Nautilus Glute Drive User manual

OWNER’S
MANUAL
CORE HEALTH & FITNESS
Glute Drive

Page 1
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS................................................................................................................2
IMPORTANT LABEL LOCATIONS ........................................................................................................................4
PRODUCT SPECIFICATIONS ........................................................................................................................6
OPERATIONS ........................................................................................................................7
ASSEMBLY ........................................................................................................................8
MAINTENANCE ......................................................................................................................11
TOOLS ................................................................. 11
MAINTENANCE SCHEDULE ................................................................. 12
SUPPORT & SERVICE ......................................................................................................................13

Page 2
Before using this product, it is essential to read the ENTIRE Owner’s Manual and ALL
installation instructions. The Owner’s Manual describes equipment setup and instructs
members on how to use correctly and safely.
Read all warnings posted on the machine.
Health related injuries may result from incorrect or excessive use of exercise equipment.
Core Health & Fitness strongly recommends you to encourage your members to discuss their
health program or fitness regimen with a health care professional, especially if you or they
have not exercised for several years, are over 35, or have known health conditions.
WARNING!
IMPORTANT SAFETY INSTRUCTIONS
WARNING - to reduce the risk of injury to
person:
24 in (0.6 m)
36 in (0.91 m)
Fig. 1 Required Clearance
1. Assemble and operate the machine on a solid
level surface. Position the machine with a
minimum of 24 inches (0.6 meters) of clearance
on each side to allow for ease of mounting and
dismounting. Allow for 48 inches (1.25 meters) of
clearance behind the machine. Leave a minimum
of 19.7 inches (0.5 meters) between two adjacent
units. These dimensions are the recommended
minimum distances.
The actual area for access and passage shall be
the responsibility of the facility and should take
into account this training envelope, Americans
with Disabilities Act Accessibility Guidelines
(ADAAG) requirements and any required local
codes or regulations (www.access-board.gov/
ada).
2. Do not exceed the maximum allowable weight
limit of:
• 350 lbs. (160 kg.)
3. All equipment MUST be secured (bolted and
tightened) to a solid, level surface, using all of
the anchoring holes provided, to stabilize and
eliminate rocking or tipping over. Shim any
mounting surface that does not rest thoroughly
on the floor using flat washers, DO NOT force the
foot to contact the ground with anchors.
Fasteners must have a minimum of 500 lbs.
tensile capacity, be a bolt of grade 2 or better
and be installed per the bolt manufacturer’s
specifications.
WARNING: Due to the wide variety of flooring
on which equipment may be anchored or installed
and differences in applicable local building codes,
Core Health & Fitness is not responsible for any
damage to the flooring that may result due to
anchoring or installing equipment to the floor and
for compliance with local building codes. Only
licensed contractors or certified installers should
be used to insure proper anchoring, installation,
and compliance with local building code.
4. This equipment is designed for use in a
commercial gymnasium or health club. To ensure
the proper use of the equipment in a safe manner,
all users of the equipment should read this
manual before using the machine. This machine
should be made a part of your club training
program in order that the equipment is used by

Page 3
your members in a safe manner as intended. In
addition to instructing the club members in the
proper use of the equipment, the club member
should obtain a complete physical examination
form their health care provider before beginning
any exercise program.
5. This machine is not intended to be used by
persons with reduced physical, sensory, or
mental capabilities or lack of experience and
knowledge, unless given instruction and under
the personal supervision concerning use of the
machine by a person responsible for their safety.
6. Keep children away.
7. The safety and integrity of this machine can only
be maintained when the equipment is regularly
examined for damage and wear and repaired.
It is the sole responsibility of the owner of this
equipment to ensure that regular maintenance
is performed. Worn or damaged parts must be
replaced immediately or the equipment removed
from service until the repair is made.
8. Do not over exert yourself during exercise. Stop
exercising if you feel pain or tightness in your
chest, become short of breath or feel faint. If you
feel pain or experience any abnormal symptoms,
stop exercising and consult your health care
provider.
9. Ensure all adjustment and locking features are
properly secured before using the equipment.
10. Use only replacement components supplied by
Nautilus®. Substitutes are forbidden and will void
all warranties.
11. Wear proper exercise clothing and athletic shoes
during a workout. Avoid wearing loose clothing.
Tie back long hair and keep towels away from
the moving parts. Face forward at all times and
never attempt to turn around while the machine is
moving.
12. Never use dumbbells or other means to
incrementally increase the weight resistance. Use
only those means provided by Nautilus.
13. When adjusting any seat, knee stabilization pad,
range of motion limiter, foothold pad or any other
type of adjuster, make certain that the adjusting
pin is fully engaged in the hole to avoid injury.
14. It is the purchaser’s sole responsibility to properly
instruct its end users and supervising personnel
as to the proper operating procedures of all
Nautilus equipment.
SAVE THESE INSTRUCTIONS

Page 4
This page shows examples of the warning labels and communication stickers placed on the equipment as part of the manufacturing process. It is critical that
owners maintain the integrity and placement of these stickers. If you find any stickers missing or damaged the replacement numbers are shown on the support site.
See Support and Service to order replacements. NOTE: STICKERS AND LABELS ARE NOT SHOWN TO SCALE
731-0512
Serial Label
050-5595
050-5594
050-5593
731-7920
731-0517
731-7311
050-5585
IMPORTANT LABEL LOCATIONS
Fig. 2
Core Health & Fitness, LLC
4400 NE 77th Avenue, Suite 300
Vancouver, WA 98662 USA
1-888-678-2476
P/N: 050-5457 Rev B
SKU
Serial
Color
Config.
Class S Fitness Equipment. Max User Weight 350 Lbs (160 Kg).
DESIGNED IN THE USA
MADE IN CHINA
Patents:
www.corehealthandfitness.com/patents

Page 5
PN:731-7920
support.nautilusstrength.com
1-800-503-1221
050-5595
STICKER,NAUTILUS,220X79
731-0512
STICKER,CAUTION,PINCH
731-0517
STICKER, WARNING,
BOLT DOWN
731-7920
STICKER,WARNING,NP STANDARD
INSTRUCTIONS
READ THE OWNERS MANUAL
AND FOLLOW ALL INSTRUCTIONS
PRIOR TO USING THE EQUIPMENT.
IMPROPER USE CAN RESULT IN SERIOUS
INJURY. EQUIPMENT SHOULD ONLY BE
USED IN A SUPERVISED ENVIORNOMENT.
AS WITH ALL EXERCISE EQUIPMENT OR
PROGRAMS, CONSULT A PHYSICIAN PRIOR
TO USE AND STOP IF YOU FEEL FAINT,
DIZZY OR EXHAUSTED.
INSPECT THE MACHINE PRIOR TO USE. DO
NOT USE EQUIPMENT IF SEATBELT IS CUT
OR HAS ABRASIONS THROUGH THE BELT
OR THE BELT CLASP DOES NOT FASTEN.
IMMEDIATELY REPORT WORN, LOOSE OR
DAMAGED EQUIPMENT TO MANAGEMENT
AND DO NOT USE EQUIPMENT UNTIL
REPAIRED.
ENSURE ALL ADJUSTMENT AND LOCKING
FEATURES ARE PROPERLY SECURED
BEFORE USING EQUIPMENT.
UTILIZE A BAR COLLAR TO SECURE WEIGHT
PLATES.
REPLACE LABEL IF DAMAGED, ILLEGIBLE
OR REMOVED.
050-5593
050-5594
BADGE,NAME,GLUTE DRIVE
731-7311
STICKER,NAUTILUS,
DECO,45MMX191MM
050-5593
STICKER,WARNING, GLUTE
DRIVE
050-5585
PLACARD,GLUTE DRIVE

Page 6
Fig. 3
PRODUCT SPECIFICATIONS
NP-L1131 Glute Drive
Unit Weight Width Length Height Max User Weight Max Load Weight
202 lbs
92 kg
60 in
152 cm
62 in
157 cm
35 in
89 cm
350 lbs
160 kg
360 lbs
163 kg

Page 7
OPERATIONS

Page 8
Required Tools:
• Metric Allen Key Set
• Metric Open-Ended Wrench
Set
• Large Adjustable Crescent
Wrench
• Loctite Blue1
Anchor Guidance:
• All equipment must be bolted down prior to use by a licensed contractor.
• WARNING: Equipment that Is not securely bolted to the floor is not safe.
• The customer is responsible for determining the suitability of the installations site.
• Factors such as equipment weight, vibration, overhead clearance, workout activities should be
considered.
• When the floor is constructed of concrete, the concrete should have a rated strength of at least
4000psi.
• The anchors should be installed in accordance with the manufacturers recommendations.
• It is the responsibility of the gym owner to ensure that the sub-floor and installation anchors are
appropriate for the equipment.
THREAD LOCKER APPLICATION: Clean all threads and holes, apply no more than 3-4 drops per bolt.
Thru Holes Blind Holes
PACKAGING REMOVAL:
Carefully remove all packaging materials that wrap the equipment. DO NOT USE A KNIFE OR BOX
CUTTER AS YOU MAY DAMAGE THE EQUIPMENT. At this time remove any sub-components from
the pallet and set aside for later assembly.
Once all packaging has been removed, lay all parts out in a clean open area to prepare for assembly.
Should any component not be present or if you have any operational questions, please refer to SUPPORT &
SERVICE
1 Unless otherwise noted Loctite 242/243 or equivalent thread locker must be used on all threaded fasteners. (Do not use thread locker when a Nyloc nut
is used.)
ASSEMBLY
Metric Steel Bolts Torque Specifications
Bolt Size Thread Pitch Torque, N-m (lbs-ft)
6mm 1.25 10 to13.5 (8 to10)
8mm 1.25 25.5 to 28.5 (19 to 21)
10mm 1.75 55.5 to 58 (41 to 43)
12mm 1.25 61 to 65 (45 to 48)
• Torque all hardware to values as specified above, unless noted otherwise.
• See procedure of this manual for fastener sizing information; for reference only.
Note: All torque values are in N-m unless otherwise stated.

Page 9
PROCEDURE
1. Swing the arms up and forward
until they stop.
Fig. 4
Fig. 5
2. Use a 16mm socket to install the four (4) pieces each of the M10 x 35mm hex head screws and M10 flat
washers to attach the seat pad to the frame.

Page 10
3. Remove the pivot shaft from the
frame prior to mounting the back
rest assembly. (Fig. 6)
4. Install the seat by lowering the
back rest assembly into position,
then inserting the shaft into the
frame and through the back-rest
assembly.
5. The shaft flats must align with
the set screws on either side
when mounting the back rest. (Fig.
7)
Fig. 6
Fig. 7
6. Use a 6mm allen key to secure one
(1) piece of the M8 x 16mm socket
screw into the user right side
bearing assembly.
7. Repeat this step for the user left
side.
Fig. 8

Page 11
TOOLS
Working on this product will require basic and/or sometimes specialty tools based on the type of service that
will be performed at any time. To assist, we recommend having the tools listed available when performing
maintenance.
Tool
Metric Allen Key Set Screwdriver Set, Phillips
Metric Open-Ended Wrench Set Screwdriver Set, Flat
Large Adjustable Crescent Wrench Torque Wrench
Metric Socket Set
MAINTAIN ALL EQUIPMENT: Preventative maintenance is the key to smooth operating equipment as well
as keeping the product in safe operating condition. Failure to conduct preventative maintenance by the owner
may cause the product to operate in an unsafe manner. Equipment needs to be inspected and maintained at
regular intervals per the preventative maintenance schedule provided in this manual.
Cleaning
Keeping your Strength units clean is an important component of preventative maintenance and the overall
aesthetics of your product. While your clients will appreciate clean equipment free of sweat, dirt and other
contaminants proper care and cleaning will extend the life of your product and reduce premature aging and
wear. See the maintenance schedule for recommended frequency.
Inspection
Visual inspection of your units will insure a safe environment for your clients and alert you to any issues that
may require maintenance prior to equipment failure. Proper, timely visual inspection is a critical component to
the long term care of your product.
• Fasteners, hardware and attachments should be checked monthly for looseness. Tighten as required
using appropriate tools.
• Handgrips should be checked for wear or damage monthly and replaced as needed.
• Main frame should be inspected every six months for signs of unusual wear, corrosion or structural
integrity issues.
MAINTENANCE

Page 12
MAINTENANCE SCHEDULE
With durable, high performance components, this equipment is designed for heavy usage with minimal
maintenance required. To keep it in top condition, perform regular daily, weekly and monthly preventive
maintenance routines outlined below.
The safety and integrity of this machine can only be maintained when the equipment is regularly examined for
damage and wear and repaired. It is the sole responsibility of the owner of this equipment to ensure that regular
maintenance is performed. Worn or damaged parts must be replaced immediately or the equipment removed
from service until the repair is made.
Daily Weekly Monthly Bi-Annually
Inspect
Fasteners X
Handgrips X
Labels X
Main Frame X
Cleaning
Main Frame X

Page 13
SUPPORT & SERVICE
For Technical Support, Service, Parts Orders or any Customer Service needs, please contact us direct by phone,
email, or through our 24 hour support site:
To help us support you, please provide the following information when requesting assistance with your equipment:
Facility Name & Address Product Serial Number Description of Issue
Our goal is to provide fast, reliable support to all your product support requests. We strive to answer all support
requests under an average hold time of 3 minutes, all support emails within 1 business day and all field service
requests within 48 hours.
PREVENTATIVE MAINTENANCE
Protect your product & assure it always runs like new with a Core Advantage Preventative Maintenance or Extended
Warranty Package. Contact your service manager for more information: [email protected]
To request access visit:
SUPPORT.COREHANDF.COM
• General Inquiries
• Warranty Registration
• Preventative Maintenance
• Service Requests
• Parts Orders
• Automated partner payment
• Product technical library
• Transparency on service performance
• Real time communication
OFFERS 24-HOUR SELF SERVICE ACCESS TO:
Core Connect is your portal to all things service! Whether you need to
order parts or register your warranty, Core Connect is the most effective
way to get what you need fast and keep your facility operating smoothly.
CORE CONNECT
GLOBAL SUPPORT CENTER
4400 NE 77th Avenue, Suite 300 Vancouver, WA 98662
Tel: [phone] • [phone] • [email protected]
Warranty information: https://corehandf.com/warranty

Page 14
THIS PAGE INTENTIONALLY BLANK

© 2020 CORE HEALTH & FITNESS LLC PART NUMBER 620-8651, REV C
All rights reserved. Star Trac, the Star Trac logo and StairMaster are registered trademarks of Core Health & Fitness, LLC. Schwinn and Nautilus are registered
trademarks of Nautilus Inc. used under license to Core Health & Fitness LLC. Throwdown is a registered trademark of Throwdown Industries, LLC.