Nexcom VTC 7200-BK User manual

NEXCOM International Co., Ltd.
NEXCOM International Co., Ltd.
Published March 2017 www.nexcom.com
Mobile Computing Solutions
Vehicle Telematics Computer
VTC 7200-BK/7210-BK/7220-BK/7230-BK/7240-BK
User Manual

Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. ii
Contents
VTC 7200-BK Series User Manual
Contents
Preface
Copyright .............................................................................................. v
Disclaimer .............................................................................................. v
Acknowledgements ............................................................................... v
Regulatory Compliance Statements ........................................................ v
Declaration of Conformity....................................................................... v
RoHS Compliance .................................................................................. vi
Warranty and RMA ................................................................................vii
Technical Support and Assistance............................................................ x
Conventions Used in this Manual............................................................ x
Global Service Contact Information........................................................ xi
Package Contents.................................................................................xiii
Ordering Information ............................................................................xiv
Chapter 1: Product Introduction
Physical Features .....................................................................................1
Front View...........................................................................................1
Rear View............................................................................................1
Overview ................................................................................................2
Key Features ...........................................................................................2
Hardware Specifications..........................................................................3
Connector Numbering ............................................................................5
Chapter 2: External Connectors Pinout Description
Event Button .......................................................................................6
LED Indicators (HDD, WWAN, Power & WLAN) ....................................6
Reset...................................................................................................7
SIM1 and SIM2 Sockets For CN23 and CN21.......................................7
USB 3.0 and USB 2.0 Ports (Front) .......................................................8
CFast...................................................................................................8
Line-out2.............................................................................................9
Mic2....................................................................................................9
LAN2 Port..........................................................................................10
LAN1 Port..........................................................................................10
Mic1..................................................................................................11
Line-out1...........................................................................................11
USB 3.0 and USB 2.0 Ports (Rear).......................................................12
DisplayPort ........................................................................................12
VGA..................................................................................................13
GPIO/CAN/OBDII................................................................................13
DC Output ........................................................................................14
DC Input 9V-36V...............................................................................14
COM1 and COM3.............................................................................15
COM2 (RS232/422/485 and RI/12V Selection)....................................15
MCU-DIO ..........................................................................................16
Chapter 3: Jumpers and Switches
Before You Begin .................................................................................17
Precautions ..........................................................................................17
Jumper Settings ....................................................................................18
DIP Switch Settings ...............................................................................20
GPIO Pull High Switch........................................................................20

Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. iii
Contents
VTC 7200-BK Series User Manual
COM2 RI/12V Selection .....................................................................20
VCC Selection Switch for CN23 Mini-PCIe Socket .............................21
WWAN Module Selector
(For Wake-Up & Voice Functions on Mini-PCIe CN23) ........................22
ME/RTC Clear Switch.........................................................................22
Input Voltage Control Switch.............................................................23
Power SW Connector ........................................................................24
GLA Flash Connector ........................................................................24
MCU Debug COM Connector............................................................25
MCU Flash Connector .......................................................................25
MCU Temp Sensor.............................................................................26
LVDS BL Control Connector ..............................................................26
LVDS Connector ................................................................................27
SATA Power Connectors ....................................................................27
SATA Connectors...............................................................................28
GPS Connector..................................................................................28
Expansion Connector (For VIOB-mPCI expansion card).......................29
COM1/3 RS232 Connector................................................................29
COM2 RS232/422/485 Connector.....................................................30
Super I/O Temperature Sensor............................................................30
RTC Battery Connector......................................................................31
Debug 80 Port Connector..................................................................31
Optional VIOB-CAN03 Module Connector.........................................32
Power Connector for CAN 2.0B MiniCard (MPX-2515) ......................32
3G GPS RF Connector........................................................................33
BT Connector ....................................................................................33
Mini-PCIe (PCIe + USB) ......................................................................34
Mini-PCIe (PCIe + USB) ......................................................................35
Mini-PCIe (PCIe + USB) ......................................................................36
Internal WWAN SIM Card Socket (SIM 3) For CN21 ...........................37
Mini-PCIe (USB) .................................................................................38
Optional Internal WWAN SIM1 Card Socket For CN23.......................39
Optional Internal WWAN SIM2 Card Socket For CN21 or CN23 ........39
Chapter 4: System Setup
Removing the Chassis Bottom Cover ....................................................40
Installing a SSD/HDD Drive ....................................................................41
Installing a WLAN Module (Half Mini-PCIe)............................................46
Installing the First WWAN Module.........................................................46
Installing the Second WWAN Module....................................................47
Installing a SO-DIMM............................................................................48
Installing a OBDII Module......................................................................49
Appendix A: Software Demo Utility for I/O Ports of
Function Control
Menu Screen .....................................................................................50
1.1 Status ........................................................................................51
1.2 Input Voltage..............................................................................51
1.3 Output Power.............................................................................52
1.4 GPIO Setting...............................................................................52
1.5 MCU GPIO Setting......................................................................53
1.6 WDT Setting...............................................................................53
1.7 WWAN Module .........................................................................54
1.8 Power On Delay Time ................................................................54
1.9 Power Off Delay Time ................................................................54
1.10 Wake Up Function ...................................................................55
1.11 CAN Bus Setting .....................................................................55
1.12 Interface Power ......................................................................56
1.13 Mini-PCIe Power .....................................................................56
Appendix B: GPS Feature
uBlox-NEO M8 Overview.......................................................................57
Technical Specifications.........................................................................57
Appendix C: Signal Connection of DI/DO
GPIO Pinout Description........................................................................59
SW1 Setting..........................................................................................59

Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. iv
Contents
VTC 7200-BK Series User Manual
Digital Input..........................................................................................60
Digital Output.......................................................................................61
Appendix D: Signal Connection of MCU DI/DO and
Event Button
MCU-DIO Pinout Description.................................................................62
Digital Input..........................................................................................62
Digital Output.......................................................................................63
Event Button.........................................................................................63
Pre-Alarm Function by Event Button, MCU-DI and MCU-DO .................65
Setting up Pre-Alarm function ...........................................................65
Activating Pre-Alarm function............................................................66
Deactivating Pre-Alarm function ........................................................66
Activating Pre-Alarm Function ..............................................................67
(For Event Button)..............................................................................67
(For MCU-DI2)...................................................................................67
Deactivating Pre-Alarm Function ..........................................................68
(For Event Button)..............................................................................68
(For MCU-DI2)...................................................................................68
Appendix E: Vehicle Power Management Setup
External Power Output Setting..............................................................69
Startup and Shutdown Voltage Setting .................................................69
Power-on Delay Setting.........................................................................71
Power-off Delay Setting ........................................................................73
Appendix F: OBDII Module Setup and Command
OBDII Module .......................................................................................75
VIOX-CAN01 Setup...............................................................................75
AT Command Summary........................................................................76
Simple Data Protocol: (ASCII CODE) ......................................................77
Simple Data Protocol: (HEX CODE)........................................................78
J1939 Raw Data Protocol (HEX CODE) ..................................................79
J1708 Raw Data Protocol (HEX CODE) ..................................................79
J1939 Packaged Messages Protocol ......................................................80
J1708 Packaged Messages Protocol ......................................................88
J1708 Command Example ....................................................................92
Appendix G: Power Consumption ........................93

Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. v
Preface
VTC 7200-BK Series User Manual
Regulatory Compliance Statements
This section provides the FCC compliance statement for Class B devices and
describes how to keep the system CE compliant.
Declaration of Conformity
FCC
This equipment has been tested and verified to comply with the limits for
a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference
to radio communications. Operation of this equipment in a residential area
(domestic environment) is likely to cause harmful interference, in which
case the user will be required to correct the interference (take adequate
measures) at their own expense.
CE
The product(s) described in this manual complies with all applicable
European Union (CE) directives if it has a CE marking. For computer systems
to remain CE compliant, only CE-compliant parts may be used. Maintaining
CE compliance also requires proper cable and cabling techniques.
Copyright
This publication, including all photographs, illustrations and software, is
protected under international copyright laws, with all rights reserved. No
part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written consent from
NEXCOM International Co., Ltd.
Disclaimer
The information in this document is subject to change without prior notice
and does not represent commitment from NEXCOM International Co., Ltd.
However, users may update their knowledge of any product in use by constantly
checking its manual posted on our website: http://www.nexcom.com. NEXCOM
shall not be liable for direct, indirect, special, incidental, or consequential
damages arising out of the use of any product, nor for any infringements
upon the rights of third parties, which may result from such use. Any implied
warranties of merchantability or fitness for any particular purpose is also
disclaimed.
Acknowledgements
VTC 7200-BK, VTC 7210-BK, VTC 7220-BK, VTC 7230-BK and VTC 7240-BK
are trademarks of NEXCOM International Co., Ltd. All other product names
mentioned herein are registered trademarks of their respective owners.
Preface

Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. vi
Preface
VTC 7200-BK Series User Manual
RoHS Compliance
NEXCOM RoHS Environmental Policy and Status
Update
NEXCOM is a global citizen for building the digital
infrastructure. We are committed to providing green
products and services, which are compliant with
European Union RoHS (Restriction on Use of Hazardous Substance in
Electronic Equipment) directive 2011/65/EU, to be your trusted green
partner and to protect our environment.
RoHS restricts the use of Lead (Pb) < 0.1% or 1,000ppm, Mercury (Hg)
< 0.1% or 1,000ppm, Cadmium (Cd) < 0.01% or 100ppm, Hexavalent
Chromium (Cr6+) < 0.1% or 1,000ppm, Polybrominated biphenyls (PBB) <
0.1% or 1,000ppm, and Polybrominated diphenyl Ethers (PBDE) < 0.1% or
1,000ppm.
In order to meet the RoHS compliant directives, NEXCOM has established an
engineering and manufacturing task force in to implement the introduction
of green products. The task force will ensure that we follow the standard
NEXCOM development procedure and that all the new RoHS components
and new manufacturing processes maintain the highest industry quality
levels for which NEXCOM are renowned.
How to recognize NEXCOM RoHS Products?
For existing products where there are non-RoHS and RoHS versions, the
suffix “(LF)” will be added to the compliant product name.
All new product models launched after January 2013 will be RoHS compliant.
They will use the usual NEXCOM naming convention.

Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. vii
Preface
VTC 7200-BK Series User Manual
Warranty and RMA
NEXCOM Warranty Period
NEXCOM manufactures products that are new or equivalent to new in
accordance with industry standard. NEXCOM warrants that products will
be free from defect in material and workmanship for 2 years, beginning on
the date of invoice by NEXCOM. HCP series products (Blade Server) which
are manufactured by NEXCOM are covered by a three year warranty period.
NEXCOM Return Merchandise Authorization (RMA)
▪Customers shall enclose the “NEXCOM RMA Service Form” with the
returned packages.
▪Customers must collect all the information about the problems
encountered and note anything abnormal or, print out any on-screen
messages, and describe the problems on the “NEXCOM RMA Service
Form” for the RMA number apply process.
▪Customers can send back the faulty products with or without accessories
(manuals, cable, etc.) and any components from the card, such as CPU
and RAM. If the components were suspected as part of the problems,
please note clearly which components are included. Otherwise, NEXCOM
is not responsible for the devices/parts.
▪Customers are responsible for the safe packaging of defective products,
making sure it is durable enough to be resistant against further damage
and deterioration during transportation. In case of damages occurred
during transportation, the repair is treated as “Out of Warranty.”
▪Any products returned by NEXCOM to other locations besides the
customers’ site will bear an extra charge and will be billed to the customer.
Repair Service Charges for Out-of-Warranty Products
NEXCOM will charge for out-of-warranty products in two categories, one is
basic diagnostic fee and another is component (product) fee.
System Level
▪Component fee: NEXCOM will only charge for main components such as
SMD chip, BGA chip, etc. Passive components will be repaired for free,
ex: resistor, capacitor.
▪Items will be replaced with NEXCOM products if the original one cannot
be repaired. Ex: motherboard, power supply, etc.
▪Replace with 3rd party products if needed.
▪If RMA goods can not be repaired, NEXCOM will return it to the customer
without any charge.
Board Level
▪Component fee: NEXCOM will only charge for main components, such
as SMD chip, BGA chip, etc. Passive components will be repaired for free,
ex: resistors, capacitors.
▪If RMA goods can not be repaired, NEXCOM will return it to the customer
without any charge.

Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. viii
Preface
VTC 7200-BK Series User Manual
Warnings
Read and adhere to all warnings, cautions, and notices in this guide and
the documentation supplied with the chassis, power supply, and accessory
modules. If the instructions for the chassis and power supply are inconsistent
with these instructions or the instructions for accessory modules, contact
the supplier to find out how you can ensure that your computer meets
safety and regulatory requirements.
Cautions
Electrostatic discharge (ESD) can damage system components. Do the
described procedures only at an ESD workstation. If no such station is
available, you can provide some ESD protection by wearing an antistatic
wrist strap and attaching it to a metal part of the computer chassis.
Safety Information
Before installing and using the device, note the following precautions:
▪Read all instructions carefully.
▪Do not place the unit on an unstable surface, cart, or stand.
▪Follow all warnings and cautions in this manual.
▪When replacing parts, ensure that your service technician uses parts
specified by the manufacturer.
▪Avoid using the system near water, in direct sunlight, or near a heating
device.
▪The load of the system unit does not solely rely for support from the
rackmounts located on the sides. Firm support from the bottom is highly
necessary in order to provide balance stability.
▪The computer is provided with a battery-powered real-time clock circuit.
There is a danger of explosion if battery is incorrectly replaced. Replace
only with the same or equivalent type recommended by the manufacturer.
Discard used batteries according to the manufacturer’s instructions.
Installation Recommendations
Ensure you have a stable, clean working environment. Dust and dirt can
get into components and cause a malfunction. Use containers to keep
small components separated.
Adequate lighting and proper tools can prevent you from accidentally
damaging the internal components. Most of the procedures that follow
require only a few simple tools, including the following:
• A Philips screwdriver
• A flat-tipped screwdriver
• A grounding strap
• An anti-static pad
Using your fingers can disconnect most of the connections. It is recom-
mended that you do not use needlenose pliers to disconnect connections
as these can damage the soft metal or plastic parts of the connectors.
Warning!
1. Handling the unit: carry the unit with both hands and handle it with care.
2. Maintenance: to keep the unit clean, use only approved cleaning products
or clean with a dry cloth.
3. CFast: Turn off the unit’s power before inserting or removing a CFast
storage card.
4. SIM: Do not insert or remove the SIM card when the system is powered
on. Always power off the system before inserting or removing the SIM
card.

Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. ix
Preface
VTC 7200-BK Series User Manual
Safety Precautions
▪Read these safety instructions carefully.
▪Keep this User Manual for later reference.
▪Disconnect this equipment from any AC outlet before cleaning. Use a
damp cloth. Do not use liquid or spray detergents for cleaning.
▪For plug-in equipment, the power outlet socket must be located near the
equipment and must be easily accessible.
▪Keep this equipment away from humidity.
▪Put this equipment on a stable surface during installation. Dropping it or
letting it fall may cause damage.
▪Do not leave this equipment in either an unconditioned environment or
in a above 40oC storage temperature as this may damage the equipment.
▪The openings on the enclosure are for air convection to protect the
equipment from overheating. DO NOT COVER THE OPENINGS.
▪Make sure the voltage of the power source is correct before connecting
the equipment to the power outlet.
▪Place the power cord in a way so that people will not step on it. Do not
place anything on top of the power cord. Use a power cord that has been
approved for use with the product and that it matches the voltage and
current marked on the product’s electrical range label. The voltage and
current rating of the cord must be greater than the voltage and current
rating marked on the product.
▪All cautions and warnings on the equipment should be noted.
▪If the equipment is not used for a long time, disconnect it from the power
source to avoid damage by transient overvoltage.
▪Never pour any liquid into an opening. This may cause fire or electrical
shock.
▪Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
▪If one of the following situations arises, get the equipment checked by
service personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work
according to the user’s manual.
e. The equipment has been dropped and damaged.
f. The equipment has obvious signs of breakage.
▪Do not place heavy objects on the equipment.
▪The unit uses a three-wire ground cable which is equipped with a third
pin to ground the unit and prevent electric shock. Do not defeat the
purpose of this pin. If your outlet does not support this kind of plug,
contact your electrician to replace your obsolete outlet.
▪CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE
RECOMMENDED BY THE MANUFACTURER. DISCARD USED BATTERIES
ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS.
▪The computer is provided with CD drives that comply with the appropriate
safety standards including IEC 60825.

Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. x
Preface
VTC 7200-BK Series User Manual
Conventions Used in this Manual
Warning:
Information about certain situations, which if not observed,
can cause personal injury. This will prevent injury to yourself
when performing a task.
CAUTION!
CAUTION!CAUTION! Caution:
Information to avoid damaging components or losing data.
Note:
Provides additional information to complete a task easily.
Technical Support and Assistance
1. For the most updated information of NEXCOM products, visit NEXCOM’s
website at www.nexcom.com.
2. For technical issues that require contacting our technical support team or
sales representative, please have the following information ready before
calling:
– Product name and serial number
– Detailed information of the peripheral devices
– Detailed information of the installed software (operating system,
version, application software, etc.)
– A complete description of the problem
– The exact wordings of the error messages

Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. xi
Preface
VTC 7200-BK Series User Manual
Global Service Contact Information
Headquarters
NEXCOM International Co., Ltd.
9F, No. 920, Chung-Cheng Rd.,
ZhongHe District, New Taipei City, 23586,
Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
www.nexcom.com
America
USA
NEXCOM USA
2883 Bayview Drive,
Fremont CA 94538, USA
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.com
Asia
Taiwan
NEXCOM Intelligent Systems
Taipei Office
13F, No.920, Chung-Cheng Rd.,
ZhongHe District,
New Taipei City, 23586, Taiwan, R.O.C.
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.com.tw
NEXCOM Intelligent Systems
Taichung Office
16F, No.250, Sec. 2, Chongde Rd.,
Beitun Dist.,
Taichung City 406, R.O.C.
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.com.tw
Japan
NEXCOM Japan
9F, Tamachi Hara Bldg.,
4-11-5, Shiba Minato-ku,
Tokyo, 108-0014, Japan
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom-jp.com
China
NEXCOM China
1F & 2F, Block A, No. 16 Yonyou Software Park,
No. 68 Beiqing Road, Haidian District,
Beijing, 100094, China
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.cn

Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. xii
Preface
VTC 7200-BK Series User Manual
Europe
United Kingdom
NEXCOM EUROPE
10 Vincent Avenue,
Crownhill Business Centre,
Milton Keynes, Buckinghamshire
MK8 0AB, United Kingdom
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.eu
Italy
NEXCOM ITALIA S.r.l
Via Lanino 42,
21047 Saronno (VA), Italia
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcomitalia.it
NEXCOM Shanghai
Room 603/604, Huiyinmingzun Plaza Bldg., 1,
No.609, Yunlin East Rd.,
Shanghai, 200333, China
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.cn
NEXCOM Surveillance Technology Corp.
Room202, Building B,
the GuangMing Industrial Zone Zhonghua Rd.,
Minzhi Street, Longhua District,
Shenzhen 518131, China
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.cn
NEXCOM United System Service
Hui Yin Ming Zun Building Room 1108,
Building No. 11, 599 Yunling Road, Putuo District,
Shanghai, 200062, China
Tel: [phone]
Fax: [phone]
Email: [email protected]
www.nexcom.cn

Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. xiii
Preface
VTC 7200-BK Series User Manual
Package Contents
Before continuing, verify that the VTC 7200-BK series package that you received is complete. Your VTC 7200-BK series package should have all the items listed
in the following table.
Item P/N Name Specification Qty
1 4NCPF00204X00 Terminal Blocks 2P Phoenix Contact:1777989 5.08mm Female DIP Green 1
2 4NCPM00302X00 (T)Terminal Blocks 3P Phoenix Contact:1777992 5.08mm Male DIP Green 1
3 4NCPM01601X00 Terminal Blocks 2x8 ANYTEK:KD161051A000G 3.5mm Male 16P 180D Plug Green 1
4 50311F0110X00 (H)Flat Head Screw Long FEI:F3x5ISO+NYLOK NIGP F3x5 NI Nylok 1
5 6012200052X00 PE Zipper Bag #8 170x240mm, w/China RoHS Symbol 1
6 6012200053X00 PE Zipper Bag #3 100x70mm, w/China RoHS Symbol 1
7 60233SAM05X00 GPS Antenna Arknav:A-130 GPS Antenna 5M SMA180P
R1 L3 For VTC 5M/SMA180P 1
8 602DCD0828X00 (N)VTC 72 Series DVD Driver VER:1.0 JCL 1

Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. xiv
Preface
VTC 7200-BK Series User Manual
Ordering Information
The following provides ordering information for VTC 7200-BK series.
▪VTC 7200-BK (P/N : 10V00720000X0)
Intel®Core™ processor i3-4010U, 1.7GHz dual core CPU, Industrial
Grade 2GB DDR3L SO-DIMM, VGA/DP output, 2 LAN, 2x RS-232, 1x RS-
232/422/485, 8x GPIO, 3x USB, 12VDC output
▪VTC 7210-BK (P/N : 10V00721000X0)
Intel®Core™ processor i5-4300U, 1.9GHz dual core CPU, Industrial
Grade 2GB DDR3L SO-DIMM, VGA/DP output, 2 LAN, 2x RS-232, 1x RS-
232/422/485, 8x GPIO, 3x USB, 12VDC output
▪VTC 7220-BK (P/N : 10V00722000X0)
Intel®Core™ processor i7-4650U, 1.7GHz, dual core CPU, Industrial
Grade 2GB DDR3L SO-DIMM, VGA/DP output, 2 LAN, 2x RS-232, 1x RS-
232/422/485, 8x GPIO, 3x USB, 12VDC output
▪VTC 7230-BK (P/N : 10V00723000X0)
Intel®Core™ processor i3-5010U, 2.1GHz, dual core CPU, Industrial
Grade 2GB DDR3L SO-DIMM, VGA/DP output, 2 LAN, 2x RS-232, 1x RS-
232/422/485, 8x GPIO, 3x USB, 12VDC output
▪VTC 7240-BK (P/N : 10V00724000X0)
Intel®Core™ processor i7-5650U, 2.2GHz, dual core CPU, Industrial
Grade 2GB DDR3L SO-DIMM, VGA/DP output, 2 LAN, 2x RS-232, 1x RS-
232/422/485, 8x GPIO, 3x USB, 12VDC output

Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. 1
Chapter 1: Product Introduction
VTC 7200-BK Series User Manual
Chapter 1: Product Introduction
Physical Features
Front View
SSD/HDD Antenna holes
Antenna holes
CFast Line-out2
SIM1 / SIM2
slot cover
Event
button
USB 2.0/3.0
ports
LED
indicators
COM1COM2COM3 MCU-DIO
GPS antenna hole
VGA GPIO/CAN/OBDII
DisplayPort DC OUT
Fuse
DC IN
9V-36V
LAN2 LAN1
USB 3.0 / USB 2.0Reset
Rear View
Mic2
Line-out1
Mic1

Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. 2
Chapter 1: Product Introduction
VTC 7200-BK Series User Manual
Overview
VTC 7200-BK series features powerful new generation Intel®Core™
processor i7-5650U/i7-4650U/i5-4300U/i3-5010U/i3-4010U. Its CPU
performance gives the users the ability to adapt to what they need in any
telematics applications. Its Intel®HD graphics 6000/5000 engine allows users
to fully take advantage of VTC 7200-BK series to achieve smooth, seamless
and stunning graphic performance on 3 different video outputs (VGA, DP,
LVDS). VTC 7200-BK series is equipped with 2 externally accessible SSD/HDD
trays; users can easily download or upload the data on other devices by just
removing the storage devices from VTC 7200-BK series. By integrating the
variety of I/O ports and 4x Mini-PCIe sockets expansibility, VTC 7200-BK
series is not only suitable for video surveillance application, but also can
meet the demand for other telematics applications, such as infotainment,
fleet management and dispatching system. With dual SIM cards support,
VTC 7200-BK series allows three SIM cards backup each other for a better
connectivity quality by software. In addition, three SIM cards + dual WWAN
modules architecture can increase the bandwidth for a faster data transfer
speed. Not only data transmission, VTC 7200-BK series also supports two-
way voice communication. Equipped with intelligent power management,
VTC 7200-BK series can be waked on by ignition, RTC timer or SMS/Ring
remotely.
Key Features
• Intel®Core™ processor dual core i7-5650U/i7-4650U/i5-4300U/
i3-5010U/i3-4010U
• Three SIM cards + dual WWAN modules support
• Dual accessible & hot swappable SATA 3.0 SSD/HDD (RAID 0/1)
• Built-in u-blox NEO-M8N module, optional dead reckoning support
• Built-in CAN 2.0B. Optional CAN/OBDII module
• Wake on RTC/SMS via WWAN module
• Voice communication via WWAN module
• Compliant with MIL-STD-810G
• 4x mini-PCIe socket rich expansion capability

Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. 3
Chapter 1: Product Introduction
VTC 7200-BK Series User Manual
Hardware Specifications
CPU
▪Intel®Core™ processor dual core i7-5650U, 2.2GHz
▪Intel®Core™ processor dual core i7-4650U, 1.7GHz
▪Intel®Core™ processor dual core i5-4300U, 1.9GHz
▪Intel®Core™ processor dual core i3-5010U, 2.1GHz
▪Intel®Core™ processor dual core i3-4010U, 1.7GHz
Memory
▪2 channel 204-pin DDR3L SO-DMIM socket support 1333/1600MHz up to
16GB, default industrial grade 2GB
Storage
▪2x 2.5” SATA 3.0 SSD/HDD (removable & hot swappable), RAID 0,1 supported
(optional lockable storage available)
▪1x CFast (externally accessible)
Expansion
▪1x full size Mini-PCIe socket (USB 2.0)
▪1x full size Mini-PCIe socket (USB 2.0 + PCIe)
▪1x full size Mini-PCIe socket (USB 2.0 + PCIe)
▪1x half size Mini-PCIe socket (USB 2.0 + PCIe)
GNSS Function
▪1x u-blox NEO-M8N module (support GPS/Gloness/QZSS/Galileo/Beidou)
or optional module with Dead Reckoning
▪Built-in G-sensor
I/O Interface-Front
▪4x LED for power, storage, WWAN, WLAN
▪2x 2.5” SATA 3.0 SSD/HDD (removable & hot swappable), RAID 0,1 supported
(optional lockable storage available)
▪1x dual USB type A connector for USB 3.0 port + USB 2.0 port
▪2x externally accessible SIM card socket (selectable)
▪1x phone jack 3.5mm for 1x Mic-in
▪1x phone jack 3.5mm for 1x Line-out
▪1x externally accessible CFast card socket with cover
▪1x event button (trigger type)
▪1x reset button
▪3x antenna hole for WWAN/WLAN/BT
I/O Interface-Rear
▪1x 9~36VDC input with ignition and 37W typical power consumption
▪1x dual USB type A connector for USB 3.0 port + USB 2.0 port
▪2x RJ45 10/100/1000 Fast Ethernet with LED
▪1x phone jack 3.5mm for 1x Mic-in
▪1x phone jack 3.5mm for 1x Line-out with 1.5W output each
▪1x DB-15 VGA. Resolution up to 2560 x 1600 @60Hz
▪1x DP port. Resolution up to 2560 x 1600 @60Hz
▪2x DB-9 RS-232
▪1x DB-9 RS-232/422/485 (RI/12V selectable)
▪1x DB-9 for CAN 2.0B (optional CAN Bus 2.0B mini-PCIe card),
2x MCU-DI and 2x MCU-DO
▪1x 16-pin terminal block
- 1x CAN Bus 2.0B (on board)
- 1x optional CAN/OBDII module (CAN Bus 2.0B or OBDII SAE J1939)
- 8x programmable GPIO
(Digital Input)
Input voltage (internal type): 5VDC TTL (default)
Input voltage (source type): 3~12VDC
(Digital Output)
Digital Output (sink type): 5VDC TTL (default), max current: 20mA
Digital Output (source type): 3~24VDC, max current: 150mA
▪1x 12VDC output (2A), SM Bus

Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. 4
Chapter 1: Product Introduction
VTC 7200-BK Series User Manual
▪4x antenna holes for WWAN/ WLAN/ BT/GPS
▪1x Fuse (15A)
Power Management
▪Selectable boot-up & shut-down voltage for low power protection by
software
▪Setting 8-level power on/off delay time by software
▪Status of ignition and low voltage can be detected by software
▪Support S3/S4 suspend mode
Operating System
▪Windows 8, WES8
▪Window 7, WES7
▪Linux kernel 3.X
Dimensions
▪260mm (W) x 206mm (D) x 79.5mm (H) (10.24” x 8.11” x 3.13”)
▪Weight: 2.5kg
Environment
▪Operating temperatures:
-30°C to 55°C (w/industrial SSD) with air flow
-10°C to 45°C (w/commercial HDD) with air flow
▪Storage temperatures: -35°C to 85°C
▪Relative humidity: 10% to 90% (non-condensing)
▪Vibration (random): 1.5g@5~500 Hz (in operation, HDD), 2g@5~500 Hz
(in operation, SSD)
▪Vibration (SSD/HDD):
Operating: MIL-STD-810G, Method 514.6, Category 4, common carrier
US highway truck vibration exposure
Storage: MIL-STD-810G, Method 514.6, Category 24, minimum
integrity test
▪Shock (SSD/HDD):
Operating: MIL-STD-810G, Method 516.6, Procedure I, functional
shock=20g
Non-operating: MIL-STD-810G, Method 516.6, Procedure V, crash
hazard shock test=75g
Standards/Certifications
▪CE approval
▪FCC Class B
▪E13 Mark

Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. 5
Chapter 1: Product Introduction
VTC 7200-BK Series User Manual
Connector Numbering
The following diagrams indicate the numbers of the connectors. Use these
numbers to locate the connectors’ respective pinout assignments on chapter
2 of the manual.
    

Copyright © 2013 NEXCOM International Co., Ltd. All Rights Reserved. 6
Chapter 2: External Connectors Pinout Description
VTC 7200-BK Series User Manual
Chapter 2: External Connectors Pinout Description
Event Button
Connector Number: 1
LED Indicators (HDD, WWAN, Power & WLAN)
Connector Number: 2
LED LED Behavior
HDD Light On: HDD/SSD Active
PWR Light On: Power On
Light Off: Power Off
WWAN Blinking: Active
WLAN Blinking: Active
HDD
21
PWR
WWAN
WLAN
Pin Definition
1 Event Input
2 GND