NEUTRIK powerCON Product guide

OPERATING & ASSEMBLY INSTRUCTION
®
powerCON Locking 3 pole Power Connector
R
Page 1BDA 452
A. OPERATING INSTRUCTION
IMPORTANT SAFETY INSTRUCTION:
The powerCON system is certified as connector without breaking capacity according IEC 61984 / VDE 0627.
In this standard the term connector (without breaking capacity) refers to components which in normal use are not to
be engaged or disengaged when under load or live.
Connector Combination & Keyways:
With the two non-interchangeable types of connectors (A type and B type) it is impossible to produce a short circuit.
Mating connectors (combination) are identified by mechanical keyways and by color.
LIECHTENSTEIN
LIECHTENSTEIN
A type (color coding blue)
POWER IN
B type (color coding gray)
POWER OUT
B. ASSEMBLY INSTRUCTION
Place the bushing (1) and the chuck (2) over
the cable.
White chuck (a): 6.0 - 11.0 mm [0.236 - 0.433”]
Black chuck (b): 9.5 - 15.0 mm [0.374 - 0.59”]
VDE: 9.5 - 14.0 mm [0.374 - 0.551”]
Prepare the cable as shown.
Cable O.D.: 6.0 - 15.0 mm [0.236 - 0.59”]
2
Wire size: 2.5 mm (AWG 14)
Insert the wire into the terminals and fasten
the clamping device with a POZIDRIV® #1,
max. Torque 0.5 Nm (0.37 lb-ft).
B
A
B
[0.32"]
8 mm
[0.787”]
20 mm
[0.9”]
PE 23 mm
NAC3MPA-1
NAC3FCA
NAC3MPB-1
NAC3FCB
C
Torque Value 0.5 Nm
POZIDRIV® #1
NL
WIRING C
ð
or
1.
2.
b
a
A

ASSEMBLY INSTRUCTION Locking 3 pole powerCON
I
www.neutrik.com
NEUTRIK AG LI T: +423 / 237 24 24 F: +423 / 232 53 93
NEUTRIK USA Inc. USA T: +1 704 / 972 3050 F: +1 704 / 438 9202
( )
NEUTRIK UK Ltd. UK T: +44 1983 / 811 441 F: +44 1983 / 811 439
NEUTRIK Vertriebs GmbH DE / NL / AT/DK T: +49 8131 / 280 890 F: +49 8131 / 280 830
NEUTRIK France FR T: +33 1 / 4131 6750 F: +33 1 / 4131 0511
NEUTRIK Tokyo Ltd. JP T: +81 3 / 3663 4733 F: +81 3 / 3663 4796
NEUTRIK Hong Kong Ltd. HK T: +852 / 2687 6055 F: +852 / 2687 6052
NEUTRIK India Pvt. Ltd. IND T: +91 / 982 05 43 424 F: +91 / 22 26163
R
Draft. Nr.: BDA 452 Update: 31.08.2015 Data subject to change without prior notice. 2015 NEUTRIK . ALL RIGHTS RESERVED. NEUTRIK are registered trademark.
I I ® ®
©
Page 2
Slide the insert and the chuck (1) into the
housing (2).
Important:
Align the chuck by positioning the nose into (a)
the recess.
Pay attention to the guiding keyway!(b)
Fasten bushing by means of a fork wrench 7/8”
(SW 22), min. Torque 2.5 Nm (1.8 lb-ft).
D D
1.
a
2. b
E E
Torque Value 2.5 Nm
Wrench size
7/8" (SW22)
FINISHED powerCON
NAC3FCA NAC3FCB
Find more details of powerCON on www.neutrik.com.