Nexcom VTC 6210-R Series User manual

NEXCOM International Co., Ltd.
NEXCOM International Co., Ltd.
Published October 2015 www.nexcom.com
Mobile Computing Solutions
Vehicle Telematics Computer
VTC 6210-R Series
User Manual

Copyright © 2015 NEXCOM International Co., Ltd. All Rights Reserved. ii
Contents
VTC 6210-R Series User Manual
Contents
Preface
Copyright ............................................................................................. iv
Disclaimer ............................................................................................. iv
Acknowledgements .............................................................................. iv
Regulatory Compliance Statements ....................................................... iv
Declaration of Conformity...................................................................... iv
RoHS Compliance ................................................................................... v
Warranty and RMA ................................................................................ vi
Technical Support and Assistance........................................................... ix
Conventions Used in this Manual........................................................... ix
Global Service Contact Information......................................................... x
Package Contents..................................................................................xii
Chapter 1: Product Introduction
Physical Features .....................................................................................1
Front View...........................................................................................1
Rear View............................................................................................1
Overview ................................................................................................2
Key Features ...........................................................................................2
Hardware Specifications..........................................................................3
Connector Numbering ............................................................................5
Chapter 2: External Connectors Pinout Description
LED Indicators (HDD, WWAN, Power & WLAN) ....................................6
USB 3.0 Port........................................................................................6
Reset...................................................................................................7
SIM1 and SIM2 Sockets .......................................................................7
CFast...................................................................................................8
Line-out2.............................................................................................8
Mic2....................................................................................................9
Line-out1.............................................................................................9
Mic1..................................................................................................10
LAN1 and LAN2 Ports........................................................................10
USB 2.0 Port......................................................................................11
VGA..................................................................................................11
DisplayPort ........................................................................................12
GPIO/CAN .........................................................................................12
DC Input (24/36/110 VDC) ................................................................13
COM1 RS-232...................................................................................13
COM2 RS-232...................................................................................14
COM3 (RS422/485) ...........................................................................14
Chapter 3: Jumpers and Switches
Before You Begin .................................................................................15
Precautions ..........................................................................................15
Jumper Settings ....................................................................................16
DIP Switch Settings ...............................................................................18
RTC Clear Selection ...........................................................................18
GPIO Pull-High Setup.........................................................................18
MiniCard (CN26) Power Selection......................................................19

Copyright © 2015 NEXCOM International Co., Ltd. All Rights Reserved. iii
Contents
VTC 6210-R Series User Manual
WWAN Module Selection Table
(For Wake-Up & Voice Functions on Mini-PCIe CN26) ........................20
RTC Battery Connector......................................................................21
Debug 80 Port Connector .................................................................21
COM1/2 RS232 Connector................................................................22
COM3 RS232/422/485 Connector.....................................................22
Reset Button (Reserved).....................................................................23
Power Button Connector (Reserved) ..................................................23
SATA HDD Connector........................................................................24
Debug Port........................................................................................24
GAL Download Port...........................................................................25
GPS Connector..................................................................................25
Internal WWAN SIM Card Socket (SIM 3) For CN27 ...........................26
MCU Download Port .........................................................................26
Mini-PCIe (USB + PCIe) ......................................................................27
Mini-PCIe (USB) .................................................................................28
Mini-PCIe (USB) .................................................................................29
Chapter 4: System Setup
Removing the Chassis Cover ................................................................30
Installing a SSD/HDD Drive ....................................................................31
Installing a WLAN Module.....................................................................33
Installing a WWAN Module...................................................................33
Installing a SO-DIMM............................................................................34
Appendix A: Software Demo Utility for I/O Ports of
Function Control
Menu Screen .....................................................................................35
1.1 Status ........................................................................................36
1.2 GPIO Setting...............................................................................36
1.3 WDT Setting...............................................................................37
1.4 WWAN Module .........................................................................37
1.5 Selection of RS-422 or RS-485 for COM3 ...................................37
1.6 Power Off Delay Time ................................................................38
1.7 Wake Up Function .....................................................................38
1.8 CAN Bus Setting .......................................................................39
1.9 Interface Power ........................................................................39
1.10 Mini-PCIe Power .....................................................................40
Appendix B: GPS Feature
uBlox-NEO M8 Overview.......................................................................41
Technical Specifications.........................................................................41
Appendix C: Signal Connection of DI/DO
GPIO Pinout Description........................................................................43
SW2 Setting..........................................................................................43
Digital Input..........................................................................................44
Digital Output.......................................................................................45
Appendix D: Vehicle Power Management Setup
Power-on Delay Setting.........................................................................46
Power-off Delay Setting ........................................................................48
Appendix E: Power Consumption..........................50

Copyright © 2015 NEXCOM International Co., Ltd. All Rights Reserved. iv
Preface
VTC 6210-R Series User Manual
Regulatory Compliance Statements
This section provides the FCC compliance statement for Class B devices and
describes how to keep the system CE compliant.
Declaration of Conformity
FCC
This equipment has been tested and verified to comply with the limits for
a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference
to radio communications. Operation of this equipment in a residential area
(domestic environment) is likely to cause harmful interference, in which
case the user will be required to correct the interference (take adequate
measures) at their own expense.
CE
The product(s) described in this manual complies with all applicable
European Union (CE) directives if it has a CE marking. For computer systems
to remain CE compliant, only CE-compliant parts may be used. Maintaining
CE compliance also requires proper cable and cabling techniques.
Copyright
This publication, including all photographs, illustrations and software, is
protected under international copyright laws, with all rights reserved. No
part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written consent from
NEXCOM International Co., Ltd.
Disclaimer
The information in this document is subject to change without prior notice
and does not represent commitment from NEXCOM International Co., Ltd.
However, users may update their knowledge of any product in use by constantly
checking its manual posted on our website: http://www.nexcom.com. NEXCOM
shall not be liable for direct, indirect, special, incidental, or consequential
damages arising out of the use of any product, nor for any infringements
upon the rights of third parties, which may result from such use. Any implied
warranties of merchantability or fitness for any particular purpose is also
disclaimed.
Acknowledgements
VTC 6210-R Series is a trademark of NEXCOM International Co., Ltd. All
other product names mentioned herein are registered trademarks of their
respective owners.
PrefaCe

Copyright © 2015 NEXCOM International Co., Ltd. All Rights Reserved. v
Preface
VTC 6210-R Series User Manual
RoHS Compliance
NEXCOM RoHS Environmental Policy and Status
Update
NEXCOM is a global citizen for building the digital
infrastructure. We are committed to providing green
products and services, which are compliant with
European Union RoHS (Restriction on Use of Hazardous Substance in
Electronic Equipment) directive 2011/65/EU, to be your trusted green
partner and to protect our environment.
RoHS restricts the use of Lead (Pb) < 0.1% or 1,000ppm, Mercury (Hg)
< 0.1% or 1,000ppm, Cadmium (Cd) < 0.01% or 100ppm, Hexavalent
Chromium (Cr6+) < 0.1% or 1,000ppm, Polybrominated biphenyls (PBB) <
0.1% or 1,000ppm, and Polybrominated diphenyl Ethers (PBDE) < 0.1% or
1,000ppm.
In order to meet the RoHS compliant directives, NEXCOM has established an
engineering and manufacturing task force in to implement the introduction
of green products. The task force will ensure that we follow the standard
NEXCOM development procedure and that all the new RoHS components
and new manufacturing processes maintain the highest industry quality
levels for which NEXCOM are renowned.
How to recognize NEXCOM RoHS Products?
For existing products where there are non-RoHS and RoHS versions, the
suffix “(LF)” will be added to the compliant product name.
All new product models launched after January 2013 will be RoHS compliant.
They will use the usual NEXCOM naming convention.

Copyright © 2015 NEXCOM International Co., Ltd. All Rights Reserved. vi
Preface
VTC 6210-R Series User Manual
Warranty and RMA
NEXCOM Warranty Period
NEXCOM manufactures products that are new or equivalent to new in
accordance with industry standard. NEXCOM warrants that products will
be free from defect in material and workmanship for 2 years, beginning on
the date of invoice by NEXCOM. HCP series products (Blade Server) which
are manufactured by NEXCOM are covered by a three year warranty period.
NEXCOM Return Merchandise Authorization (RMA)
▪Customers shall enclose the “NEXCOM RMA Service Form” with the
returned packages.
▪Customers must collect all the information about the problems
encountered and note anything abnormal or, print out any on-screen
messages, and describe the problems on the “NEXCOM RMA Service
Form” for the RMA number apply process.
▪Customers can send back the faulty products with or without accessories
(manuals, cable, etc.) and any components from the card, such as CPU
and RAM. If the components were suspected as part of the problems,
please note clearly which components are included. Otherwise, NEXCOM
is not responsible for the devices/parts.
▪Customers are responsible for the safe packaging of defective products,
making sure it is durable enough to be resistant against further damage
and deterioration during transportation. In case of damages occurred
during transportation, the repair is treated as “Out of Warranty.”
▪Any products returned by NEXCOM to other locations besides the
customers’ site will bear an extra charge and will be billed to the customer.
Repair Service Charges for Out-of-Warranty Products
NEXCOM will charge for out-of-warranty products in two categories, one is
basic diagnostic fee and another is component (product) fee.
System Level
▪Component fee: NEXCOM will only charge for main components such as
SMD chip, BGA chip, etc. Passive components will be repaired for free,
ex: resistor, capacitor.
▪Items will be replaced with NEXCOM products if the original one cannot
be repaired. Ex: motherboard, power supply, etc.
▪Replace with 3rd party products if needed.
▪If RMA goods can not be repaired, NEXCOM will return it to the customer
without any charge.
Board Level
▪Component fee: NEXCOM will only charge for main components, such
as SMD chip, BGA chip, etc. Passive components will be repaired for free,
ex: resistors, capacitors.
▪If RMA goods can not be repaired, NEXCOM will return it to the customer
without any charge.

Copyright © 2015 NEXCOM International Co., Ltd. All Rights Reserved. vii
Preface
VTC 6210-R Series User Manual
Warnings
Read and adhere to all warnings, cautions, and notices in this guide and
the documentation supplied with the chassis, power supply, and accessory
modules. If the instructions for the chassis and power supply are inconsistent
with these instructions or the instructions for accessory modules, contact
the supplier to find out how you can ensure that your computer meets
safety and regulatory requirements.
Cautions
Electrostatic discharge (ESD) can damage system components. Do the
described procedures only at an ESD workstation. If no such station is
available, you can provide some ESD protection by wearing an antistatic
wrist strap and attaching it to a metal part of the computer chassis.
Safety Information
Before installing and using the device, note the following precautions:
▪Read all instructions carefully.
▪Do not place the unit on an unstable surface, cart, or stand.
▪Follow all warnings and cautions in this manual.
▪When replacing parts, ensure that your service technician uses parts
specified by the manufacturer.
▪Avoid using the system near water, in direct sunlight, or near a heating
device.
▪The load of the system unit does not solely rely for support from the
rackmounts located on the sides. Firm support from the bottom is highly
necessary in order to provide balance stability.
▪The computer is provided with a battery-powered real-time clock circuit.
There is a danger of explosion if battery is incorrectly replaced. Replace
only with the same or equivalent type recommended by the manufacturer.
Discard used batteries according to the manufacturer’s instructions.
Installation Recommendations
Ensure you have a stable, clean working environment. Dust and dirt can
get into components and cause a malfunction. Use containers to keep
small components separated.
Adequate lighting and proper tools can prevent you from accidentally
damaging the internal components. Most of the procedures that follow
require only a few simple tools, including the following:
• A Philips screwdriver
• A flat-tipped screwdriver
• A grounding strap
• An anti-static pad
Using your fingers can disconnect most of the connections. It is recom-
mended that you do not use needlenose pliers to disconnect connections
as these can damage the soft metal or plastic parts of the connectors.

Copyright © 2015 NEXCOM International Co., Ltd. All Rights Reserved. viii
Preface
VTC 6210-R Series User Manual
Safety Precautions
▪Read these safety instructions carefully.
▪Keep this User Manual for later reference.
▪Disconnect this equipment from any AC outlet before cleaning. Use a
damp cloth. Do not use liquid or spray detergents for cleaning.
▪For plug-in equipment, the power outlet socket must be located near the
equipment and must be easily accessible.
▪Keep this equipment away from humidity.
▪Put this equipment on a stable surface during installation. Dropping it or
letting it fall may cause damage.
▪Do not leave this equipment in either an unconditioned environment or
in a above 40oC storage temperature as this may damage the equipment.
▪The openings on the enclosure are for air convection to protect the
equipment from overheating. DO NOT COVER THE OPENINGS.
▪Make sure the voltage of the power source is correct before connecting
the equipment to the power outlet.
▪Place the power cord in a way so that people will not step on it. Do not
place anything on top of the power cord. Use a power cord that has been
approved for use with the product and that it matches the voltage and
current marked on the product’s electrical range label. The voltage and
current rating of the cord must be greater than the voltage and current
rating marked on the product.
▪All cautions and warnings on the equipment should be noted.
▪If the equipment is not used for a long time, disconnect it from the power
source to avoid damage by transient overvoltage.
▪Never pour any liquid into an opening. This may cause fire or electrical
shock.
▪Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
▪If one of the following situations arises, get the equipment checked by
service personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work
according to the user’s manual.
e. The equipment has been dropped and damaged.
f. The equipment has obvious signs of breakage.
▪Do not place heavy objects on the equipment.
▪The unit uses a three-wire ground cable which is equipped with a third
pin to ground the unit and prevent electric shock. Do not defeat the
purpose of this pin. If your outlet does not support this kind of plug,
contact your electrician to replace your obsolete outlet.
▪CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE
RECOMMENDED BY THE MANUFACTURER. DISCARD USED BATTERIES
ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS.
▪The computer is provided with CD drives that comply with the appropriate
safety standards including IEC 60825.

Copyright © 2015 NEXCOM International Co., Ltd. All Rights Reserved. ix
Preface
VTC 6210-R Series User Manual
Conventions Used in this Manual
Warning:
Information about certain situations, which if not observed,
can cause personal injury. This will prevent injury to yourself
when performing a task.
CAUTION!
CAUTION!CAUTION! Caution:
Information to avoid damaging components or losing data.
Note:
Provides additional information to complete a task easily.
Technical Support and Assistance
1. For the most updated information of NEXCOM products, visit NEXCOM’s
website at www.nexcom.com.
2. For technical issues that require contacting our technical support team or
sales representative, please have the following information ready before
calling:
– Product name and serial number
– Detailed information of the peripheral devices
– Detailed information of the installed software (operating system,
version, application software, etc.)
– A complete description of the problem
– The exact wordings of the error messages
Warning!
1. Handling the unit: carry the unit with both hands and handle it with care.
2. Maintenance: to keep the unit clean, use only approved cleaning products
or clean with a dry cloth.
3. CompactFlash: Turn off the unit’s power before inserting or removing a
CompactFlash storage card.

Copyright © 2015 NEXCOM International Co., Ltd. All Rights Reserved. x
Preface
VTC 6210-R Series User Manual
Global Service Contact Information
Headquarters
NEXCOM International Co., Ltd.
15F, No. 920, Chung-Cheng Rd.,
ZhongHe District, New Taipei City, 23586,
Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
www.nexcom.com
America
USA
NEXCOM USA
2883 Bayview Drive,
Fremont CA 94538, USA
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.com
Asia
Taiwan
NEXCOM Intelligent Systems
Taipei Office
13F, No.920, Chung-Cheng Rd.,
ZhongHe District,
New Taipei City, 23586, Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.com.tw
NEXCOM Intelligent Systems
Taichung Office
16F, No.250, Sec. 2, Chongde Rd.,
Beitun Dist.,
Taichung City 406, R.O.C.
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.com.tw
Japan
NEXCOM Japan
9F, Tamachi Hara Bldg.,
4-11-5, Shiba Minato-ku,
Tokyo, 108-0014, Japan
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom-jp.com
China
NEXCOM China
1F & 2F, Block A, No. 16 Yonyou Software Park,
No. 68 Beiqing Road, Haidian District,
Beijing, 100094, China
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.cn

Copyright © 2015 NEXCOM International Co., Ltd. All Rights Reserved. xi
Preface
VTC 6210-R Series User Manual
Chengdu Office
9F, Shuxiangxie, Xuefu Garden,
No.12 Section 1, South Yihuan Rd.,
Chengdu, 610061, China
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.cn
Shenzhen Office
Room1707, North Block, Pines Bldg.,
No.7 Tairan Rd., Futian Area,
Shenzhen, 518040, China
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.cn
Wuhan Office
1-C1804/1805, Mingze Liwan, No. 519
South Luoshi Rd., Hongshan District,
Wuhan, 430070, China
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.cn
Europe
United Kingdom
NEXCOM EUROPE
10 Vincent Avenue,
Crownhill Business Centre,
Milton Keynes, Buckinghamshire
MK8 0AB, United Kingdom
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.eu
Italy
NEXCOM ITALIA S.r.l
Via Lanino 42,
21047 Saronno (VA), Italia
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcomitalia.it
NEXCOM Shanghai
Room 603/604, Huiyinmingzun Plaza Bldg., 1,
No.609, Yunlin East Rd.,
Shanghai, 200333, China
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.cn
NEXCOM Surveillance Technology
Room202, Building B, the GuangMing
Industrial Zone Zhonghua Rd.,
Minzhi Street, Longhua District,
Shenzhen, China
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.cn
NEXCOM United System Service
Hui Yin Ming Zun Building Room 1108,
Building 11, 599 Yunling Road, Putuo District,
Shanghai, 200062, China
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.cn

Copyright © 2015 NEXCOM International Co., Ltd. All Rights Reserved. xii
Preface
VTC 6210-R Series User Manual
Package Contents
Before continuing, verify that the VTC 6210-R Series package that you received is complete. Your VTC 6210-R Series package should have all the items listed
in the following table.
Item P/N Name Specification Qty
1 60233SAM05X00 GPS Antenna ARKNAV:A-130 5M SMA180P R1 L3 1
2 4NCPM01601X00 Terminal Blocks 2x8 ANYTEK:KD161051A000G 3.5mm Male 16P 180D Plug Green 1
3 602DCD1064X00 VTC 6210-R Series DVD Driver VER:1.0 JCL 1
4 5060300058X00 (N)VTC 6210-RA HDD Mylar S.W. Mylar Black 1
5 5061500056X00 (N)VTC 6210-RA Hole Plugs Kang Yang 6x6mm EPDM Black 4
6 4NCPF00314X00 IP67 Power Connector 3-pin ST:ST-031 20A Female Screw Diameter:22.2x48.15mm 1
7 603LAN0011X00 LAN Cable for nROK5500-F ST:LTW12-08BMMA-SL8001 LTW Waterproof 8P 3
8 50333P0027X00 Washer for SMA Connector Kang Yang:TW-181 13x1.8mm Nylon 66 Natural 4
9 50333P0028X00 Washer for SMA Connector Kang Yang:WS6-0.8(B) 12.8x6.4x0.8mm PC Black 4

Copyright © 2015 NEXCOM International Co., Ltd. All Rights Reserved. xiii
Preface
VTC 6210-R Series User Manual
Ordering Information
The following provides ordering information for the VTC 6210-R Series.
▪VTC 6210-RA (P/N: 10V00621003X0)
Intel®Atom™ processor E3845 1.91GHz CPU, 2GB DDR3L SO-DIMM,
VGA/DP output, 2x M12 Giga LAN, 2x RS-232 (isolation), 1x RS 422/485
(isolation), 8x GPIO (isolation), 1x M12 (two USB 2.0), 1x USB 3.0 Type A,
24/36VDC Input w/o isolation
▪VTC 6210-RF (P/N: 10V00621005X0)
Intel®Atom™ processor E3845 1.91GHz CPU, 2GB DDR3L SO-DIMM,
VGA/DP output, 2x M12 Giga LAN, 2x RS-232 (isolation), 1x RS 422/485
(isolation), 8x GPIO (isolation), 1x M12 (two USB 2.0), 1x USB 3.0 Type A,
110VDC Input w/ isolation

Copyright © 2015 NEXCOM International Co., Ltd. All Rights Reserved. 1
Chapter 1: Product Introduction
VTC 6210-R Series User Manual
ChaPter 1: ProduCt IntroduCtIon
Physical Features
Front View
SSD/HDD
CFast Line-out 2
Mic2
SIM1 / SIM2
slot cover
LED
indicators
USB 3.0
Reset
Antenna holes GPS
Mic1
COM1 COM2 COM3LAN1Line-out 1
VGA GPIO/CAN
DisplayPort
DC IN
LAN2
USB
Rear View

Copyright © 2015 NEXCOM International Co., Ltd. All Rights Reserved. 2
Chapter 1: Product Introduction
VTC 6210-R Series User Manual
Overview
VTC 6210-R Series, based on Intel®Core™ quad core processor E3845
(1.91GHz), is specifically designed for rolling stock environments. It allows
VTC 6210-R Series to comply with the EN50155 standard in rugged, fanless
and compact mechanism. VTC 6210-R Series features rich PAN, WLAN and
WWAN wireless connectivity. With three SIM cards support, VTC 6210-R
Series allows three SIM cards backup each other for a better connectivity
quality by software. In addition, three SIM cards and dual WWAN modules
architecture can increase the bandwidth for a faster data transmission speed.
Not only data transmission, VTC 6210-R Series also supports two-way voice
communication. Equipped with intelligent power management, VTC 6210-
R Series can be waked on by ignition, RTC timer or SMS message remotely.
By integrating the variety of I/O ports and 3x Mini-PCIe sockets expansibility,
VTC 6210-R Series keeps the flexibility to meet the demand for different
rolling stock applications, such as infotainment and video surveillance.
Key Features
• Intel®Atom™ processor quad core E3845, 1.91GHz
• Three SIM cards + dual WWAN modules support
• Built-in U-blox NEO M8N GPS, optional 5V Antenna or Dead Reckoning
support
• Built-in CAN Bus 2.0B
• Wake on RTC/SMS via WWAN module
• Compliant with MIL-STD-810G
• 3x Mini-PCIe socket expansion
• 8x GPIO w/ isolation
• 3x COM Port w/ isolation
• Voice communication via WWAN module
• EN50155 Certification

Copyright © 2015 NEXCOM International Co., Ltd. All Rights Reserved. 3
Chapter 1: Product Introduction
VTC 6210-R Series User Manual
Hardware Specifications
CPU
▪Intel®Atom™ processor quad core E3845, 1.91GHz
Memory
▪1x 204-pin DDR3L SO-DIMM socket support 1066MHz/1333MHz up to 8GB.
Default 2GB
Storage
▪1x 2.5” SSD/HDD SATA 2.0
(externally accessible, optional lockable storage available)
▪1x CFast (externally accessible)
Expansion
▪1x full size Mini-PCIe socket (USB 2.0)
▪1x full size Mini-PCIe socket (USB 2.0 + PCIe)
▪1x full size Mini-PCIe socket (USB 2.0 + PCIe)
Function
▪1x default uBlox-M8L GPS module (72-channel, GALILEO & GLONASS),
optional with 5V Antenna of Dead Reckoning support
▪Built-in G-sensor
I/O Interface-Front
▪4x LED for power, storage, WWAN, WLAN
▪2x externally accessible SIM card socket (selectable)
▪1x phone jack 3.5mm for 1x Mic-In (optional waterproof connector)
▪1x phone jack 3.5mm for 1x Line-Out (optional waterproof connector)
▪1x externally accessible 2.5” SATA 2.0 SSD/HDD tray
▪1x externally accessible CFast card socket with cover
▪1x reset button
▪1x type A USB 3.0 compliant host, supporting system boot up
▪4x antenna hole for WWAN/WLAN/BT
I/O Interface-Rear
▪1x Waterproof DC Input with ignition and 19W typical power consumption
(optional 24/36/110 VDC)
▪1x M12 w/ two USB 2.0 compliant host, supporting system boot up
▪2x M12 10/100/1000 Fast Ethernet
▪1x phone jack 3.5mm for 1x Mic-In (optional waterproof connector)
▪1x phone jack 3.5mm for 1x Line-Out (optional waterproof connector)
▪1x DB-15 VGA, resolution up to 2560 x 1600 @60Hz
▪1x DP port, resolution up to 2560 x 1600 @60H
▪1x antenna hole for GPS
▪2x DB-9 RS-232 (isolation)
▪1x DB-9 RS-422/485 (isolation)
▪1x 16-pin terminal block
- 1x CAN Bus 2.0B (on board)
- 4x GPI + 4x GPO (isolation)
Digital Input (internal type): 5VDC TTL (default)
Digital Input (source type): 3~12VDC
Digital Output (sink type): 5VDC TTL (default), max current: 20mA
Digital Output (source type): 3~19VDC, max current: 150mA
Power Management
▪Selectable boot-up & shut-down voltage for low power protection by
software
▪Setting 8-level power on/off delay time by software
▪Status of ignition and low voltage can be detected by software
▪Support S3/S4 suspend mode
Operating System
▪Windows 8, WES8
▪Windows 7, WES8
▪Fedora

Copyright © 2015 NEXCOM International Co., Ltd. All Rights Reserved. 4
Chapter 1: Product Introduction
VTC 6210-R Series User Manual
Dimensions
▪260 mm (W) x 176 mm (D) x 70 mm (H) (10.24” x 6.93” x 2.75”)
▪Weight : 2.1kg
Environment
▪Operating temperatures: -40°C to 70°C (w/industrial SSD) with air flow
-10°C to 50°C (w/commercial HDD) with air flow
▪Storage temperatures: -40°C to 85°C
▪Relative humidity: 10% to 90% (non-condensing)
Certifications
▪CE approval
▪FCC Class A
▪EN50155 Certification
- Ambient Temperature EN 50155 TX (-40 ~ 70°C)
- Shock and Vibration IEC 61373 class B
- Interruptions of Voltage Supply Class S1, S2
- Supply Change Over Class C1, C2
- EMC EN 50121-3-2

Copyright © 2015 NEXCOM International Co., Ltd. All Rights Reserved. 5
Chapter 1: Product Introduction
VTC 6210-R Series User Manual
Connector Numbering
The following diagrams indicate the numbers of the connectors. Use these
numbers to locate the connectors’ respective pinout assignments on chapter
2 of the manual.
     

Copyright © 2015 NEXCOM International Co., Ltd. All Rights Reserved. 6
Chapter 2: External Connectors Pinout Description
VTC 6210-R Series User Manual
ChaPter 2: external ConneCtors PInout desCrIPtIon
LED Indicators (HDD, WWAN, Power & WLAN)
Connector Number: 1
LED LED Behavior
HDD Light On: HDD/SSD Active
PWR Light On: Power On
Light Off: Power Off
WWAN Blinking: Active
WLAN Blinking: Active
HDD
PWR
WWAN
WLAN
USB 3.0 Port
Connector Number: 2
Pin Definition Pin Definition
1 5V 2 USB_N
3 USB_P 4 GND
5 USB3_RXN 6 USB3_RXP
7 GND 8 USB3_TXN
9 USB3_TXP
41
95

Copyright © 2015 NEXCOM International Co., Ltd. All Rights Reserved. 7
Chapter 2: External Connectors Pinout Description
VTC 6210-R Series User Manual
Reset
Connector Number: 3
Pin Definition
1 GND
2 RESET
1 2
SIM1 and SIM2 Sockets
Connector Number: 4
Pin Definition Pin Definition
C1 UIM1_PWR2 C5 GND
C2 UIM1_RST2 C6 NC
C3 UIM1_CLK2 C7 UIM1_DAT2
C3
C2
C1
C7
C6
C5