Neilsen CT2737 User manual

12PCS SPRAY GUN KIT CT2737
ORIGINAL INSTRUCTIONS
SAVE THESE INSTRUCTIONS AND PRECAUTIONS.
READ ALL PRECAUTONS AND INSTRUCTIONS BEFORE USE.
Cannon Tools Limited
Address: 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.

2
EC DECLARATION OF CONFORMITY
We CANNON TOOLS LTD
20 Station road, Rowley Regis, West Midlands,B65 0JU.U.K.
Declare that the following machine complies with the appropriate basic safety and
health requirements of the EC Directive based on its design and type, as brought
into circulation by us.
In case of alteration of the machine, not agreed upon by us, this declaration will
lose its validity.
Product description: 12PCS SPRAY GUN KIT
Model: CT2737
Applicable EC Directives:
EC Machinery Directive 2006/42/EC(machinery)
Harmonized standards
EN ISO 12100:2010, EN ISO 11148-10:2011
20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.
Mr. Gurcharan Tony Singh Sanghera
Managing Director
CANNON TOOLS LTD
2020-07-10

3
IMPORTANT SAFETY INFORMATION
Read and understand and follow all instructions and warnings before operating this
tool.
1. Be sure air is in OFF position when connecting tool to air supply.
2. Always wear approved eye protection when using tools.
3.Use only those accessories that are designed for use with tools.
4.Be sure to disconnect tool from air supply before changing accessories, performing
service on tool, and when not in use.
5. As with any tool, use common sense when operating.
6. Operate tool a safe distance from yourself and others in the work area.
7. The noise emission (sound pressure level) at the workplace may exceed the
normal standard. In this case, a quality ear protector should be used.
8. Be sure that the air hose is sufficiently long enough and not too long.
9. Superfluous hose lying on the floor can be a tripping hazard and so serious
Features and technical data
●
Nozzle (0.8-1.7mm),
●
100/1000/1000ml Aluminium containers
●
Air consumption: 6-10cfm
●
Pressure: 35-43psi
●
Air Inlet:1/4’’ BSP
●
2 HVLP spray guns
●
Mini Spray Gun
●
2 Regulators

4
1. Putting into operation
Before putting into operation, and especially after any repair work, check to see
that all nuts and bolts are tight. Always disconnect the unit from the air supply
before carrying out any repair work.
a) Mount the nozzle set tightly align the air nozzle so that the number stamped into it
can be read from the front the right way round.
b) Blow out the air hose before attaching it to the air connection (1/4’’)
c) The paint spray gun has been treated with an anticorrosive agent before leaving
the factory and must therefore get flushes out thoroughly with thinner before use
2. Adjusting the volume of air using the compressed- air micrometer
The air supply can be regulated extremely fine to suit all operational conditions,
micrometer in vertical position (parallel to gun body) =maximum atomization.
Micrometer in horizontal position (across gun body) = minimum atomization (for
blending etc) During operation, never remove hollow(item 12) by using the small
hollow key in order to remove the micrometer.
3. Reduction of the material volume
The volume of material following from the nozzle and thus the needle stroke can
be reduced steplessly by screwing in the material-volume regulation screw.
4. Changing the nozzle set
Always change the complete nozzle set whenever changing nozzle size. These
components, that consist of air cap, fluid nozzle and paint needle, are supplied as
a complete set. Insert paint nozzle before paint needle.
5. Exchanging the air piston and air piston packing
To replace the air piston remove the hollow screw and detach the air micrometer.
Pull out spring and air piston exchange the air piston unscrew stuffing box screw
and remove the old packing, now insert new packing with flat and first and gently
tighten stuffing box screw towards packing.
6. Cleaning and maintenance
a) Flush the material –conveying parts of the gun thoroughly with thinner.
b) Clean the air nozzle with a paint brush or brush. Do not immerse the nozzle in

5
thinner.
c) Under no circumstances try to clean clogged orifices using an unsuitable tool,
since the slightest amount of damage
PARTS DIAGRAM

6
No Description No Description
1 Air chuck 19 regulating nut
2 Fluid nozzle 20 Control knob
3 Brass ring 21 Screw
4 gasket 22 E-ring
5 nozzle screw 23 E-ring
6 Spring 24 Pin
7 seal 25 Pin
8 Connector 26 Valve
9 Needle 27 Filler
10 Spring 28 Cup
11 Lock knob 29 Cover
12 Control knob 30 Screw
13 screw 31 Air adjuster
14 Ring 32 screw
15 screw 33 Connector
16 O-ring 34 Spanner
17 needle 35 Spanner wrench
18 spring
CANNON TOOLS LTD
Add: 20 station road, Rowley Regis, west midlands,B65 0JU.U.K.
Made in China