Left knob Right knob

11
Rotate ''Right knob'' to ADDRESS/DMX. Press ''Right knob'' to enter the corresponding sencondary menu.
Rotate ''Right knob'' to ADDRESS. Press ''Right knob'' to enter the corresponding third menu.
Rotate ''Right knob'' to select the desired ADDRESS code. Press ''Right knob'' to set.
MENU
OUTPUT MODE
ADDRESS/DMX
RESET BLUETOOTH
WIRELESS PROTOCOL
FAN CONTROL
ROTATE SCREEN
ON
CH: 512 MENU
ADDRESS
DMX MODE
DMX DIMMING CURVE
CH: 512
ON
PRESS “MENU” TO RETURN
MENU
ADDRESS
DMX MODE
DMX DIMMING CURVE
CH: 512
PRESS “MENU” TO RETURN
ON
PRESS “MENU” TO RETURN
MENU
512
ADDRESS
ON
PRESS “MENU” TO RETURN
MENU
512
ADDRESS
ON
PRESS “MENU” TO RETURN
MENU
SET
ON
PRESS “MENU” TO RETURN

12
2. DMX MODE
Rotate ''Right knob'' to DMX MODE. Press ''Right knob'' to enter the corresponding third menu.
Rotate ''Right knob'' to select the corresponding DMX mode. Press ''Right knob'' to set.
MENU
ADDRESS
DMX MODE
DMX DIMMING CURVE
CH: 512
ON
PRESS “MENU” TO RETURN
MENU
CCT 8bit
CH: 512
CCT 16bit
ULTIMATE DMX 8bit
ON
PRESS “MENU” TO RETURN
MENU
CCT 8bit
CH: 512
CCT 16bit
ULTIMATE DMX 8bit
ON
PRESS “MENU” TO RETURN
MENU
SET
CH: 512
ON
PRESS “MENU” TO RETURN

13
Rotate "Right knob'' to DMX DIMMING CURVE. Press ''Right knob'' to enter the corresponding third menu.
Rotate ''Right knob'' to select the corresponding DMX dimming curve. Press ''Right knob'' to set.
3. DMX DIMMING CURVE
MENU
ADDRESS
DMX MODE
DMX DIMMING CURVE
CH: 512
ON
PRESS “MENU” TO RETURN
MENU
LINEAR
EXPONET
LOGARITHM
S CURVE
CH: 512
ON
PRESS “MENU” TO RETURN
MENU
LINEAR
EXPONET
LOGARITHM
S CURVE
CH: 512
ON
PRESS “MENU” TO RETURN
MENU
SET
CH: 512
ON
PRESS “MENU” TO RETURN

14
2. DMX Remote Control
①Connect the fixture to the DMX/RDM consoles via DMX cable as shown below:
DMX IN DMX OUT
1 GND
2 DATA-
3 DATA+
NC
NC
NC
NC
GND 1
DATA- 2
DATA+ 3
·The connection between light fixtures, or light fixture and DMX/RDM console, must use five core shielded cable.
Make sure its diameter is not less than 0.3mm. XLR plug/socket and the wire should be connected as shown
above.
·Pin1, Pin2, Pin3 for connecting DMX signal. Pin4, Pin5 has no connection.
▲NOTE: When connecting DMX, make sure the internal pin is not in contact with the inner case. The fixture can
match the DMX512 (1990) control signal.
·Plug of 5-Pin and 3-Pin XLR plug/socket conversion. The fixture is supplied with 5-Pin XLR plug. lf using a 3-Pin
XLR plug, please follow the instructions below.
5PIN
Pin 1:GND(SCREEN)
Pin 2:Signal(-)
Pin 3:Signal(+)
Pin 4:N/C
Pin 5:N/C
3PIN
Pin 1:GND(SCREEN)
Pin 2:Signal(-)
Pin 3:Signal(+)

15
②DMX Terminator
ln DMX control mode, the DMX output of the last light fixture should be connected with a DMX terminator
(not included). The terminator is connected with a 120Ω(OHM) resistor across Pin 2 and Pin 3 (As shown below).
This prevents interference caused by DMX signals in the transmitting process.
DMX Terminator Connection
Connect a 120Ω(OHM) resistor
across Pin 2 and Pin 3 in an XLR
plug and insert into the DMX OUT
socket on the last unit.
PIN 2 PIN 3
120Ω
1
2
3
5
4
③Address Setting of the Light Fixtutre.
④Refer to the DMX reference guide and control the light via DMX/RDM console.
(For detailed operation please refer to the DMX/RDM console operation manual.)
Note: DMX reference guide "Forza_720B_DMX_REFERENCE_GUIDE_EN" is downloadable from
www.nanlite.com.

16
3. 2.4G Remote Control
·Set the address of the 2.4G remote controller to be consistent with the light fixture, enabling the fixture to be
remotely controlled by 2.4G remote controller or by APP via the transmitter box.
Note: ①2.4G remote controller and transmitter box are sold separately.
②The fixture supports the 2.4G wireless protocol V1.0 and V2.0. Please set fixture to V2.0 while using
WS-RC-C1 or WS-RC-C2 remote controller. Please set fixture to V1.0 while using other remote controllers.
Rotate ''Right knob'' to WIRELESS PROTOCOL, press ''Right knob'' to enter the corresponding sencondary menu.
Rotate ''Right knob'' to select V1.0 or V2.0, press ''Right knob'' to set.
MENU
OUTPUT MODE
ADDRESS/DMX
RESET BLUETOOTH
WIRELESS PROTOCOL
FAN CONTROL
ROTATE SCREEN
ON
CH: 512 MENU
V1.0 V2.0
2.4G WIRELESS PROTOCOL
CH: 512
ON
PRESS “MENU” TO RETURN
MENU
V1.0 V2.0
2.4G WIRELESS PROTOCOL
CH: 512
ON
PRESS “MENU” TO RETURN
MENU
SET
CH: 512
ON
PRESS “MENU” TO RETURN

17
0008 XXXX XXXX
Serial number
Manufacturer: Nanguang
0202：Forza 720B
1. Be sure that the power switch of the control unit is in the "off ". Now it is safe to connect the control unit and power
the unit on, the screen will display "NANLITE".
Operating Instructions
4. RDM Remote Control
①Connect the light fixture to the console with RDM function by using a connection cable, the connection method is
the same as that with a DMX/RDM console.
②Control the fixture via a console with RDM function. (For specific operation methods, please refer to the RDM
console operation manual.)
Note: The UID format of the fixture is as follows:
ON
CH: 512
CCT MODE
5600K
CCT
100.0%
DIM
Powered by
power supply
Address
Brightness CCT
Mode
Unlock/lock state
Fan status

18
ON
CH: 512
CCT MODE
2700K
CCT
0.0%
DIM
ON
CH: 512
CCT MODE
2700K
CCT
100.0%
DIM
2.CCT button: press the CCT button to enter the CCT mode.
CCT EFFECT MENU LOCK
①Brightness setting, rotate "Left knob" clockwise to increase the brightness while counterclockwise to reduce
the brightness, the screen will show the percentage of brightness, DIM range: 0.0-100.0%.
Note: In other modes, the range of brightness adjustment is the same as that in CCT mode. When the fixture
function is unlocked, in any mode, press the "Left knob" to turn off the light, the brightness percentage
indicated on the screen is 0.0% in this case. Press again to restore the light to its previous state, and
press continuously to switch between on and off.
0.0%
.
.
.
100.0%
ON
CH: 512
CCT MODE
5600K
CCT
100.0%
DIM

19
ON
CH: 512
CCT MODE
2700K
CCT
100.0%
DIM
ON
CH: 512
CCT MODE
6500K
CCT
100.0%
DIM
3. EFFECT Button: Press the EFFECT button to enter EFFECT MODE.
Left knob Right knob
CCT EFFECT MENU LOCK
②CCT setting, rotate "Right knob" clockwise to increase the CCT while counterclockwise to reduce the CCT,
the CCT is shown on the screen, CCT range: 2700K-6500K.
Note: Press the "Right knob" could quickly switch to 2700K, 3200K, 4300K, 5600K, 6500K.
2700K
.
.
.
6500K
ON
DIM: 100.0%
CCT: 2700K - 6500K
SPEED: 8s
EFFECT MODE CH: 512
EFFECT: CCT LOOP