NEC Univerge SV8100 User guide

System Hardware Manual
Doc. No. 10536
Issue 1.5

NEC shall not be liable for any direct, indirect, consequential or incidental
damages about the use of this equipment, manual or any related materials.
The information in this technical manual is advisory in nature and is subject to
change. NEC may make improvements and changes in the products described
in this manual without notice.
Changes is periodically made to the information in the new editions. Efforts have
been made to ensure that the contents of this manual are correct. Should you
find any error, NEC welcomes your comments to improve our communications.
Please contact NEC on 1800 036 136.
Contents of this manual are subject to change without prior notice at the
discretion of NEC Australia Pty Ltd.
This document has been prepared for the use of employees and customers of
NEC Australia Pty Ltd and may not be reproduced without prior written approval
of NEC Australia Pty Ltd.
Copyright © 2007
NEC Australia Pty Ltd
633 – 647 Springvale Road
Mulgrave Vic 3170

GENERAL
INFORMATION Congratulations! You have purchased the NEC SV8100 System.
The feature-rich SV8100 key system provides over 200 features including Computer
Telephony Integration, Least Cost Routing, Automatic Call Distribution, T1, ISDN-BRI
Voice Trunks, ISDN-PRI Voice Trunks, Voice over Internet Protocol, and many others.
The SV8100 system provides what the customer needs today, and as business
expands the system can be expanded to grow as well.
The SV8100 system has a set of manuals that provides all the information necessary to
install and support the system. This preface describes these manuals.
THIS MANUAL This manual contains detailed instructions to install the SV8100 chassis, Blades,
Multiline Terminals, and optional equipment in the following chapters.
Regulatory
This chapter provides important regulatory information.
Chapter 1 – Introduction to SV8100/SV8300
This chapter provides an overview of the UNIVERGE SV8100/SV8300 system.
Chapter 2 – SV8100 System Specifications
This chapter contains detailed specifications for the SV8100 system and should be
carefully reviewed by the technician before installing the system.
Chapter 3 – SV8300 System Specifications
This chapter contains detailed specifications for the SV8300 system and should be
carefully reviewed by the technician before installing the system.
Chapter 4 – Installing the SV8100 Chassis
This chapter contains the information necessary for installing the SV8100 chassis. The
technician should become familiar with this section before starting installation.
Preface

Chapter 5 – Installing the SV8300 Chassis
This chapter contains the information necessary for installing the SV8300 chassis. The
technician should become familiar with this section before starting installation.
Chapter 6 – Installing the SV8100/SV8300 Blades
This chapter contains instructions for installing the blades in the UNIVERGE
SV8100/SV8300 chassis.
Chapter 7 – Installing DT300/DT700 Series (DTL/ITL) Digital and IP Multiline
Terminals
This chapter provides information about the UNIVERGE SV8100/SV8300 system
digital and IP terminals in addition to the single line telephones, cordless telephones
and wireless telephones.
Chapter 8 – Installing SV8100/SV8300 Cordless Telephones
This chapter provides information regarding cordless telephones that can be used in
conjunction with the UNIVERGE SV8100/SV8300 system.
Chapter 9 – Installing SV8100/SV8300 Wireless Telephones
The wireless telephones provide wireless freedom that also allows access to features
provided by the UNIVERGE SV8100/SV8300 system.
Chapter 10 – Installing SV8100/SV8300 Conference Solutions
Conferencing solutions provide premium, full-duplex audio to small conference rooms
as a single unit or to larger rooms when expanded by up to three units that also expand
microphone access and loudspeaker coverage.
Chapter 11 – Installing SV8100/SV8300 Optional Equipment
This chapter provides information for installing optional equipment, such as
PGD(2)-U( ) ADPs, background music, door boxes, DSS consoles, Dterm VSR,
external paging as well as other handsets, recording devices and adapters on the
UNIVERGE SV8100/SV8300 digital and IP telephones.
Chapter 12 – Installing Dterm Series i Telephones
The UNIVERGE SV8100/SV8300 system supports several different IPK II Dterm Series i
Multiline Terminals and an Attendant Console. This chapter describes each terminal
and the console and provides instructions for attaching the terminals to the system
and for wall mounting.
Chapter 13 – Installing Dterm Series i Optional Equipment
The UNIVERGE SV8100/SV8300 system provides several adapters that allow
peripheral equipment to be attached to the IPK II Dterm Series i Multiline Terminals.
This chapter describes each adapter and provides applicable installation instructions.

SUPPORTING
DOCUMENTS Other manuals in the set are described below.
Documents supporting the SV8100 system include:
UNIVERGE SV8100 Features and Specifications Manual
This manual describes each available feature for the SV8100 system.
UNIVERGE SV8100 General Description Manual
This manual contains general information about the system features, configuration and
standards. This overview of the SV8100 system is useful when presenting information
to potential customers.
UNIVERGE SV8100 Programming Manual
This manual contains all programming instructions for the SV8100 system.
UNIVERGE SV8100 PC Programming Manual
This manual describes the operation of the PCPro program for the SV8100 system.
This program is a user-friendly Windows application that allows the user to program
and configure features of the SV8100 system from the PC environment.

Documents supporting the SV8300 system include:
UNIVERGE SV8300 System Manual
Contains the system description, hardware installation procedure and the programming
procedure of the SV8300 system.
UNIVERGE SV8300 Command Manual
Contains the Customer Administration Terminal (CAT) operation, command functions
and data required forprogramming the system and the Resident System Program.
UNIVERGE SV8300 Programming Manual
Contains procedure for programming each business, hotel, ISDN, OAI, WCS and WLAN
feature.
UNIVERGE SV8300 PC Programming Manual
Contains the functional description and the installation procedure for the PCPro.
UNIVERGE SV8300 System Data Programming Manual
Contains the Customer Specification Sheets and the System Data Programming Sheets.
UNIVERGE SV8300 NetworkingManual
Contains the system description and the programming procedure for the CCIS, Q-SIG
and Remote Unit System.
UNIVERGE SV8300 Maintenance Manual
Contains the system maintenance servicesand the recommended troubleshooting
procedure.
UNIVERGE SV8300 SMDR/MCI/PMS Interface Specifications
Contains the interface specifications for Station Message Detail Recording (SMDR),
Message Center Interface (MCI), Property Management System (PMS) and the PMS
operation.

SECTION 1ELECTROMAGNETIC INTERFERENCE (EMI)
WARNING
This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.
SECTION 2INCIDENCE OF HARM
If the System is malfunctioning, it may also be causing harm to the telephone network.
The Telephone system should be disconnected until the source of the problem can be
determined and until repair has been made. If this is not done, the Network Provider
may temporarily disconnect the service.
SECTION 3HEARING AID COMPATIBILITY
The NEC Multiline Terminals that are provided for this system are hearing aid
compatible. The manufacturer of Single Line Telephones for use with the system must
provide notice of hearing aid compatibility to comply with ACA Technical Standards.
SECTION 4SERVICE REQUIREMENTS
WARNING
This equipment must only be installed and maintained by service
personnel.
In the event of equipment malfunction, all repairs must be performed by an
authorised dealer of NEC Australia Pty Ltd or by NEC Australia Pty Ltd. It is
the responsibility of users requiring service to report the need for service to
one of NEC Australia Pty Ltd authorised agents or to NEC Australia Pty Ltd.
SECTION 5COMPLIANCE INFORMATION
This equipment has been tested to comply with all relevant ACA Technical
Standards.
To be compliant to Australian Standard ACIF S004:2001, Warning: Small metal objects
such as staples and pins may be caught and held in the earpiece and that the user
should be aware and careful to prevent any accident from such an event.
The UNIVERGE SV8100 KSU must be permanently connected to protective earth.
Regulatory

SECTION 6VOICE ANNOUNCEMENT/MONITORING
CAUTION
The use of monitoring, recording or listeningdevices to eavesdrop, monitor,
retrieve or record telephone conversations or other sounds activities,
whether or not contemporaneous with its transmission may be illegal in
certain circumstances under federal or state laws. Legal advise should be
sought prior to implementing any practice that monitors or records any
telephone conversation. Some federal and state laws require some form of
notification to all parties to the telephone conversation, such as using a
beep tone or other notification methods, or require the consent of all parties
to the telephone conversation, prior to monitoring or recording a telephone
conversation. Some of these laws incorporate strict penalties.
SECTION 7MUSIC ON HOLD
IMPORTANT NOTE
In accordance with Australian Copyright Law, a license may be required
from The Australian Performing Right Association Limited (APRA), or other
similar organisation, when radio or TV broadcasts are transmitted through
the Music On Hold feature of this telecommunication system. NEC
Australia Pty Ltd hereby disclaims any liability arising out of the failure to
obtain such a license.
SECTION 8ULREGULATORY INFORMATION
This equipment has been listed by Underwriters Laboratories and complies with all
applicable requirements of the standard for telephone equipment UL 1459.

SECTION 9BATTERY DISPOSAL AND SAFETY
The UNIVERGE SV8100 system includes the batteries listed below. When disposing of
these batteries from system chassis, blades or external battery boxes, the
maintenance personnel must comply with applicable Federal and State regulations
regarding proper disposal procedures.
IMPORTANT SAFEGUARDS FOR BATTERY DISPOSAL
DO NOT PLACE USED BATTERIES IN YOUR REGULAR TRASH!
THE PRODUCT YOU PURCHASED CONTAINS A LITHIUM OR SEALED
LEAD ACID BATTERY. LITHIUM OR SEALED LEAD ACID BATTERIES
MUST BE COLLECTED, RECYCLED OR DISPOSED OF IN AN
ENVIRONMENTALLY SOUND MANNER.
The incineration, landfilling or mixing of disposable batteries with the municipal solid
waste stream may be PROHIBITED BY LAW in most areas. Contact your local solid
waste management officials for other information regarding the environmentally sound
collection, recycling and disposal of the battery.
CAUTION
Danger of explosion if batteries are incorrectly installed. Replace only with
the same or equivalent type of battery as indicated throughout this manual.
Unit Name Type of Battery Quantity
CD-CP00-XX Lithium 1
CD-VM00 Lithium 1
CHS2U INT BATT (Optional) Sealed Lead Acid 2
CHS LARGE BATT BOX
(Optional) Sealed Lead Acid 1 BAT Box = 3 sets of [2 x 12V-7AH] 1 BAT Box = 6 sets of [2 x 12V-7AH]
1 BAT Box = 9 sets of [2 x 12V-7AH]
1 BAT Box = 12 sets of [2 x 12V-7AH]

System Hardware Manual i
Table of Contents
Chapter 1 Introduction to SV8100/SV8300
Section 1 General Information ..................................................................................... 1-1
Section 2 Equipment List ............................................................................................ 1-4
Chapter 2 SV8100 System Specifications
Section 1 General Information ..................................................................................... 2-1
Section 2 System Block Diagram ................................................................................ 2-1
Section 3 Maximum System Capacities ..................................................................... 2-4
3.1 System Configuration – SV8100 ...................................................... 2-5
Section 4 Licensing ..................................................................................................... 2-9
Section 5 Power-Based Calculator Chart .................................................................. 2-14
Section 6 System Requirements and Specifications ................................................. 2-16
6.1 Cabling ........................................................................................... 2-16
6.2 Power Requirements ..................................................................... 2-18
6.2.1 Power Supply Specifications ............................................ 2-18
6.2.2 Power Supply Consumption ............................................. 2-19
6.3 Environmental Conditions .............................................................. 2-19
6.3.1 Temperature and Humidity .............................................. 2-19
6.4 Outside Line Types ........................................................................ 2-20
6.5 Transmission, Network, and Control Specifications ....................... 2-20
6.5.1 Transmission .................................................................... 2-20
6.5.2 Network ............................................................................ 2-21
6.5.3 Control ............................................................................. 2-21
6.5.4 Dtermseries i Terminals and Equipment ........................... 2-21
6.6 Dialing Specifications ..................................................................... 2-22
6.6.1 Dial Pulse Address Signaling ........................................... 2-22
6.6.2 Dual-Tone Multifrequency (DTMF) Address Signaling .... 2-22
6.6.3 External Equipment Connection ...................................... 2-23
6.6.4 Music Source for Music on Hold via Chassis ................... 2-23
6.6.5 External Paging (Audio) ................................................... 2-23

Issue No. 1.5 UNIVERGE SV8100/SV8300
ii Table of Contents
6.6.6 External Tone Ringer/Night Chime Output ....................... 2-23
6.6.7 SMDR Output ................................................................... 2-23
6.6.8 PC Connection ................................................................. 2-24
6.6.9 Relay Contact ................................................................... 2-24
6.7 Battery Backup ............................................................................... 2-24
6.7.1 System Backup (Optional) ............................................... 2-24
6.7.2 Memory Backup ............................................................... 2-24
6.8 Weights and Dimensions ............................................................... 2-25
6.8.1 Tone Patterns ................................................................... 2-28
6.8.2 Multiline Terminal LED Flash Patterns ............................. 2-29
Section 7 Traffic Capacity .......................................................................................... 2-30
Chapter 3 SV8300 System Specifications
Section 1 General Information ..................................................................................... 3-1
Section 2 System Block Diagram ................................................................................ 3-1
Section 3 Maximum System Capacities ...................................................................... 3-5
3.1 System Configuration – SV8300 ...................................................... 3-7
Section 4 Licensing .................................................................................................... 3-13
Section 5 Power-Based Calculator Chart .................................................................. 3-14
Section 6 System Requirements And Specifications ................................................. 3-15
6.1 Cabling ........................................................................................... 3-15
6.2 Power Requirements ...................................................................... 3-17
6.2.1 Power Supply Specifications ............................................ 3-17
6.2.2 Power Supply Consumption ............................................. 3-19
6.3 Environmental Conditions .............................................................. 3-19
6.3.1 Temperature and Humidity ............................................... 3-19
6.4 Outside Line Types ........................................................................ 3-20
6.5 Transmission, Network, and Control Specifications ....................... 3-20
6.5.1 Transmission .................................................................... 3-20
6.5.2 Network ............................................................................ 3-21
6.5.3 Control .............................................................................. 3-21
6.5.4 Multiline Terminals and Equipment .................................. 3-21
6.5.5 Series i Terminals ............................................................ 3-22

UNIVERGE SV8100/SV8300 Issue No. 1.5
System Hardware Manual iii
6.6 Dialing Specifications ..................................................................... 3-22
6.6.1 Dial Pulse Address Signaling ........................................... 3-22
6.6.2 Dual-Tone Multifrequency (DTMF) Address Signaling .... 3-22
6.6.3 External Equipment Connection ...................................... 3-23
6.6.4 Music Source for Music on Hold via Chassis ................... 3-23
6.6.5 External Paging (Audio) ................................................... 3-24
6.6.6 External Tone Ringer/Night Chime Output ...................... 3-24
6.6.7 SMDR Output ................................................................... 3-24
6.6.8 PC Connection ................................................................. 3-24
6.6.9 Relay Contact .................................................................. 3-24
6.7 Battery Backup .............................................................................. 3-24
6.7.1 System Backup (Optional) ............................................... 3-24
6.7.2 Memory Backup ............................................................... 3-24
6.8 Weights and Dimensions ............................................................... 3-25
6.8.1 Weights ............................................................................ 3-25
6.8.2 Dimensions ...................................................................... 3-26
6.9 Audible and Visual Indication ......................................................... 3-27
6.9.1 Lamp Display ................................................................... 3-27
6.9.2 Tone Patterns .................................................................. 3-27
6.9.3 Multiline Terminal LED Flash Patterns ............................. 3-28
Section 7 Traffic Capacity .......................................................................................... 3-30
Chapter 4 Installing the SV8100 Chassis
Section 1 General Information ..................................................................................... 4-1
Section 2 Site Preparation and MDF/IDF Construction ............................................... 4-1
2.1 Precautionary Information ................................................................ 4-1
2.2 Surveying the Customer Site ........................................................... 4-2
2.3 Selecting the Best Location for Proper Installation .......................... 4-2
2.3.1 Selecting the Chassis Installation Site ............................... 4-2
2.3.2 Selecting a Permanent MDF Location ............................... 4-3
2.3.3 Selecting a Site for Installing the Telephones .................... 4-3
2.4 Constructing the Main Distribution Frame (MDF) ............................ 4-3
2.5 Power Failure Transfer ................................................................... 4-4
2.6 Fax CO Branch Connection ............................................................. 4-4

Issue No. 1.5 UNIVERGE SV8100/SV8300
iv Table of Contents
Section 3 Installing the Chassis ................................................................................... 4-5
3.1 Wall Mounting the 19” Chassis ........................................................ 4-6
3.1.1 CHS2U-AU Chassis Wall Mount Installation ...................... 4-6
3.2 Floor Mounting the 19” Chassis ..................................................... 4-13
3.2.1 CHS2U-AU Chassis Installation ....................................... 4-13
3.2.2 Multiple CHS2U-AU Chassis Installation ......................... 4-15
3.3 Stand Mounting the 19” Chassis .................................................... 4-17
3.3.1 CHS2U-AU Chassis Installation ....................................... 4-17
3.3.2 Multiple CHS2U-AU Chassis Installation ......................... 4-20
3.4 Rack Mounting the 19” Chassis ..................................................... 4-22
3.5 Installing the 19” Chassis ............................................................... 4-24
3.5.1 Unpacking the Equipment ................................................ 4-24
3.5.2 Before Installation ............................................................ 4-24
3.5.3 Installing the 19” Controlling Chassis ............................... 4-24
3.5.4 Installing Expansion Blades in the 19” Chassis
(Optional) ..................................................................... 4-25
3.5.5 Install 19” Chassis Grounding .......................................... 4-34
3.5.6 Install 19” Grounding on Multiple Chassis (Optional) ....... 4-35
3.5.7 Install AC Power Cords .................................................... 4-36
3.5.8 Install AC Power Cords on Multiple Chassis (Optional) ... 4-36
3.5.9 Install Additional Blades ................................................... 4-36
3.5.10 Apply Power to the 19” Chassis ....................................... 4-36
Section 4 Battery Connection .................................................................................... 4-37
4.1 Installing the Internal Batteries ....................................................... 4-37
4.2 Installing the External Batteries ...................................................... 4-42
4.2.1 Floor Mounting the CHS LARGE BATT BOX ................... 4-43
4.2.2 Battery Installation ............................................................ 4-44
4.2.3 CHS LARGE BATT BOX to CHS2U-AU Connection ....... 4-48
4.2.4 CHS LARGE BATT BOX Fuse Replacement .................. 4-51
Section 5 Power Supply ............................................................................................. 4-54
Section 6 Remove and Install Cooling Fan ................................................................ 4-54
6.1 CHS2U-AU Chassis ....................................................................... 4-54
6.1.1 Remove Cooling Fan .................................................... 4-54
6.1.2 Install Cooling Fan ........................................................... 4-56

UNIVERGE SV8100/SV8300 Issue No. 1.5
System Hardware Manual v
Chapter 5 Installing the SV8300 Chassis
Section 1 General Information ..................................................................................... 5-1
Section 2 Site Preparation and MDF/IDF Construction ............................................... 5-1
2.1 Precautionary Information ................................................................ 5-1
2.2 Surveying the Customer Site ........................................................... 5-2
2.3 Selecting the Best Location for Proper Installation .......................... 5-2
2.3.1 Selecting the Chassis Installation Site ............................... 5-2
2.3.2 Selecting a Permanent MDF Location ............................... 5-3
2.3.3 Selecting a Site for Installing the Telephones .................... 5-3
2.4 Constructing the Main Distribution Frame (MDF) ............................ 5-3
2.5 Power Failure Transfer .................................................................... 5-4
Section 3 Installing the Chassis ................................................................................... 5-5
3.1 Wall Mounting the 19” Chassis ........................................................ 5-7
3.1.1 CHS1U-AU and CHS2U-AU Chassis Installation .............. 5-7
3.2 Floor Mounting the 19” Chassis ..................................................... 5-17
3.2.1 CHS1U-AU Chassis Installation ....................................... 5-17
3.2.2 Multiple CHS2U-AU Chassis Installation ......................... 5-19
3.3 Stand Mounting the 19” Chassis .................................................... 5-20
3.3.1 CHS1U-AU+CHS2U-AUx1 Chassis Installation .............. 5-20
3.3.2 CHS1U-AU+CHS2U-AUxN Chassis Installation .............. 5-24
3.4 Rack Mounting the 19” Chassis ..................................................... 5-30
3.5 Installing the 19” Chassis ............................................................... 5-33
3.5.1 Unpacking the Equipment ................................................ 5-33
3.5.2 Before Installation ............................................................ 5-33
3.5.3 Installing the 19” Controlling Chassis .............................. 5-34
3.5.4 Installing the 19” Expansion Chassis ............................... 5-35
3.5.5 Installing Expansion Blades in the 19” Chassis
(Optional) ..................................................................... 5-35
3.5.6 Cable Connection between CPU Blades ......................... 5-44
3.5.7 Install 19” Chassis Grounding .......................................... 5-45
3.5.8 Install 19” Grounding on Multiple Chassis (Optional) ....... 5-45
3.5.9 Install AC Power Cords .................................................... 5-46
3.5.10 Install AC Power Cords on Multiple Chassis (Optional) ... 5-47
3.5.11 Install Additional Blades ................................................... 5-47
3.5.12 Apply Power to the 19” Chassis ....................................... 5-47

Issue No. 1.5 UNIVERGE SV8100/SV8300
vi Table of Contents
Section 4 Battery Connection .................................................................................... 5-47
4.1 Install Internal Batteries .................................................................. 5-47
4.1.1 Install Internal Batteries CHS1U-AU Chassis .................. 5-47
4.1.2 Install Internal Batteries CHS2U-AU Chassis .................. 5-52
4.2 Install External Batteries (without CHS LARGE BATT BOX) ......... 5-57
4.3 Install External Batteries (with CHS LARGE BATT BOX) .............. 5-61
4.3.1 45 Minutes Backup Time .................................................. 5-61
4.3.2 3 Hours Backup Time ....................................................... 5-62
4.3.3 CHS LARGE BATT BOX Fuse Replacement .................. 5-69
Section 5 Remove and Install Cooling Fan ................................................................ 5-72
5.1 CHS1U-AU Chassis ....................................................................... 5-72
5.1.1 Remove Cooling Fan ....................................................... 5-72
5.1.2 Install Cooling Fan ........................................................... 5-74
5.2 CHS2U-AU Chassis ....................................................................... 5-74
5.2.1 Remove Cooling Fan ....................................................... 5-74
5.2.2 Install Cooling Fan ........................................................... 5-76
Chapter 6 Installing the SV8100/SV8300 Blades
Section 1 General Information ..................................................................................... 6-1
1.1 Slot Locations ................................................................................... 6-1
Section 2 Installation ................................................................................................... 6-2
2.1 Installation and Safety Precautions .................................................. 6-2
2.2 Installing an Extension or Trunk Blade ............................................. 6-3
2.2.1 Installing the Blades ........................................................... 6-3
2.2.2 Order of Installing Extension Blades .................................. 6-4
2.2.3 Order of Installing Trunk Blades ......................................... 6-5
2.3 Remove an Extension or Trunk Blade ............................................. 6-6
2.4 Uninstalling a Blade Slot Through Software ..................................... 6-7
2.5 Blade Capacities .............................................................................. 6-7
2.6 Powering Up the SV8100 ................................................................. 6-7
2.6.1 Performing a Cold Start ...................................................... 6-7
2.6.2 Performing a Hot Start ....................................................... 6-8
2.6.3 Resetting the System ......................................................... 6-8
2.6.4 Performing a Software Upgrade ....................................... 6-11

UNIVERGE SV8100/SV8300 Issue No. 1.5
System Hardware Manual vii
Section 3 Common Control Blades ........................................................................... 6-13
3.1 CD-CP00-AU (SV8100 Central Processing Unit) .......................... 6-13
3.1.1 Description ....................................................................... 6-14
3.1.2 Installation ........................................................................ 6-17
3.1.3 Switch Settings ................................................................ 6-18
3.1.4 LED Indications ................................................................ 6-19
3.1.5 Connectors ....................................................................... 6-20
3.2 CC-CP00 (SV8300 Central Processing Unit) ................................ 6-22
3.2.1 Description ....................................................................... 6-23
3.2.2 Installation ........................................................................ 6-25
3.2.3 Switch Settings ................................................................ 6-26
3.2.4 LED Indications ................................................................ 6-27
3.2.5 Connectors ....................................................................... 6-28
3.3 PZ-ME50-AU (Memory Expansion Daughter Board) ..................... 6-31
3.3.1 Description ....................................................................... 6-31
3.3.2 Installation ........................................................................ 6-32
3.4 PZ-VM21 (Voice Mail Daughter Board) ........................................ 6-33
3.4.1 Description ....................................................................... 6-33
3.4.2 Installation ........................................................................ 6-35
3.4.3 Switch Settings ................................................................ 6-36
3.5 PZ-32IPLA/PZ-64IPLA/PZ-128IPLA (Voice over IP Daughter Boards) ..
6-37
3.5.1 Description ....................................................................... 6-37
3.5.2 Installation ........................................................................ 6-38
3.5.3 Switch Settings ................................................................ 6-38
3.5.4 LED Indications ................................................................ 6-39
3.5.5 Connectors ....................................................................... 6-40
Section 4 Station Blades ........................................................................................... 6-42
4.1 CD-8DLCA/CD-16DLCA (Digital Station Interface) ...................... 6-42
4.1.1 Description ....................................................................... 6-43
4.1.2 Installation ........................................................................ 6-44
4.1.3 LED Indications ................................................................ 6-44
4.1.4 Connectors ....................................................................... 6-44
4.2 PZ-8DLCB (Digital Station Daughter Board) .................................. 6-46
4.2.1 Description ....................................................................... 6-46
4.2.2 Installation ........................................................................ 6-46
4.2.3 PZ-8DLCB Daughter Board Cable Connection ................ 6-46

Issue No. 1.5 UNIVERGE SV8100/SV8300
viii Table of Contents
4.3 CD-4LCA/ CD-8LCA (4-Port/8-Port Single Line Interface) ............. 6-48
4.3.1 Description ....................................................................... 6-49
4.3.2 Installation ........................................................................ 6-50
4.3.3 Connectors ....................................................................... 6-51
4.4 PZ-4LCA/PZ-8LCE (4-Port/8-Port SLI Daughter Boards) .............. 6-52
4.4.1 Description ....................................................................... 6-53
4.4.2 Installation ........................................................................ 6-54
4.4.3 Connectors ....................................................................... 6-55
4.5 CD-LTA (Dterm/SLT Combination) .................................................. 6-56
4.5.1 Description ....................................................................... 6-56
4.5.2 Installation ........................................................................ 6-57
4.5.3 LED Indications ................................................................ 6-58
4.5.4 Connectors ....................................................................... 6-59
Section 5 Trunk Blades ............................................................................................. 6-60
5.1 CD-4COTC (4 Loop Start Trunk Interface) ................................... 6-60
5.1.1 Description ....................................................................... 6-60
5.1.2 Installation ........................................................................ 6-61
5.1.3 LED Indications ................................................................ 6-62
5.1.4 Connectors ....................................................................... 6-63
5.2 PZ-4COTG (4 Loop Start Trunk Interface Daughter Board) .......... 6-64
5.2.1 Description ....................................................................... 6-64
5.2.2 Installation ........................................................................ 6-65
5.2.3 Connectors ....................................................................... 6-66
5.3 CD-2BRIA (2 Basic Rate Interface) ................................................ 6-67
5.3.1 Description ....................................................................... 6-67
5.3.2 Installation ........................................................................ 6-68
5.3.3 LED Indications ................................................................ 6-69
5.3.4 Connectors ....................................................................... 6-69
5.4 PZ-2BRIA (2 Basic Rate Interface Daughter Board) ...................... 6-71
5.4.1 Description ....................................................................... 6-71
5.4.2 Installation ........................................................................ 6-72
5.4.3 Connectors ....................................................................... 6-73
5.5 CD-4DIOPA (OPX Telephone Interface) ........................................ 6-74
5.5.1 Description ....................................................................... 6-74
5.5.2 Installation ........................................................................ 6-75
5.5.3 LED Indications ................................................................ 6-75
5.5.4 Connectors ....................................................................... 6-75