NEUTRIK NAC3FX-W-TOP User manual

800.638.6104 | www.covid.com
NAC3PX-TOP
NAC3MPX-TOP
NAC3MPX-WOT-TOP
NAC3FPX-TOP
NAC3FPX-WOT-TOP
NAC3FPX-ST-TOP
Power IN
Power OUT
Power OUT
NAC3FX-W-TOP
(Connector)
NAC3MX-W-TOP
(Plug connector)
-w
-w
20
250
P S
E
JET
-w
-w
20
250
P S
E
JET
20
250
P S
E
JET
16
250
20
250
NAC3MX-W
20
250
P S
E
JET
16
250
20
250
NAC3MX-W
NAC3FX-W-TOP
(Connector)
NAC3MX-W-TOP
(Plug connector)
Power IN
CONNECTOR ASSIGNMENT:
APPLIANCE INLET APPLIANCE OUTLET APPLIANCE INLET / OUTLET
Combination
40 - 50 mm
20
250
P S
E
JET
20
250
P S
E
JET
ASSEMBLY INSTRUCTION
NAC3FX-W-TOP power TRU 1CON E TOP
|
®
R
A. APPLICATION INSTRUCTION
B. ASSEMBLY INSTRUCTION
[0.32"]
8 mm
[ ”]0.787
2 mm0
[ ”]0.9
PE 23 mm
Separate the
housing from the
bushing (cable
remain in bushing)
B
Approval based:
Rating:
Cable Type:
Strain Relief:
Cable O.D.:
VDE
EN 60320-1/EN60320-2-2
250 V ac / 16 A
H05VV-F3G 1.0 mm , Length max. 2 m
2
H05VV-F3G 1.5 - 2.5 mm2
H07RN-F3G 1.5 mm2
White chuck
6.0 - 12.0 mm
UL
UL 498 / CSA C22.2 No. 182.3
250 V ac / 20 A
SJTOW, SJOOW 3 x 12 AWG
White chuck
6.0 - 12.0 mm
VDE (EN 60320-1/EN60320-2-2) UL (UL 498 / CSA C22.2 No. 182.3)
Place chuck over the
cable.
Prepare cable as
shown.
D
C
Page 1BDA 541
Application:
The power TRUE1 system is certified as connector with breaking cap ity accordingCON a ac
0625. an appliance coupler and interconnection coupler.IEC 60320, VDE It is intended for use as
anIt serves to supply power to appliance and from an appliance to other equipment.
To be installed by qualified person only.
Recommendation:
Wire Pulling Lubricant - LUB-I/0.95
from 3MTM
i
AInsert cable into the bushing and housing.
Note: “Apply cable pulling
lubricant to cable jacket.”
C
[0.32"]
8 mm
[ ”]0.787
2 mm0
[ ”]0.9
PE 23 mm
power TRUE1 TOP line is full backward compatible with the preceding power TRUE1 products.CON CON
UL50E environmental rating
Enclosure Type 4 when mated with attachment plug NAC3MX-W-TOP or mated with appliance inlet
NAC3MPX*-TOP with sealing cover SCNAC-MPX and NAC3PX-TOP with sealing cover SCNAC-PX.

800.638.6104 | www.covid.com
-w
-w
20
250
P S
E
JET
-w
-w
20
250
P S
E
JET
-w
-w
ASSEMBLY INSTRUCTION powerCON TRUE1 TOP
I
R
Page 2
G
Slide the cable into the contacts and clamp with
the screw with Torx size T8.
VDE ULWiring
blackLbrown

whiteNblue
green/yellow green
Slide intochuck onto insert (1) and then both
housing .(2)
Important: Align the chuck by positioning the
nose into keyway.
Slide the bushing up the cablecable clamp (3)
and with the tool (4) as shown (5).tighten it
Important: Black O-ring to hide to achieve IP
protection (6).
(Tool available: Art. No. HTAC)
2.
1.
-w
-w
Torque Value 0.7 Nm
Torx size
T8
5.
6.
E
F
www.neutrik.com
Find more details of power TRUE1 TOP on www.neutrik.com.CON
3.
Important:
Push and turn simultaneously.
Draft. Nr.: BDA 541 Update: .20111.07 8
II
Neutrik AG LI T: +423 / 237 24 24 F: [phone]/
Neutrik USA Inc. USA T: +1 704 / 972 3050 F: [phone]/
Neutrik () UK Ltd. UK T: +44 1983 / 811 441 F: [phone]/
Neutrik Vertriebs GmbH DE / NL / AT/DK T: +49 8131 / 280 890 F: [phone]/
Neutrik France FR T: [phone] F: [phone]//
Neutrik Tokyo Ltd. JP T: [phone] F: [phone]//
Neutrik Hong Kong Ltd. HK T: [phone] F: [phone]//
Neutrik India Pvt. Ltd. IND T: + F: [phone]/982 05 43 424 /
Data subject to change without prior notice. 201 NEUTRIK ALL RIGHTS RESERVED8 . NEUTRIK are registered trademark of NEUTRI AG. .©®®
LIECHTENSTEIN
20
250
P S
E
JET
CAUTION
To ensure protection
category, do not expose the
connection to bending forces
(e.g. do not attach loads to
the cable, no free-dangling
cable windings etc.).
FORCE
SAFETY WARNING
For safety and certification reasons the connector must be
replaced in case of any broken parts or .excessive wear and tear
2.
FOR DISASSEMBLY - OPEN TWIST LOCK!
1. Press with screw driver to unlock
Turn bushing 360°.2.
Repat step 1 + 2 until bushing is unscrewed.3.
1.
Torque Value 2.0 Nm
PRESS FIRMLY
4.
G
Wrench size
13 mm