Nautilus HDP6D-LFHR User manual

ASSEMBLY
MANUAL
CORE HEALTH & FITNESS
HDP6D-LFHR

Page 2
Before using this product, it is essential to read the ENTIRE Owner’s Manual and ALL
installation instructions. The Owner’s Manual describes equipment setup and instructs
members on how to use correctly and safely.
Read all warnings posted on the machine.
Health related injuries may result from incorrect or excessive use of exercise equipment.
Core Health & Fitness strongly recommends you to encourage your members to discuss their
health program or fitness regimen with a health care professional, especially if you or they
have not exercised for several years, are over 35, or have known health conditions.
WARNING!
IMPORTANT SAFETY INSTRUCTIONS
WARNING - to reduce the risk of injury to
person:
Fig. 1
1. Assemble and operate the machine on a solid
level surface. Position the machine with a
minimum of 24 inches (0.6 meters) of clearance
on each side to allow for ease of mounting and
dismounting.
The actual area for access and passage shall be
the responsibility of the facility and should take
into account this training envelope, Americans
with Disabilities Act Accessibility Guidelines
(ADAAG) requirements and any required local
codes or regulations (www.access-board.gov/
ada).
2. This equipment is designed for use in a
commercial gymnasium or health club. To ensure
the proper use of the equipment in a safe manner,
all users of the equipment should read this
manual before using the machine. This machine
should be made a part of your club training
program in order that the equipment is used by
your members in a safe manner as intended. In
addition to instructing the club members in the
proper use of the equipment, the club member
should obtain a complete physical examination
form their health care provider before beginning
any exercise program.
3. This machine is not intended to be used by
children. It is not intended to be used by persons
with reduced physical, sensory, or mental
capabilities or lack of experience and knowledge,
unless given instruction and under the personal
supervision concerning use of the machine by a
person responsible for their safety. Do not leave
children unsupervised around the machine.
4. The safety and integrity of this machine can only
be maintained when the equipment is regularly
examined for damage and wear and repaired.
It is the sole responsibility of the owner of this
equipment to ensure that regular maintenance
is performed. Worn or damaged parts must be
replaced immediately or the equipment removed
from service until the repair is made.

Page 3
5. All equipment MUST be secured (bolted and
tightened) to a solid, level surface, using all of
the anchoring holes provided, to stabilize and
eliminate rocking or tipping over. Shim any
mounting surface that does not rest thoroughly
on the floor using flat washers, DO NOT force the
foot to contact the ground with anchors.
Fasteners must have a minimum of 500 lbs.
tensile capacity, be a bolt of grade 2 or better
and be installed per the bolt manufacturer’s
specifications.
WARNING: Due to the wide variety of flooring
on which equipment may be anchored or installed
and differences in applicable local building codes,
Core Health & Fitness is not responsible for any
damage to the flooring that may result due to
anchoring or installing equipment to the floor and
for compliance with local building codes. Only
licensed contractors or certified installers should
be used to insure proper anchoring, installation,
and compliance with local building code.
6. Do not exceed the maximum allowable user
weight limit of:
• 350 lbs. (160 kg.)
7. It is the purchaser’s sole responsibility to properly
instruct its end users and supervising personnel
as to the proper operating procedures of all
equipment.
8. Caution: unit is heavy and requires two people
for assembly.
SAVE THESE INSTRUCTIONS

Page 4
This page shows examples of the warning labels and communication stickers placed on the equipment as part of the manufacturing process. It is critical that own-
ers maintain the integrity and placement of these stickers. If you find any stickers missing or damaged the replacement numbers are shown on the support site.
See Support and Service to order replacements. NOTE: STICKERS AND LABELS ARE NOT SHOWN TO SCALE
IMPORTANT LABEL LOCATIONS
Fig. 2

Page 5
PROCEDURE
1. Insert the tension rod (27-0876)
through the backing plate (27-0366)
into the rear platform insert.
NOTE: Insert and remove the tension
rod a few times to ensure it seats all the
way and to ensure no debris remains in
the rear platform hole.
Fig. 6
2. Slide the center platform section
into place against the rear platform
insert. Ensure that the tension rod
installed in Step 1 passes through
the hole in the center platform and
connects into the barrel nut located
inside the center platform.
Fig. 7
Required Tools:
• 11/16” Open-Ended Wrench
• 5/8” Open-Ended Wrench
• 3/4” Open-Ended Wrench
• 5/16” Allen Key
ASSEMBLY