NETGEAR ProSafe GSM7328 User manual

1UICK)NSTALLATION'UIDE
7300S Series Stackable Managed Switch
Follow these quick steps to install your switch.
You can also consult the full hardware installation guide on the Resource CD.
Verify the Following Package Contents
• 7300S Series Stackable Managed Switch
• Rubber footpads for tabletop installation
• Power cord
• Null-modem console cable
• Rack-mount kit for installing the switch in the rack
• This Installation Guide
•CDROM
• Warranty and Support Information Cards
If any item is missing or damaged, contact your place of purchase immediately.
Set Up the Switch
Prepare the site so that the mounting, access, power source, and environmental
requirements identified in the Hardware Installation Guide published on the CD-ROM are
met.
1. Install the switch.
• Installing the Switch on a Flat Surface: Stick one of the rubber footpads that
came with the switch on each of the four concave spaces on the bottom of the
switch.
• Installing the Switch in a Rack: Use the rack-mount kit supplied with your
switch.
2. Apply AC Power
When you apply power, the Power LED on the switch’s front panel will be Yellow, as
it conducts a Power On Self Test (POST). After the switch passes the POST, the
Power LED will change to Green and the switch is functional and ready to pass data.
If the POST fails, the Power LED will stay Yellow.
If the Power LED does not go on, check that the power cable is plugged in correctly
and that the power source is good. If this does not resolve the problem, refer to
Appendix B, Troubleshooting, in the Hardware Installation Guide on the CD-ROM.
3. Connect Devices to the Switch
Use Category 5 (Cat5) cable to connect devices.
SFP modules ship separately. If you need instructions on installing an SFP module,
please refer to the Hardware Installation Guide on the CD-ROM.
Perform the Initial Configuration
To configure the IP address, you must first access the Command Line management utility
via the console interface. You can connect to it using a VT100/ANSI terminal or a PC,
Apple Macintosh, or UNIX workstation that is directly connected to the switch’s console
port.
Establish a Console Session and Log In to the Switch
1. To connect a console to the switch:
• Using the null-modem cable supplied with the switch, connect a VT100/ANSI
terminal or a workstation to the switch port labeled Console.
• If you attached a PC, Apple Macintosh, or UNIX workstation, start a terminal-
emulation program:
• Windows users can use HyperTerminal.
• Macintosh users can use ZTerm.
• UNIX users can use a terminal emulator like TIP.
2. Configure the terminal-emulation program to use the following settings:
• Baud rate: 9,600 bps
• Data bits: 8
• Parity: none
• Stop bit: 1
• Flow control: none
These settings appear below the connector on the switch front panel.
3. The switch is shipped using DHCP protocol by default, so that the management IP
address is assigned automatically from a DHCP server. To see the assigned IP
address, log in to the switch with the user name of either admin or guest, and type the
show network command. If you wish to assign the switch IP address manually,
please use the procedure that follows.

January 2006
©2005 by NETGEAR, Inc. All rights reserved.
NETGEAR is a registered trademark of NETGEAR, Inc. in the United States and/or other countries.
Other brand and product names are trademarks or registered trademarks of their respective holders. Information
is subject to change without notice.
Manually Set a Static IP Address for the Management CPU
1. Enter privilege mode by typing enable at the console prompt.
2. The system will ask for the password.
3. Press the Enter key without providing a password. There is no password defined in
the default state.
The system will display a modified prompt:
4. The following command shows the switch is assigned an IP address of 192.168.10.10,
as an example.
By default, the management CPU and all the ports belong to VLAN 1. Thus, by
assigning the IP address to VLAN 1, the management CPU can be reached.
An alternative way to assign an IP address to the management VLAN (CPU) is to use
the ezconfig command. To use it, simply type ezconfig on the console command line.
User:admin
Password:
(FSM7352S) >enable
Password:
(FSM7352S) #
(FSM7352S) #conf
(FSM7352S) (Config)#interface vlan 1
(FSM7352S) (Interface-vlan 1)#ip address 192.168.10.1 255.255.255.0
(FSM7352S) (Interface-vlan 1)#
Log In to the Web Configuration Utility
1. Log in to the switch Web server by entering the IP address assigned in the last step
into a Web browser (http://192.168.1.0.1 in the example shown).
.A login window like the one shown below opens:
2. Click the Login link.
A user name and password dialog box opens like this one.
3. Type the default user name of admin and default of no password, or whatever
password you have set up. Then click the OK button.
Once you have logged in, your Web browser should automatically find the switch and
display the home page, similar to the illustration shown below.
Consult the full manual for your switch on the Resource CD for full configuration and
command line options.
Customer Support Information
Thank you for selecting NETGEAR products. Please register online and take advantage of
the technical support resources such as our online knowledge base. Point your browser to
http://www.NETGEAR.com/support/ and choose the product you are interested in to
browse for support information.
Register Your Product
To register, point your browser to this location:
http://www.NETGEAR.com/register