NEC Univerge SV8100 User guide

System Hardware Manual
Issue 4.1 February 2011

THIS PAGE INTENTIONALLY LEFT BLANK

System Hardware Manual i
___________________________________________________________________________________
___________________________________________________________________________________
TABLE OF CONTENTS
Regulatory
Chapter 1 Introduction to SV8100
Section 1 General Information ....................................................................1-1
Section 2 Equipment List ............................................................................1-4
Chapter 2 SV8100 System Specifications
Section 1 General Information .....................................................................2-1
Section 2 System Block Diagram ................................................................2-1
Section 3 Maximum System Capacities ....................................................2-5
3.1 System Configuration – SV8100 .................................................2-6
Section 4 Power-Based Calculator Chart .................................................2-13
Section 5 System Requirements and Specifications ..............................2-16
5.1 Cabling ......................................................................................2-16
5.2 Power Requirements .................................................................2-19
5.2.1 Power Supply Specifications ....................................................2-19
5.2.2 Power Supply Consumption .....................................................2-20
5.3 Environmental Conditions ..........................................................2-20
5.3.1 Temperature and Humidity ......................................................2-20
5.4 Outside Line Types ....................................................................2-21
5.5 Transmission, Network, and Control Specifications ..................2-21

Issue 4.1 UNIVERGE SV8100
___________________________________________________________________________________
ii Table of Contents
___________________________________________________________________________________
5.5.1 Transmission ............................................................................2-21
5.5.2 Network ....................................................................................2-22
5.5.3 Control ......................................................................................2-22
5.5.4 Electra Elite IPK Terminals and Equipment .............................2-23
5.5.5 Series i Terminals ....................................................................2-24
5.6 Dialing Specifications .................................................................2-24
5.6.1 Dial Pulse Address Signaling ...................................................2-24
5.6.2 Dual-Tone Multifrequency (DTMF) Address Signaling .............2-24
5.6.3 External Equipment Connection ...............................................2-25
5.6.4 Music Source for Music on Hold via Chassis ...........................2-25
5.6.5 Music Source for Station Background Music via ACI ...............2-25
5.6.6 External Paging (Audio) ...........................................................2-25
5.6.7 External Tone Ringer/Night Chime Output ...............................2-26
5.6.8 SMDR Output ...........................................................................2-26
5.6.9 PC Connection .........................................................................2-26
5.6.10 Relay Contact ...........................................................................2-26
5.7 Battery Backup ..........................................................................2-26
5.7.1 System Backup (Optional) .......................................................2-26
5.7.2 Memory Backup .......................................................................2-26
5.8 Weights and Dimensions ...........................................................2-27
Chapter 3 Installing the SV8100 Chassis
Section 1 General Information .................................................................... 3-1
Section 2 Installing the Chassis ................................................................. 3-1
2.1 Wall Mounting the 19” Chassis ....................................................3-4
2.1.1 CHS2U Chassis Wall Mount Installation ....................................3-4
2.2 Floor Mounting the 19” Chassis .................................................3-12

UNIVERGE SV8100 Issue 4.1
System Hardware Manual - iii
___________________________________________________________________________________
___________________________________________________________________________________
System Hardware Manual iii
___________________________________________________________________________________
2.2.1 CHS2U Chassis Installation .....................................................3-12
2.2.2 Multiple CHS2U Chassis Installation .......................................3-14
2.3 Stand Mounting the 19” Chassis ...............................................3-16
2.3.1 CHS2U Chassis Installation .....................................................3-16
2.3.2 Multiple CHS2U Chassis Installation .......................................3-19
2.4 Rack Mounting the 19” Chassis .................................................3-22
2.5 Wall Mounting the 9.5” Chassis .................................................3-24
2.5.1 Option 1 ...................................................................................3-25
2.5.2 Option 2 ...................................................................................3-30
2.6 Stand Mounting the 9.5” Chassis ..............................................3-36
2.7 Installing the 19” Chassis ..........................................................3-39
2.7.1 Unpacking the Equipment ........................................................3-40
2.7.2 Before Installation ....................................................................3-40
2.7.3 Installing the 19” Controlling Chassis .......................................3-41
2.7.4 Installing Expansion Blades in the 19” Chassis (Optional) ......3-42
2.7.4.1 Connector Pin-Out on the PZ-BS10/PZ-BS11 ....................3-43
2.7.4.2 Install the PZ-BS10 Expansion Base Blade in the CHS2U Con-
trolling Chassis 3-43
2.7.4.3 Install the PZ-BS11 Expansion Blade in the CHS2U Expansion
Chassis 3-46
2.7.4.4 Connect the Controlling and Expansion Chassis ...............3-50
2.7.5 Install 19” Chassis Grounding ..................................................3-52
2.7.6 Install 19” Grounding on Multiple Chassis (Optional) ...............3-52
2.7.7 Install AC Power Cords ............................................................3-53
2.7.8 Install AC Power Cords on Multiple-Chassis (Optional) ...........3-54
2.7.9 Install Additional Blades ...........................................................3-54
2.7.10 Apply Power to the 19” Chassis ...............................................3-54
2.8 Installing the 9.5” Chassis .........................................................3-54
2.8.1 Install AC Power Cord 9.5” Chassis .........................................3-55

Issue 4.1 UNIVERGE SV8100
___________________________________________________________________________________
iv Table of Contents
___________________________________________________________________________________
2.8.2 Install Additional Blades 9.5” Chassis ......................................3-55
2.8.3 Apply Power to the 9.5” Chassis ..............................................3-55
Section 3 Battery Connection ................................................................... 3-56
3.1 Installing the Internal Batteries ..................................................3-56
3.2 Installing the External Batteries .................................................3-62
3.2.1 Floor Mounting the CHS LARGE BATT BOX ...........................3-62
3.2.2 Battery Installation ....................................................................3-64
3.2.3 CHS LARGE BATT BOX to CHS2U Connection .....................3-68
3.3 Installing the External Batteries 9.5” Chassis ............................3-72
3.3.1 Battery Installation ....................................................................3-72
3.3.2 CHSGW SMALL BATT BOX to CHS2U GW Connection ........3-74
3.3.3 CHSGW SMALL BATT BOX Fuse Replacement .....................3-75
Section 4 Remove and Install Cooling Fan .............................................. 3-77
4.1 CHS2U Chassis .........................................................................3-77
4.1.1 Remove Cooling Fan ............................................................3-77
4.1.2 Install Cooling Fan ...................................................................3-79
Chapter 4 Installing the SV8100 Blades
Section 1 General Information .................................................................... 4-1
1.1 Slot Locations ..............................................................................4-1
Section 2 Installation .................................................................................. 4-3
2.1 Installation and Safety Precautions .............................................4-3
2.2 Installing an Extension or Trunk Blade ........................................4-4
2.2.1 Installing the Blades ...................................................................4-4
2.2.2 Order of Installing Extension Blades ..........................................4-5

UNIVERGE SV8100 Issue 4.1
System Hardware Manual - v
___________________________________________________________________________________
___________________________________________________________________________________
System Hardware Manual v
___________________________________________________________________________________
2.2.3 Order of Installing Trunk Blades ................................................4-6
2.2.3.1 Installing CD-4COTA, CD-4DIOPB, CD-4ODTB or CD-2BRIA
blades 4-6
2.2.3.2 Installing CD-PRTA (T1/PRI) Blades ....................................4-8
2.3 Remove an Extension or Trunk Blade .........................................4-8
2.4 Uninstalling a Blade Slot Through Software ................................4-8
2.5 Blade Capacities ..........................................................................4-9
2.6 Powering Up the SV8100 ............................................................4-9
2.6.1 Performing a Cold Start .............................................................4-9
2.6.2 Performing a Hot Start .............................................................4-10
2.6.3 Resetting the System ...............................................................4-10
2.6.3.1 Initial Programming .............................................................4-10
2.6.3.2 Port Defaults .......................................................................4-11
2.6.3.3 Setting Up Extension Circuit Types ....................................4-11
2.6.3.4 Saving Your Configuration ..................................................4-12
2.6.3.5 Backing Up/Restoring a Database .....................................4-12
2.6.4 Performing a Software Upgrade ..............................................4-13
Section 3 Common Control Blades ..........................................................4-16
3.1 CD-CP00 (SV8100 Central Processing Unit) ............................4-16
3.1.1 Description ...............................................................................4-17
3.1.2 Installation ................................................................................4-20
3.1.3 Switch Settings ........................................................................4-22
3.1.4 LED Indications ........................................................................4-22
3.1.5 Connectors ...............................................................................4-24
3.2 PZ-ME50 (Memory Expansion Daughter Board) .......................4-27
3.2.1 Description ...............................................................................4-27
3.2.2 Installation ................................................................................4-28
3.3 PZ-VM21 (Voice Mail Daughter Board inc. V34 modem) .........4-30

Issue 4.1 UNIVERGE SV8100
___________________________________________________________________________________
vi Table of Contents
___________________________________________________________________________________
3.3.1 Description ...............................................................................4-30
3.3.2 Installation ................................................................................4-31
3.3.3 Switch Settings .........................................................................4-33
3.3.4 Remote PC Programming access ............................................4-33
3.4 PZ-32IPLA/PZ-64IPLA/PZ-128IPLA (Voice over IP Daughter
Boards) 4-33
3.4.1 Description ...............................................................................4-35
3.4.2 Installation ................................................................................4-36
3.4.3 Switch Settings .........................................................................4-36
3.4.4 LED Indications ........................................................................4-37
3.4.5 Connectors ...............................................................................4-38
3.5 PZ-32IPLB/PZ-64IPLB/PZ-128IPLB (Voice over IP Daughter
Boards) - (Available June 2011) 4-39
3.5.1 Description ...............................................................................4-39
3.5.2 Installation ................................................................................4-40
3.5.3 Switch Settings .........................................................................4-40
3.5.4 LED Indications ........................................................................4-40
3.5.5 Connectors ...............................................................................4-42
Section 4 Station Blades ........................................................................... 4-44
4.1 CD-8DLCA/CD-16DLCA (Digital Station Interface) ..................4-44
4.1.1 Description ...............................................................................4-45
4.1.2 Installation ................................................................................4-46
4.1.3 LED Indications ........................................................................4-46
4.1.4 Connectors ...............................................................................4-47
4.2 PZ-8DLCB (Digital Station Daughter Board) .............................4-49
4.2.1 Description ...............................................................................4-49
4.2.2 Installation ................................................................................4-50
4.2.3 PZ-8DLCB Daughter Board Cable Connection ........................4-50

UNIVERGE SV8100 Issue 4.1
System Hardware Manual - vii
___________________________________________________________________________________
___________________________________________________________________________________
System Hardware Manual vii
___________________________________________________________________________________
4.3 CD-4LCA/ CD-8LCA (4-Port/8-Port Single Line Interface) ........4-52
4.3.1 Description ...............................................................................4-53
4.3.2 Installation ................................................................................4-55
4.3.3 LED Indications ........................................................................4-55
4.3.4 Connectors ...............................................................................4-57
4.4 PZ-4LCA/PZ-8LCE (4-Port/8-Port SLI Daughter Boards) .........4-58
4.4.1 Description ...............................................................................4-60
4.4.2 Installation ................................................................................4-61
4.4.3 Connectors ...............................................................................4-62
4.5 CD-LTA (Dterm/SLT Combination) .............................................4-63
4.5.1 Description ...............................................................................4-63
4.5.2 Installation ................................................................................4-64
4.5.3 LED Indications ........................................................................4-65
4.5.4 Connectors ...............................................................................4-66
Section 5 Trunk Blades ..............................................................................4-67
5.1 CD-4COTA (4 Loop Start Interface) ..........................................4-67
5.1.1 Description ...............................................................................4-67
5.1.2 Installation ................................................................................4-69
5.1.3 LED Indications ........................................................................4-69
5.1.4 Connectors ...............................................................................4-70
5.2 PZ-4COTE (4 Loop Start Interface Daughter Board) ................4-71
5.2.1 Description ...............................................................................4-71
5.2.2 Installation ................................................................................4-73
5.2.3 Connectors ...............................................................................4-73
5.3 CD-2BRIA (2 Basic Rate Interface) ...........................................4-75
5.3.1 Description ...............................................................................4-75
5.3.2 Installation ................................................................................4-76

Issue 4.1 UNIVERGE SV8100
___________________________________________________________________________________
viii Table of Contents
___________________________________________________________________________________
5.3.3 LED Indications ........................................................................4-77
5.3.4 Connectors ...............................................................................4-78
5.3.5 Termination Switch Settings .....................................................4-78
5.4 PZ-2BRIA (2 Basic Rate Interface Daughter Board) .................4-80
5.4.1 Description ...............................................................................4-81
5.4.2 Installation ................................................................................4-81
5.4.3 Connectors ...............................................................................4-82
5.4.4 Termination Switch Settings .....................................................4-83
5.5 CD-4DIOPB (DID/OPX Interface) ..............................................4-84
5.5.1 Description ...............................................................................4-84
5.5.2 Installation ................................................................................4-85
5.5.3 LED Indications ........................................................................4-85
5.5.4 Connectors ...............................................................................4-86
5.6 CD-PRTA (PRI Interface) .........................................................4-87
5.6.1 Description ...............................................................................4-87
5.6.2 Installation ................................................................................4-88
5.6.3 LED Indications ........................................................................4-90
5.6.4 Connectors ...............................................................................4-92
5.7 CD-4ODTB (4-Port Tie Line Interface Blade) ............................4-94
5.7.1 Description ...............................................................................4-94
5.7.2 Installation ................................................................................4-95
5.7.3 LED Indications ........................................................................4-96
5.7.4 Connectors ...............................................................................4-96
5.7.5 Connections .............................................................................4-98
Section 6 Optional Blades ....................................................................... 4-100
6.1 CD-PVAA (Conference Bridge) (Future Enhancement) ..........4-100
6.1.1 Description .............................................................................4-100

UNIVERGE SV8100 Issue 4.1
System Hardware Manual - ix
___________________________________________________________________________________
___________________________________________________________________________________
System Hardware Manual ix
___________________________________________________________________________________
6.1.2 Installation ..............................................................................4-101
6.1.3 Switch Settings ......................................................................4-101
6.1.4 LED Indications ......................................................................4-101
6.1.5 Connectors .............................................................................4-102
6.2 CD-RTB (4-Port ) .....................................................................4-103
6.2.1 Description .............................................................................4-103
6.2.2 Installation ..............................................................................4-105
6.2.3 LED Indications ......................................................................4-105
6.3 CD-ETIA (Gigabit PoE Switch) ................................................4-106
6.3.1 Description .............................................................................4-106
6.3.2 Installation ..............................................................................4-107
6.3.2.1 Stacking Architecture ........................................................4-107
6.3.2.2 CD-CP00IP Address Assignment .....................................4-108
6.3.2.3 Group Formation ..............................................................4-108
6.3.2.4 Port Number Determination ..............................................4-108
6.3.2.5 Unmanaged Switch Functions ..........................................4-109
6.3.3 LED Indications ......................................................................4-109
6.3.4 Connectors .............................................................................4-109
Chapter 5 Installing DT300/DT700 Series (DTL/ITL) Digital and IP
Multiline Terminals
Section 1 General Description ....................................................................5-1
Section 2 DT300 Series Digital Multiline Terminals ..................................5-7
2.1 Digital MultilineTerminals .............................................................5-7
2.1.1 DTL-2E-1 (BK) TEL ....................................................................5-7
2.1.2 DTL-6DE-1 (BK) TEL .................................................................5-8
2.1.3 DTL-8LD-1 (BK) TEL/DTL-8LD-1 (WH) TEL ..............................5-8
2.1.4 DTL-12BT-1 (BK) TEL ...............................................................5-9

Issue 4.1 UNIVERGE SV8100
___________________________________________________________________________________
xTable of Contents
___________________________________________________________________________________
2.1.5 DTL-12D-1 (BK) TEL/DTL-12D-1 (WH) TEL ............................5-10
2.1.6 DTL-12PA-1 (BK) TEL .............................................................5-11
2.1.7 DTL-24D-1 (BK) TEL/DTL-24D-1 (WH) TEL ............................5-12
2.1.8 DTL-32D-1 (BK) TEL/DTL-32D-1 (WH) TEL ............................5-13
Section 3 DT700 Series IP Multiline Terminals ........................................ 5-15
3.1 IP MultilineTerminals .................................................................5-15
3.1.1 ITL-2E-1 (BK) TEL ...................................................................5-15
3.1.2 ITL-6DE-1 (BK) TEL .................................................................5-16
3.1.3 ITL-8LD-1 (BK) TEL/ITL-8LD-1 (WH) TEL ...............................5-16
3.1.4 ITL-12D-1 (BK) TEL/ITL-12D-1 (WH) TEL ...............................5-17
3.1.5 ITL-12PA-1 (BK) TEL ...............................................................5-18
3.1.6 ITL-24D-1 (BK) TEL/ITL-24D-1 (WH) TEL ...............................5-19
3.1.7 ITL-32D-1 (BK) TEL/ITL-32D-1 (WH) TEL ...............................5-20
3.1.8 ITL-320C-1 (BK) TEL ...............................................................5-21
Section 4 Install Multiline Terminals ........................................................ 5-23
4.1 Connecting the DT300 Series Multiline Terminal to the System 5-23
4.2 Applying Power to the DT700 Multiline Terminals .....................5-24
4.3 Connecting the IP Multiline Terminal to the Network and PC ....5-25
4.4 Adjusting the LCD on the Multiline Terminal ..............................5-26
4.5 Installing Line Key Kit (12LK-L KIT) ...........................................5-27
4.5.1 Installing the 12LK-L KIT ..........................................................5-27
4.5.2 Configuring the Digital Telephone for the Correct Number of Line
Keys 5-31
4.5.3 Configuring the IP Telephone for the Correct Number of Line Keys
5-31
4.6 Installing the Directory Card on the Multiline Terminal ..............5-33
4.7 Installing a Numbered Keypad on the Multiline Terminal ..........5-34

UNIVERGE SV8100 Issue 4.1
System Hardware Manual - xi
___________________________________________________________________________________
___________________________________________________________________________________
System Hardware Manual xi
___________________________________________________________________________________
4.7.1 Installing the Numbered Keypad on a Multiline Terminal ........5-36
4.7.2 Configuring the Digital Telephone for the Numbered Keypad .5-38
4.7.3 Configuring the IP Telephone for the Numbered Keypad ........5-38
4.8 Adjusting the Height on the Multiline Terminal ..........................5-40
4.9 Removing or Installing the Tilt Legs on the Multiline Terminal ..5-41
4.9.1 Remove Tilt Legs .....................................................................5-41
4.9.2 Install Tilt Legs .........................................................................5-42
4.10 Wall Mounting the Multiline Terminal .........................................5-44
4.10.1 Wall Mounting a Multiline Terminal using the Base Plate ........5-44
4.10.1.1 Adjusting the Hanger Hook .................................................5-44
4.10.1.2 Wall Mounting the Multiline Terminal ..................................5-45
4.10.1.3 Removing the Multiline Terminal from the Wall Mounted Base
Plate. 5-46
4.10.1.4 Wall Mounting the Base on a Switch Box ...........................5-47
Section 5 Multiline Terminals Optional Equipment .................................5-48
5.1 DT300/DT700 Series Terminal Options ....................................5-48
5.2 DT300/DT700 Series Optional Terminal Equipment .................5-49
5.2.1 8LK-L (BK) UNIT/8LK-L (WH) UNIT ........................................5-49
5.2.1.1 Installing the 8LK-L UNIT ...................................................5-49
5.2.2 8LKD (LD)-L (BK) UNIT/8LKD (LD)-L (WH) UNIT ...................5-51
5.2.2.1 Installing the 8LKD (LD)-L UNIT .........................................5-52
5.2.3 8LKI (LD)-L (BK) UNIT/8LKI (LD)-L (WH) UNIT ......................5-55
5.2.3.1 Installing the 8LKI (LD)-L UNIT ..........................................5-56
5.2.4 DCL-60-1 (BK) CONSOLE/DCL-60-1 (WH) CONSOLE .........5-59
5.2.4.1 Installing the DCL-60-1 CONSOLE ....................................5-60
5.2.5 LCD (BL)-L (BK) UNIT/LCD (BL)-L (WH) UNIT .......................5-64
5.2.6 PANEL( )-L UNIT ....................................................................5-65
5.2.7 WM-L UNIT Attached to Wall ...................................................5-65
5.2.8 Release the WM-L UNIT ..........................................................5-67

Issue 4.1 UNIVERGE SV8100
___________________________________________________________________________________
xii Table of Contents
___________________________________________________________________________________
5.2.9 WM-L UNIT Attached to Wall Plate ..........................................5-68
5.2.10 Removing the Multiline Terminal from the Wall Mounted Plate. .....
5-70
Section 6 Optional Handsets .................................................................... 5-71
6.1 ITL / DTL PTM Handset .............................................................5-71
6.2 ITL / DTL PTT Handset ..............................................................5-71
6.3 UTR-1-1 USB Handset ..............................................................5-72
6.3.1 Handset Connection .................................................................5-72
6.3.2 USB Connection .......................................................................5-72
6.3.3 Wall Mounting ..........................................................................5-73
Section 7 Bluetooth Cordless Handset .................................................... 5-74
7.1 Bluetooth Cordless Handset (BCH) Interface ............................5-74
7.2 Selecting a Location ..................................................................5-75
7.3 Controls and Indicators ..............................................................5-76
7.4 Installing the Bluetooth Cordless Handset .................................5-78
7.4.1 Installing the Bluetooth Handset Cradle ...................................5-78
7.4.2 Wall Mounting the Bluetooth Cradle .........................................5-84
7.4.3 Remove and Replace Handset Battery ....................................5-87
Section 8 Bluetooth Hub Adapter ............................................................. 5-88
8.1 Bluetooth Hub Adapter (BHA) Features ....................................5-88
8.1.1 Installing the BHA-L UNIT ........................................................5-88
8.1.2 Pairing a Bluetooth Device and Multiline Terminal (Bluetooth In-
stalled) 5-90
8.1.2.1 Accessing the Bluetooth Device Setup Screen .................. 5-90
8.1.2.2 Entering a PIN Code .......................................................... 5-90
8.1.2.3 Pairing ................................................................................ 5-90
8.1.2.4 Connecting the Paired Device ........................................... 5-91

UNIVERGE SV8100 Issue 4.1
System Hardware Manual - xiii
___________________________________________________________________________________
___________________________________________________________________________________
System Hardware Manual xiii
___________________________________________________________________________________
8.1.2.5 Unpairing ............................................................................5-91
8.1.2.6 Visibility Setting ..................................................................5-91
8.1.2.7 BT Information ....................................................................5-92
Section 9 Single Line Telephone ..............................................................5-93
9.1 Installing the SLT Adapter .........................................................5-93
9.2 Wall-Mounting the SLT Adapter ................................................5-94
Chapter 6 Installing SV8100 Optional Equipment
Section 1 General Information ....................................................................6-1
Section 2 PGD(2)-U10 ADP ..........................................................................6-1
2.1 Using a PGD(2)-U10 ADP ...........................................................6-1
2.2 LED Indications ...........................................................................6-2
2.3 Setting up PGD(2)-U10 ADP Connections ..................................6-2
Section 3 Background Music ....................................................................6-10
3.1 Installing Background Music ......................................................6-10
Section 4 Door Box ....................................................................................6-11
4.1 Installing a Door Box .................................................................6-11
Section 5 External Paging .........................................................................6-15
5.1 External Page ............................................................................6-15
5.2 Installing an External Page System ...........................................6-15
Section 6 External Paging and Door Box/Page Relays ...........................6-17
6.1 External Page Relays ................................................................6-17
6.2 Door Box /External Page Relay Contacts ..................................6-18
6.2.1 Connecting a Contact Relay Device to a Door Box/External Page
Relay 6-18

Issue 4.1 UNIVERGE SV8100
___________________________________________________________________________________
xiv Table of Contents
___________________________________________________________________________________
Section 7 External Recording System/External Ringer .......................... 6-19
7.1 External Recording System or External Ringer .........................6-19
7.2 Installing an External Recording System or External Ringer .....6-20
7.3 Programming .............................................................................6-21
Section 8 Music Sources ........................................................................... 6-24
8.1 Music on Hold ............................................................................6-24
8.2 Installing External Music on Hold ...............................................6-24
Section 9 Night Mode Selection ................................................................ 6-27
9.1 Night Mode Selector Switch .......................................................6-27
9.2 Connecting a Night Mode Selector Switch ................................6-27
Section 10 Telephone Labeling .................................................................. 6-27
10.1 DESI Printer Sheets ...................................................................6-27
10.1.1 Removing the Faceplate ..........................................................6-28
10.1.2 Replacing the Faceplate ..........................................................6-28
Section 11 Telephone Adapters .................................................................. 6-29
11.1 Using Adapters ..........................................................................6-29
11.2 In-line Power Adapter (ILPA-R) .................................................6-29
11.2.1 Conditions ................................................................................6-30
11.2.2 Installation ................................................................................6-31
11.3 ADA-L UNIT ...............................................................................6-33
11.3.1 ADA-L UNIT Switch Settings ....................................................6-34
11.3.2 Installing the ADA-L UNIT ........................................................6-35
11.3.3 ADA-L UNIT Connection ..........................................................6-37
11.3.3.1 ADA-L UNIT Connection for Recording Only ..................... 6-37
11.3.3.2 ADA-L UNIT Connection for Sending Recorded Calls to the

UNIVERGE SV8100 Issue 4.1
System Hardware Manual - xv
___________________________________________________________________________________
___________________________________________________________________________________
System Hardware Manual xv
___________________________________________________________________________________
Telephone 6-38
11.4 APR-L UNIT ...............................................................................6-38
11.4.1 APR-L UNIT Switch Settings ...................................................6-39
11.4.2 Installing the APR-L UNIT ........................................................6-40
11.5 PSA-L (BK) UNIT / PSA-L (WH) UNIT ......................................6-43
11.5.1 Installing the PSA-L Adapter ....................................................6-44
11.5.2 Using the PSA-L Adapter .........................................................6-50
11.6 Gigabit Adapter (GBA-L UNIT) ..................................................6-51
11.6.1 Installing the GBA-L UNIT ........................................................6-52
11.6.2 GBA-L UNIT Connection ..........................................................6-60
11.6.3 LED Display .............................................................................6-60
Section 12 Power Failure Telephones ........................................................6-61
12.1 Power Failure ............................................................................6-61
12.2 Connector Pin-Outs on COIU Blade for Power Failure Circuits 6-62
12.3 Installing the Power Failure Telephones ...................................6-62

Issue 4.1 UNIVERGE SV8100
___________________________________________________________________________________
xvi Table of Contents
___________________________________________________________________________________

System Hardware Manual R-1
BATTERY DISPOSAL
The UNIVERGE SV8100 system includes the batteries listed below. When disposing of these
batteries, Chassis, and/or Blades, you must comply with applicable regulations regarding proper
disposal procedures.
The UNIVERGE SV8100 CD-CP00 provides memory backup for approximately three years. The
Lithium battery should be replaced every two years.
IMPORTANT SAFEGUARDS FOR BATTERY DISPOSAL
DO NOT PLACE USED BATTERIES IN YOUR REGULAR WASTE! THE PRODUCT YOU
PURCHASED CONTAINS LITHIUM, NICKEL-CADMIUM OR SEALED LEAD BATTERIES. LITHIUM,
NICKEL-CADMIUM OR SEALED LEAD BATTERIES MUST BE COLLECTED, RECYCLED, OR
DISPOSED OF IN AN ENVIRONMENTALLY SOUND MANNER.
Table R-1 Battery Types and Quantities for Chassis and Blades
Unit Name Type of Battery Quantity
CD-CP00 Lithium 1
CHS LARGE BATT SET Sealed Lead 6
Internal Batteries Sealed Lead 2
Bluetooth® Cordless Handset Lithium-ion 1
G955 Wireless Lithium-ion 1
CHSGW SMALL BATT SET Sealed Lead 2
MH240 Wireless Lithium-ion 1
Regulatory

Issue 4.1 UNIVERGE SV8100
R-2 Regulatory
The incineration, landfilling or mixing of nickel-cadmium or sealed lead batteries with the municipal solid
waste stream is PROHIBITED BY LAW in most areas. Contact your local solid waste management
officials for other information regarding the environmentally sound collection, recycling, and disposal of
the battery.
Nickel-Cadmium (or sealed lead) batteries must be returned to an approved nickel-cadmium (or sealed
lead) battery recycler. This may be where the batteries were originally sold or a local seller of automotive
batteries. Contact your local waste management officials for other information regarding the
environmentally sound collection, recycling and disposal of the battery contained in this product.
The packaging for the UNIVERGE SV8100 system contains the following labels regarding proper
disposal.
PRODUCT PACKAGE LABELING
CONTAINS NICKEL-CADMIUM BATTERY.
BATTERY MUST BE RECYCLED OR
DISPOSED OF PROPERLY. MUST NOT BE
DISPOSED OF IN MUNICIPAL WASTE.
CONTAINS SEALED LEAD BATTERY.
BATTERY MUST BE RECYCLED. MUST NOT
BE DISPOSED OF IN MUNICIPAL WASTE.
Pb
Ni-Cd
CONTAINS NICKEL-METAL HYDRIDE
BATTERY. BATTERY MUST BE RECYCLED
OR DISPOSED OF PROPERLY. MUST NOT
BE DISPOSED OF IN MUNICIPAL WASTE.
Ni-MH