NANOLUX SUPER DE 1000W User manual

MAINTENANCE
WARRANTY
Nanolux Technology warrants the mechanical and electronic components of
this product to be free of defects in material and workmanship if used under
normal operating conditions for a period of three (3) years from the original
date of purchase. If the product shows any defects within this period and that
defect is not due to user error or improper use, Nanolux Technology shall, at
its discretion, either replace or repair the product using suitably new or
refurbished parts. For Nanolux DE HPS lamps and reflector the warranty period
is one (1) year from the original date of purchase. In case Nanolux decides to
replace the entire product, this limited warranty shall apply to the
replacement ballast for the remaining initial warranty period, i.e. three (3)
years from the date of purchase of the original product. For service return the
ballast to your shop with the original sales receipt.
For more information about Nanolux product please visit nanoluxtech.com
FIXTURE HANGING
Fixture hanging equipment included with unit for necessary mounting.
1. Attach the ring bolt to the reflector support frame (a).
2. Attach the carbineers on the steel wire hanger to ballast hanging holes (b).
3. Hang the fixture in the desired locations (c).
There are no serviceable parts inside the luminaire. Opening the luminaire
will void warranty. Keep housing clean from dust and dirt with a dry or damp
cloth to ensure optimal cooling. When using a damp cloth disconnect from
the power first. Check your electrical connections regularly. OPERATING
MANUAL
BALLAST
SUPER DE 1000W
DOUBLE ENDED FIXTURE
NCCS-0-10V
Illuminating Your Grow
www . n a n oluxtech.com

BEFORE INSTALLATION, PLEASE READ
THESE INSTRUCTIONS FIRST.
TECHNICAL SPECIFICATIONS
CAUTION:
LAMP REPLACEMENT AND HOT
RESTRIKE
1000W
AC480V
200V-300V
50/60Hz
MAX 1100W
≥0.97
≤1.7
≤10%
590*240*242 mm
23.2*9.4*9.5 inch
Double Ended Lamp
Over Temperature Protection; Under Voltage Protection;
Open/Short Circuit Protection;
5.2 kgs
11.5 lbs
Size
(L*W*H)
Model
Weight
Protection
Function
Dimming
Strike Lamp
100KHz-200KHz
Output Frequency
Input Voltage
Output Voltage
Input Frequency
Output Power
Power Factor
Crest Factor
THD
Congratulations on the purchase of your new Nanolux DE FIXTURE 1000W
luminaire. We have done everything to ensure a long life and safe operation
of your new product, but the installation and use of the ballast is at the
responsibility of the user. Incorrect use or installation can lead to failure and
damage to the ballast. Damage to the luminaire and electronic circuitry as a
result of incorrect installation or use revokes your warranty. Read this manual
carefully before installing your luminaire.
This model is compatible with NCCS-0-10V protocol control.
Insert telephone wire into the jack of the NCCS-0-10V protocol control, and
then Dimming function on the luminaire will be enabled.
● Maximum of 120 ballasts can be controlled.
● Simulate sunrise and sunset for dimming.
● Turn off the device automatically with time and temperature setting.
In & Out jacks included on the ballast allows for multifixtures connected in
parallel.
NCCS-0-10V DIMMING
CAUTION:
After installation, verify installation was a success by cycling the lights on/off
a few times, by setting 'over temperature shut down' to a low value like 85°F,
and rubbing the temperature probe with your fingers, tricking the
NCCS-0-10V protocol control into an over temperature condition and
shutting the lights off. Then leave the probe alone, and after recommended
10-15 minutes NCCS-0-10V protocol control should turn all the lights back
on.
For detailed instructions, please refer to NCCS-0-10V protocol control
operating manual.
INSTALLATION
COMPLY WITH LOCAL INSTALLATION REGULATIONS
These luminaires are suitable for damp indoor locations. Do not install your
luminaires in a wet environment or outdoors.
Do not operate these luminaires close to combustible materials. The lamp
and reflector will get hot during operation. Do not touch the reflector or
lamp during or right after operation. Make sure the power cord does not
touch any hot part of the luminaire. Make sure the lamp is clean and inserted
correctly.
A normal operating environment temperature should be below 35°C (95°F).
Exceeding the maximum environmental temperature will stress electronic
components, which will lead to shorter lifetime and decreased reliability.
TO TAKE OUT A LAMP:
• DISCONNECT THE MAINS FIRST
• Open the lamp holders by sliding them outward. The lamp is held by a
metal spring at each side. It is recommended to hold the lamp while
opening the lamp holders to prevent the lamp from falling.
TO INSTALL A NEW LAMP:
• DISCONNECT FROM MAINS FIRST
• Make sure the lamp is clean, wear cotton gloves and clean the lamp after
installation with a dry soft cloth. Never use detergents to clean a lamp, use
pure alcohol or wipe clean with a dry clean soft cloth.
• Make sure the end wires are straight.
• Open the lamp holders by sliding them outward. Press the lamp in the
fitting until the metal springs hold the lamp, with the glass vacuum seal
pointed downward.
• Close the lamp holders by sliding them inward.
• Wipe the lamp with a clean soft cloth.
• Be sure not to touch the reflective material of the reflector with your bare
hands.
• Always install the lamp before connecting your luminaire to mains.
• Allow lamp to cool 30 minutes before restarting (hot restrike).
• When changing the lamp always disconnect the luminaire from mains by
removing the mains plug. Let the lamp and reflector cool down for 30
minutes before changing as they are very hot. When replacing a defect
lamp without disconnecting mains the lamp will not start. Disconnecting
the power will restart the ballast.
• DO NOT touch hot Ceramic socket.
• Make sure the DE lamp wires are correctly within the sockets copper wire
clamps.
• Make sure to fully close the ceramic socket to the correct position and keep
the socket clean to provide proper function.
• Fragile !! Be careful and do not exert excessive force while moving the
ceramic slider on the ceramic socket connection.
• Keep away from water.
NCCS-0-10V
REFLECTOR REPLACEMENT
The Nanolux Double Ended 1000W luminaires are designed and tested to
drive HPS & MH Electronic lamps. Using Single Ended 1000W HPS & MH
Electronic lamps can cause damage to your ballast and lamp.
SUITABLE LAMPS
The Nanolux DE fixture should be handled with care. If it is damaged or
deformed you should replace it. We recommend to change the reflector
every year for optimal results. Replacement reflectors are available through
your Nanolux Technology reseller.
To replace the reflector, you must remove the lamp first as described above
in how to install the lamp. Let the reflector cool down if it has been operating
to prevent an injury. At the end of the reflector bracket, you will find a
chrome knob. Pull the knob outward to release the pin holding the reflector
in place (a-1). The reflector can then be pulled away from the ballast end of
the bracket to remove it from the two pins holding it in place (a-2 & a-3).
When inserting the new reflector, slide it into the two pins (a-2 & a-3) and
then release the pin (a-1) to secure it in place.
NOTICE: Reflectors are made from a high grade pure aluminum, which will
oxidize and degrade over time. This results in lower reflectivity and reduced
efficiency, and over 10% light loss at the canopy. It is recommended that you
mark the installation date on the outside of reflector with a permanent
marker, and replace reflectors once a year.