Nibe HA-WH5 F User guide

INDIRECTLY HEATED DOMESTIC HOT WATER CYLINDERS
FOR HEAT PUMPS AND OTHER ENERGY SOURCES
HA - WH5 F/FS
INSTALLER MANUAL
1. EDITION, 30.03.2015

HA-WH 5016 F
HA-WH 5020 F
HA-WH 5030 F
HA-WH 5020 FS
HA-WH 5030 FS

Table of Contents
1Importantinformation 4
Safety information 4
2Deliveryand handling 6
Transport 6
Assembly 6
Supplied components 6
3The water heater design 7
4 Pipe connections 8
8
10
12
12
General
Dimensions and pipe connections
Overall dimensions
Heat pump
Solar
Cold and hot water 13
Docking 13
5 Electrical installation 15
Sensors 15
Temperature limiter 16
6 Commissioning and adjusting 17
17
Filling andventing
Pressure drop diagram 18
7 Service and maintenance 19
Maintenance 19
Service actions 19
8 Technical specifications 20
Technical specifications 20
Item register 22
3Table of Contents |
11

Safety information
This manual describes installation and service procedures
for implementation by specialists.
This appliance is not intended for use by persons (includ-
ing children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concern-
ing use of the appliance by a person responsible for their
safety.
Children should be supervised to ensure that they do not
play with the appliance.
Rights to make any design or technical s are
reserved.
©NIBE 2015
Symbols
NOTE
This symbol indicates danger to water heater
or person.
Caution
This symbol indicates important information
about what you should observe when maintain-
ing your installation.
TIP
This symbol indicates tips on how to facilitate
using the product.
Serial number
The serial number can be found next to the front cover.
Caution
Always give the product's serial number when
reporting a fault.
Installer manual
This installer manual must be left with the customer.
Great Britain
This installation is subject to building regulation approval,
notify the local Authority of intention to install.
Use only manufacturer’s recommended replacement
parts.
Benchmark places responsibilities on both manufacturers
and installers. the purpose is to ensure that customers
are provided with the correct equipment for their needs,
that it is installed, commissioned and serviced in accord-
ance with the manufacturers instructions by competent
persons and that it meets the requirements of the appro-
priate Building Regulations. The Benchmark Checklist can
be used to demonstrate compliance with Building Regu-
lations and should be provided to the customer for future
reference.
Installers are required to carry out the installation, com-
missioning and servicing work in accordance with the
Benchmark Code of practice which is available from the
Heating and Hotwater Industry Council who manage and
promote the Scheme. Visit www.centralheating.co.uk for
information.
Chapter 1 | Important information4
1 Important information
Country c information
Let op!
Dit symbool geeft een waarschuwing aan
voor persoonlijk gevaar of voor de boiler zelf.
Attention!
Ce symbole indique un danger pour la
personne ou le chauffe-eau.
Achtung
Dieses Symbol weist auf eine Gefahr für
Heißwasserbereiter oder Mensch.
HUOM!
Tämä symboli merkitsee lämminvesivaraajaa
tai ihmistä uhkaavaa vaaraa.
Inspection of the installation
Current regulations require the heating installation to be inspected before it is commissioned. The inspection must be
carried out by a suitably d person.
DateSignatureNotesDescription
Hot water (page 14)
Shut valves
Expansion vessel
T&P valve
Tundish
Cold water (page 13 and 14)
Shut valves
Non-return valve
Mixing valve
Safety valve
Tundish
Electricity (page 16)
Hot water sensor
Temperature limiter
Miscellaneous
Benchmark checklist
5
Chapter 1 | Important information
4

Inspection of the installation
Current regulations require the heating installation to be inspected before it is commissioned. The inspection must be
carried out by a suitably d person.
DateSignatureNotesDescription
Hot water (page 14)
Shut valves
Expansion vessel
T&P valve
Tundish
Cold water (page 13 and 14)
Shut valves
Non-return valve
Mixing valve
Safety valve
Tundish
Electricity (page 16)
Hot water sensor
Temperature limiter
Miscellaneous
Benchmark checklist
5Chapter 1 | Important information

R
0
R
0
Assembly
The water heater is only designed for upright installa-
tion.
Position the water heater on a mbasethatcanbear
its weight, preferably on a concrete r or founda-
tion. Use the water heater’s adjustable feet to obtain
a horizontal and stable set-up.
Pipes must be routed from the safety valve to a suit-
able drain.
The water heater’s installation area should always
have a temperature of at least 10 °C and max 30 °C.
Chapter 2 | Delivery and handling6
2 Delivery and handling
Remember to rotate the cylinder in a direction that
allows easy access to the immersion heater and the
electrical box.
Transport
The HA - WH5 F / FS should be transported and
stored vertically in a dry place.

Chapter 3 | The water heater design 7
3 The water heater design
MEGA COIL 160, 200 & 300 L.
MEGA COIL - SOLAR 200 & 300 L.
(See page 8 for explanations)
HA - WH5 F 160, 200 & 300 L.
HA - WH5 FS 200 & 300 L.
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
E E
F F
Tegn, nr:
Erstatning for:
Filenavn:
Erstatt av:
Rev.
Målestokk:
Gen tol:
NS-ISO 2768 (Middels)
Kontrollert
Kontroll
Dato Konstr./ Tegnet
Godkjent
Varenummer:
1-115-001
09.05.2011 R-E N
HA-WH 5030 F.
Megacoil 300L EU.
N:\Utvikling\Tegninger\Produkter\1 Beredere\115 Ny EU\1-115-001.idw
Trippeveien 5
1618 Fredrikstad
1113006802
BT7
XL8 XL4 XL9
BT6
XL3
UL
PF3
XL3
BT6
XL9
XL4 BT7
XL8 XL5
TS1
XL5
FD1
PF4
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
E E
F F
Tegn, nr:
Erstatning for:
Filenavn:
Erstatt av:
Rev.
Målestokk:
Gen tol:
NS-ISO 2768 (Middels)
Kontrollert
Kontroll
Dato Konstr./ Tegnet
Godkjent
Varenummer:
1-114-001
09.02.2011 R-E N
HA-WH 5030 FS.
Megacoil / Solar 300L, EU.
N:\Utvikling\Tegninger\Produkter\1 Beredere\114 Ny EU m 2,Spi\1-114-001.idw
Trippeveien 5
1618 Fredrikstad
1113006804
XL13 BT7
XL9 XL8 XL14
XL3
UL
PF3
UA3
BT6
BT6
UA3
XL3
XL9
XL14
XL13
XL4
BT7
XL8
TS1
FD1
XL4
PF4

Pipe connections
Connection, cold water, 3/4” FXL3
Connection, hot water, Ø 22 mmXL4
XL5
Docking connection, flow line (from heat pump*), Ø 22 mm
XL8
Docking connection, return line (to heat pump*,
Ø 22 mm
XL9
Connection, w line (from solar heating system)
Ø 22 mm
XL13
Connection, return line (to solar heating system)
Ø 22 mm
XL14
HVAC components
Submerged tube for hot water sensor (display)
Submerged tube for hot water sensor (control)
Submerged tube for solar sensor (control)
BT7
BT6
UA3
Electrical components
Miscellaneous
Serial number plate
Adjustable feet
PF 3
PF 4
UL
Designations in component locations according to
standard IEC 81346-1 and 81346-2.
*or another external heat source
8 Chapter 3 | The water heater design
Cleaning the climate system
FD1
TS1
Temperature limiter immersion heater
Working thermostat immersion heater
When the water heater and the climate system have been filled with water, HA - WH5 F / FS must operate at maximum
normal temperature for at least one hour. Thereafter the system, must be drained of water and refilled.
Product/type plate
Connection, hot water circulation, Ø 1/2" F
(only HA-WH5 F 160-200-300L)

General
Pipe installation must be carried out in accordance with
current norms and directives.
Internal support bushes should be d when a plastic
pipe or annealed copper pipe is used. The water heater
must be d with the requisite valves, such as a safety
valve, valve, non-return valve, and vacuum valve.
An w pipe must be routed from the safety valve
to a suitable drain. The size of the w pipe must be
the same as on the safety valve. Route the w pipe
from the safety valve enclosed along its entire length and
ensure that it is frost proof. The outlet of the
pipe should be visible and clearly away from any electrical
components.
w water from the safety valves goes via non-
pressurised collecting pipes to a drain so that hot water
splashes cannot cause injury. These non-pressurised col-
lecting pipes shall not be used for anything else. A dis-
charge pipe from the tundish connected to the expansion
relief valve (safety valve) shall also be connected to a drain
in the same way.
Please note that the connection of the T&P-valve should
not be used for any other purpose.
Valves may not be positioned between the expansion
valve and the vessel.
Discharge pipes from tundishes shall have av vertical
section of pipe at least 300 mm long, before any elbows
or bends in the pipework (see following picture).
600 mm maximum
Tundish
Metal discharge pipe from
temperature relief valve to tundish.
Safety device
(e.g. temperature
relief valve).
300 mm
minimum
Metal discharge pipe from tundish,
with continous fall.
Possible wall
Discharge below
Trapped gulley
Fixed grating
NOTE
The expansion vessel accomodates expansion
that results from heating the water inside the
unit. The expansion vessel must be connected
between the expansion valve and the cylinder.
The location of the expansion vessel should allow
access to recharge the pressure as and when
necessary.
Resistance created by
each elbow or bend
Maximum resistance
allowed, expressed
as a lenght of
straight pipe (i.e. no
elbows or bends)
Minimum size of dis-
charge pipe from
tundish
Minimum size of dis-
charge pipe
Valve outlet size
0.8 mmup to 9 m22 mm15 mmG1/2
1.0 mmup to 18 m28 mm15 mmG1/2
1.4 mmup to 27 m35 mm15 mmG1/2
1.0 mmup to 9 m28 mm22 mmG3/4
1.4 mmup to 18 m35 mm22 mmG3/4
1.7 mmup to 27 m42 mm22 mmG3/4
1.4 mmup to 9 m35 mm28 mmG1
1.7 mmup to 18 m42 mm28 mmG1
2.3 mmup to 27 m54 mm28 mmG1
Hard water areas
Usually, there should not be a problem in installing Titanium
temperature is 50-60 °C.
Chapter 4 | Pipe connections 9
4 Pipe connections
in areas of hard water as the operating
Megacoil/Megacoil - Solar Coil
Emptying the system by
1. Open external r valve and external drain valve.
2. Flush the system for some minute. Watch out for water splashes from the safety valve.
3. Close the valves and check the stainer.
9

Dimensions and pipe connections
Connection
3/4" F
XL3 Cold water Ø
22mmXL4 Hot water Ø
1/2" F
XL5 Hot water circulation Ø (except 160 l.)
22mmXL8 Docking connection, w line Ø
22mmXL9 Docking connection, return line Ø
22mmXL13 Solar w line Ø
22mmXL14 Solar return line Ø
10 Chapter 4 | Pipe connections
Dimensions, pipe connections and setting-out coordinates
MEGACOIL 160, 200 & 300
MEGACOIL - SOLAR 200 & 300
HA - WH5 F 160, 200 & 300
HA - WH5 FS 200 & 300
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
E E
F F
Tegn, nr:
Erstatning for:
Filenavn:
Erstatt av:
Rev.
Målestokk:
Gen tol:
NS-ISO 2768 (Middels)
Kontrollert
Kontroll
Dato Konstr./ Tegnet
Godkjent
Varenummer:
1-115-001
09.05.2011 R-E N
HA-WH 5030 F.
Megacoil 300L EU.
N:\Utvikling\Tegninger\Produkter\1 Beredere\115 Ny EU\1-115-001.idw
Trippeveien 5
1618 Fredrikstad
1113006802
BT7
XL8 XL4 XL9
BT6
XL3
UL
PF3
XL3
BT6
XL9
XL4 BT7
XL8 XL5
TS1
XL5
FD1
PF4
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
E E
F F
Tegn, nr:
Erstatning for:
Filenavn:
Erstatt av:
Rev.
Målestokk:
Gen tol:
NS-ISO 2768 (Middels)
Kontrollert
Kontroll
Dato Konstr./ Tegnet
Godkjent
Varenummer:
1-114-001
09.02.2011 R-E N
HA-WH 5030 FS.
Megacoil / Solar 300L, EU.
N:\Utvikling\Tegninger\Produkter\1 Beredere\114 Ny EU m 2,Spi\1-114-001.idw
Trippeveien 5
1618 Fredrikstad
1113006804
XL13 BT7
XL9 XL8 XL14
XL3
UL
PF3
UA3
BT6
BT6
UA3
XL3
XL9
XL14
XL13
XL4
BT7
XL8
TS1
FD1
XL4
PF4

Dimensions and pipe connections
11Chapter 4 | Pipe connectionsVPB/VPBS UK
Megacoil-Solar
A-A ( 1:8 )
A
A
Følerlomme 50mm m/ Nippel M12
22 1
711344122PlastikkDekkskive Hvit 24x51mm PP TPE12 0
Følerlomme 120mm / Nippel M1211 9
711270091
EPSSkumspakning el-lokk
11 8
711344060PPSealing 3/4" Light grey11 7
711344057PPSealing 1/2" Light grey21 6
711239943PlastikkDekkskive hvit ø21-ø5041 5
711270011
/ 711270012
PP
PG-Nippel Ø10/M16x1,5mm M/mutter
11 4
711290011+
12
ABS PlasticPG-Nippel ø13, M20x1,5mm M/mutter
11 3
711344029ABS/PMMA
Lokk, NIBE, lysgrå, med hull.
11 2
711270084
SkumgummiSkumpakning ø20/ø80
1011
711239910EPDM 70
O ring 29,2x3mm
11 0 . 2
711230911MessingRør Nippel Overgang G1" ø22mm11 0 . 1
711290911RØRNIPPEL OVERG. 1"Ø22 MS11 0
711279919
N/AThermodisc (300075)(4011)
19
711344071GenericThermodisc. 66TM, Temp. 85 ±3°C18
711279918N/AThermodisc (300155)(4114)1
7
711300038
N/AO-Ring, 38x3,2mm
16
8025403CW602NElement 1.1/4 " 3 kW 230/400V, SMO,
1.4547
1
5
3-020-098Hvitlakkert
Y-Sarie 300LMegacoil-Solar
14
711231013Plastbunn, ø580 Lys. m/ben13
308060PP
Plast-topp, lys gråMecacoil solar EU.
12
1-114-002
HA-WH 5030 FS, Megacoil / Solar 300L.
11
Stykkliste
V.nr.-Tegn.MaterialeBeskrivelseAnt.Pos.
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
E E
F F
Tegn, nr:
Erstatning for:
Filenavn:
Erstatt av:
Rev.
Målestokk:
Gen tol:
NS-ISO 2768 (Middels)
Kontrollert
Kontroll
Dato Konstr./ Tegnet
Godkjent
Varenummer:
1-114-001
09.02.2011 R-E N
1248-001
1:8
HA-WH 5030 FS.
Megacoil / Solar 300L, EU.
N:\Utvikling\Tegninger\Produkter\1 Beredere\114 Ny EU m 2,Spi\1-114-001.idw
Trippeveien 5
1618 Fredrikstad
1113006804
12
13
2
5
6
1
274 (200L)
398 (300L)
410 (200L)
760 (300L)
414 (200L)
424 (300L)
424 (200L)
1019 (300L
121
1611
1617
1135 (200L)
1609 (300L)
3/4" F. Cold inlet.
Solar sensor
1/2" F
Temp. sensor
BT 6
1/2" F
Ø22mm(4x)
585
97,2
97,2
14
Primary return.
Heat Pump.
Ø22mm
Primary flow.
Solar.
Ø22mm
Primary return.
Solar.
Ø22mm
137,5
137,5
11
3
15
4
Temp. sensor
BT 7
1/2" F
130
585Ø
17
16
Thermostat and
high temp limiter
for immersed heat.
Primary flow
Heat Pump.
Ø22mm
21
Immersion
heater.
20
0-45
1/2"
10.1 10.2
Hot outlet
Ø22mm
137,5
B-B ( 1:8 )
711344122PlastikkDekkskive Hvit 24x51mm PP TPE219
Følerlomme 50mm m/ Nippel M12
118
Følerlomme 120mm / Nippel M12117
711344060PPSealing 3/4" Light grey116
711344057PP
Sealing 1/2" Light grey
115
711239943PlastikkDekkskive hvit ø21-ø50214
711270011
/ 711270012
PP
PG-Nippel Ø10/M16x1,5mm M/mutter
113
711290011ABS PlasticPG-Nippel ø13, M20x1,5mm M/mutter112
711344029ABS/PMMA
Lokk, NIBE, lysgrå, med hull.
111
711270084
SkumgummiSkumpakning ø20/ø80
810
711239910EPDM 70
O ring 29,2x3mm
19.2
711230911MessingRør Nippel Overgang G1" ø22mm19.1
711290911 RØRNIPPEL OVERG. 1"Ø22 MS19
711270091
EPSSkumspakning el-lokk
18
711279919N/AThermodisc (300075)(4011)1
7
711300038N/AO-Ring, 38x3,2mm16
8025403
CW602NElement 1.1/4 " 3 kW 230/400V, SMO,
1.4547
15
3-020-096Hvit LakkertYtterplate Megacoil UK 300L Stanset
Hvit
14
711231013Plastbunn, ø580 Lys. m/ben13
3-008-061PP
Plasttopp ø580 lys gråmed 5 stk. hull.
12
1-115-002300L, Megacoi, EU.11
Stykkliste
V.nr.-Tegn.MaterialeBeskrivelseAnt.Pos.
B
B
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
E E
F F
Tegn, nr:
Erstatning for:
Filenavn:
Erstatt av:
Rev.
Målestokk:
Gen tol:
NS-ISO 2768 (Middels)
Kontrollert
Kontroll
Dato Konstr./ Tegnet
Godkjent
Varenummer:
1-115-001
09.05.2011 R-E N
1252-001
1:8
Titanium Megacoil UK.
300L,30m spiral bereder,
N:\Utvikling\Tegninger\Produkter\1 Beredere\115 Ny EU\1-115-001.idw
Trippeveien 5
1618 Fredrikstad
3333003000
137,5 137,5
122
971 (160L)
1129 (200L)
1608 (300L)
4
97,2
Temp. sensor
BT 6
1/2" F
3/4" F. Cold inlet.
Primary return.
Heat Pump.
Ø22mm
Temp. sensor
BT 7
1/2" F
Primary flow.
Heat Pump.
Ø22mm
155
180
11
12
3
519 (160L)
540 (200L)
731 (300L)
13
14
1
8
9.1
137,5
10
Secondary return.
Hot outlet
Ø22mm
Thermostat and
temp limiter
immersion heater.
Immersion
heater.
585Ø
16
15
9.2
5
6
18
219
HA - WH5 F HA - WH5 FS

Heat pump connections
Connecting to heat pump or another external heat source
The heat pump supply and return are connected to HA - WH5 F.
Solar connections
Connecting to solar power, heat pump or external heat source
The solar heating system's supply and return are connected to the HA - WH5 FS.
12 Chapter 4 | Pipe connections
T&P valve
Install the pipe for the T&P valve as illustrated on page 9.
Heat pump connections
Connecting to heat pump
The heat pump supply and return are connected to Titanium Megacoil.
Solar connections
Connecting to solar power and heat pump
The solar heating system's supply and return are connected to the Titanium Megacoil- Solar Coil.
12 Chapter 4 | Pipe connections
(Except 160 litre)
A-A ( 1:8 )
A
A
Følerlomme 50mm m/ Nippel M12
221
711344122PlastikkDekkskive Hvit 24x51mm PP TPE120
Følerlomme 120mm / Nippel M12119
711270091
EPSSkumspakning el-lokk
118
711344060PPSealing 3/4" Light grey117
711344057PPSealing 1/2" Light grey216
711239943PlastikkDekkskive hvit ø21-ø50415
711270011
/ 711270012
PP
PG-Nippel Ø10/M16x1,5mm M/mutter
114
711290011+
12
ABS PlasticPG-Nippel ø13, M20x1,5mm M/mutter
113
711344029ABS/PMMA
Lokk, NIBE, lysgrå, med hull.
112
711270084
SkumgummiSkumpakning ø20/ø80
1011
711239910EPDM 70
O ring 29,2x3mm
110.2
711230911MessingRør Nippel Overgang G1" ø22mm110.1
711290911 RØRNIPPEL OVERG. 1"Ø22 MS110
711279919
N/AThermodisc (300075)(4011)
19
711344071GenericThermodisc. 66TM, Temp. 85 ±3°C18
711279918N/AThermodisc (300155)(4114)1
7
711300038
N/AO-Ring, 38x3,2mm
16
8025403CW602NElement 1.1/4 " 3 kW 230/400V, SMO,
1.4547
1
5
3-020-098Hvitlakkert
Y-Sarie 300LMegacoil-Solar
14
711231013Plastbunn, ø580 Lys. m/ben13
308060PP
Plast-topp, lys gråMecacoil solar EU.
12
1-114-002
HA-WH 5030 FS, Megacoil / Solar 300L.
11
Stykkliste
V.nr.-Tegn.MaterialeBeskrivelseAnt.Pos.
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
E E
F F
Tegn, nr:
Erstatning for:
Filenavn:
Erstatt av:
Rev.
Målestokk:
Gen tol:
NS-ISO 2768 (Middels)
Kontrollert
Kontroll
Dato Konstr./ Tegnet
Godkjent
Varenummer:
1-114-001
09.02.2011 R-E N
1248-001
1:8
HA-WH 5030 FS.
Megacoil / Solar 300L, EU.
N:\Utvikling\Tegninger\Produkter\1 Beredere\114 Ny EU m 2,Spi\1-114-001.idw
Trippeveien 5
1618 Fredrikstad
1113006804
12
13
2
5
6
1
274 (200L)
398 (300L)
410 (200L)
760 (300L)
414 (200L)
424 (300L)
424 (200L)
1019 (300L
121
1611
1617
1135 (200L)
1609 (300L)
3/4" F. Cold inlet.
Solar sensor
1/2" F
Temp. sensor
BT 6
1/2" F
Ø22mm(4x)

585
97,2
97,2
14
Primary return.
Heat Pump.
Ø22mm
Primary flow.
Solar.
Ø22mm
Primary return.
Solar.
Ø22mm
137,5
137,5
11
3
15
4
Temp. sensor
BT 7
1/2" F
130
585Ø
17
16
High temp limite
motorized valve
solar.
High temp limiter
motorized valve
thermostat optiond
Thermostat and
high temp limiter
for immersed heat.
Primary flow
Heat Pump.
Ø22mm
21
Immersion
heater.
20
0-45
1/2"
10.1 10.2
Hot outlet
Ø22mm
137,5
B-B ( 1:8 )
711344122PlastikkDekkskive Hvit 24x51mm PP TPE219
Følerlomme 50mm m/ Nippel M12
118
Følerlomme 120mm / Nippel M12117
711344060PPSealing 3/4" Light grey116
711344057PP
Sealing 1/2" Light grey
115
711239943PlastikkDekkskive hvit ø21-ø50214
711270011
/ 711270012
PP
PG-Nippel Ø10/M16x1,5mm M/mutter
113
711290011ABS PlasticPG-Nippel ø13, M20x1,5mm M/mutter112
711344029ABS/PMMA
Lokk, NIBE, lysgrå, med hull.
111
711270084
SkumgummiSkumpakning ø20/ø80
810
711239910EPDM 70
O ring 29,2x3mm
19.2
711230911MessingRør Nippel Overgang G1" ø22mm19.1
711290911 RØRNIPPEL OVERG. 1"Ø22 MS19
711270091
EPSSkumspakning el-lokk
18
711279919N/AThermodisc (300075)(4011)1
7
711300038N/AO-Ring, 38x3,2mm16
8025403
CW602NElement 1.1/4 " 3 kW 230/400V, SMO,
1.4547
15
3-020-096Hvit LakkertYtterplate Megacoil UK 300L Stanset
Hvit
14
711231013Plastbunn, ø580 Lys. m/ben13
3-008-061PP
Plasttopp ø580 lys gråmed 5 stk. hull.
12
1-115-002300L, Megacoi, EU.11
Stykkliste
V.nr.-Tegn.MaterialeBeskrivelseAnt.Pos.
B
B
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
E E
F F
Tegn, nr:
Erstatning for:
Filenavn:
Erstatt av:
Rev.
Målestokk:
Gen tol:
NS-ISO 2768 (Middels)
Kontrollert
Kontroll
Dato Konstr./ Tegnet
Godkjent
Varenummer:
1-115-001
09.05.2011 R-E N
1252-001
1:8
HA-WH 5030 F.
Megacoil 300L EU.
N:\Utvikling\Tegninger\Produkter\1 Beredere\115 Ny EU\1-115-001.idw
Trippeveien 5
1618 Fredrikstad
1113006802
137,5 137,5
122
971 (160L)
1129 (200L)
1608 (300L)
4
97,2
Temp. sensor
BT 6
1/2" F
3/4" F. Cold inlet.
Primary return.
Heat Pump.
Ø22mm
Temp. sensor
BT 7
1/2" F
Primary flow.
Heat Pump.
Ø22mm
155
180
11
12
3
519 (160L)
540 (200L)
731 (300L)
13
14
1
8
9.1
10
Secondary return.
1/2" F
Hot outlet
Ø22mm
Thermostat and
temp limiter
immersion heater.
Immersion
heater.
585Ø
16
15
9.2
5
6
18
2
19
97,2
137,5
0-45
7
1577
180

Cold and hot water
Connecting cold and hot water
There must be a mixing valve if the temperature can ex-
ceed 60 °C.
Connecting hot water circulation
HA - WH5 FS 200 & 300 hav e a connection that allows hot
water circulation.
To reduce the risk of bacterial growth in systems with
hot water circulation, the temperature of the circulating
water should not fall below 50 °C. There should not be
any non-circulatory hot water pipes. Adjust the hot water
system so that the temperature does not fall below 50°C
at the ends of the system.
Docking
HA - WH5 FS 200 & 300 can be connected in several
dierent ways, one of which is shown here.
Further option information is available at www.nibe.eu
and in the respective assembly instructions for the heat
pumps used.
Chapter 4 | Pipe connections 13
Symbol key
MeaningSymbol
Venting valve
valve
Non-return valve
Mixing valve
Safety valve
Drain off
Temperature sensor
Circulation pump
Particle
Motorized valve
Inlet valves according to local legislation
/ Three way valve

To gas boiler
Titanium Megacoil/ Megacoil - Solar can be docked with another heat source,
for example a gas boiler.
To solar heating
Titanium Megacoil/ Megacoil - Solar can be
docked to solar heating system.
14 Chapter 4 | Pipe connections
To air/water heat pump
Titanium Megacoil/Megacoil-Solar can be docked with
heat pump, for example NIBE air/water heat pump.
P
P
P
P
-BT12
-AA25
-EB1
-BT3
-BT1
To solar heating
HA - WH5 FS can be docked to a solar heating system in
addition to the F2040 heat pump.
P
-BT12
-AA25
-EB1
-BT3
-BT1
To air source heat pump
HA - WH5 FS can be docked with an air to water
heat pump, eg. NIBE 2040

NOTE
Sensors (See page 11)
The HA - WH5 F can accommodate up to two hot water sensors, one for SMO controller display and one to control start and
stop of heat pump.
Chapter 5 | Electrical installation 15
5 Electrical installation
The display sensor is positioned in the submerged tube for the display sensor (BT7) and the control sensor in the
submerged tube for control sensor (BT6). In cases where it is only possible to connect one sensor, use the submerged tube
for control sensor (BT6).
The HA - WH5 FS can also be supplemented with a solar sensor. This is placed in the submerged tube for solar sensor.
Use the sensors provided with the heat pump/control module. When no heat sensors have been provided, these must be
ordered from the manufacturer of the heatpump/control module.
Thermostats and temperature limiter (Factory tted)
Electrical installation and service must be carried out under the supervision of a qualified electrician. Electrical
installation and wiring must be carried out in accordance with the stipulations in force.
Achtung
Die elektrische Installation und Service müssen unter einer Kontrolle von qualifizierten Elektriker durchgeführt
werden. Elektische Installation und Verkabelung muss gemäß den geltenden Vorschriften durchgeführt werden.
HUOM!
Sähköasennukset ja mahdolliset huollot saa tehdä vain valtuutetun sähköasentajan valvonnassa.
Sähköasennukset ja johtimien veto on tehtävä voimassa olevien määräysten mukaisesti.
OPMERKING
Werkzaamheden aan de elektrische installatie, bij installatie of service, dient te worden uitgevoerd door een
gekwalificeerde elektricien. De elektrische installatie en aansluitingen hiervan dienen in overeenstemming te
zijn met van toepassing zijnde regelgeving.
NOTE
L'installation électrique et le service doit être effectuées sous la supervision d'un électricien qualifié.
L'installation et le raccordement électrique doit être effectuées conformément aux dispositions applicables.
MEGA COIL 160, 200 & 300
HA - WH5 FS 200 & 300 L. HA - WH F 160, 200 & 300 L.

Temperature limiters
Power supply to temperature limiter (FD1) is 230 V.
Temperature limiter wiring diagram
16 Chapter 5 | Electrical installation
Immersion heater wiring diagram
Megacoil Solar Models
Megacoil Models
HA - WH5 FS 200 & 300 L.
HA - WH F 160, 200 & 300 L.

Filling and venting
Filling the hot water heater
1. Open a hot water tap in the house. (XL4)
2. Fill the hot water heater through the cold water
connection (XL3).
3. When the water that comes out of the hot water tap
is no longer mixed with air, the water heater is full.
and the tap can
be closed.
Filling and venting the charge coil
Filling and venting
1. Open the g valve (external, not included with the
product). Fill the coil in the hot water heater and the
rest of the climate system with water.
2. Vent the coil of the climate system via
the relevant venting valves.
3. Keep topping up and venting until all air has been
removed and the pressure is correct.
The e shows Mega Coil 160, 200 and 300
Chapter 6 | Commissioning and adjusting 17
6 Commissioning and adjusting
and the rest
Flush the system for several minutes
Cold inlet
XL3
XL4

Pressure drop diagram
Pressure drop diagram, charge coil
Docking connection, w line (XL8) and docking connec-
tion, return line (XL9).
Titanium Megacoil 160
Titanium Megacoil 200
Pressure drop diagram, solar coil
Connection, w line solar heating system (XL13) and
connection, return line solar heating system (XL14).
Titanium Megacoil - Solar 200
18 Chapter 6 | Commissioning and adjusting
Titanium Megacoil - Solar 300
Titanium Megacoil 300
Pressure drop
Flow
Flow
Pressure drop
Flow
Pressure drop
Flow
Pressure drop Pressure drop
Flow
Pressure drop
Flow
Pressure drop
Flow
Megacoil
HP coil
HA - WH5 F 160 - HP Coil HA - WH5 FS
HA - WH5 FS
HA - WH5 FS 300 - HP coil
HA - WH5 FS 300 - Solar coil
HA - WH5 FS 300 - Solar and HP coil
HA - WH5 F 200 - HP Coil
HA - WH5 F 300 - HP Coil

NOTE
Any servicing must be carried out byacompet-
ent person.
Maintenance
General inspection - Check the following:
1. Condition of casing.
2. Electrical connections.
3. Pipe connections.
Correct any fault before continuing.
NOTE
Do not remove or adjust any components that
arepart of thispressurisedwaterheater.Contact
your installer!
NOTE
If this pressurised water heater develops a fault, e.g. a
flow of hot water from the overflow pipe, turn the heat
pump offand contact your in-staller.
Cleaning
Inspect and clean the water heater by using a suitable
instrument such as an endoscope. The hot water connec-tion
(XL4) must be removed to facilitate access.
Emptying
The water heater is emptied through the drain cock in the
cold water connection (XL3).
Drain the charge coil through the siphon (with hose) on the
docking connection, return to heat pump (XL9).
Drain the solar coil through the siphon (with hose) on the
connection, return to solar heating system (XL14).
Chapter 7 | Service and maintenance 19
7 Service and maintenance
OPMERKING
Servicewerkzaamheden dienen uitgevoerd te
worden door gekwalificeerd personeel.
NOTE
Tout les opérations de services doivent être
effectué par une personne compétente.
Achtung
Jeder Service soll von einer qualifizierten
Person durchgeführt werden.
HUOM
Laitetta saa hoitaa vain sen toimintaan
perehtynyt henkilö. Laitetta saa huoltaa vain
ammattitaitoinen asentaja ja lämpöpumppua
saa huoltaa vain sertifioitu asentaja.
Sähköasennuksia saa huoltaa vain sertifioidun
sähköasentajan valvonnassa.
OPMERKING
Indien deze onder druk staande boiler een mogelijk
mankement vertoont, bijv. bij waterlekkage: zet de
warmtepomp (of ketel) uit en raadpleeg uw installateur.
NOTE
Si ce chauffe-eau tombe en panne, par exemple une fuite,
arrêtez la pompe à chaleur, et contactez votre installateur.
ACHTUNG
Wenn es einen Fehler an Druck-Heißwasserbereiter gibt
z.B.: Varmwasserausfluß aus Überlaufrohr schalten Sie die
Wärmepumpe aus und treten Sie in Kontakt mit Ihrem
Installateur.
HUOM
Mikäli tämä paineistettu vesivaraaja vikaantuu, mm.
kuuma vesi virtaa ylivuotoputkesta, kytke
lämpöpumppu pois päältä ja ota yhteys asentajaan.
OPMERKING
Verwijder geen enkel onderdeel van deze onder
waterdruk staande boiler. Pas ook geen
component aan. Raadpleeg bij vragen altijd uw
installateur.
NOTE
N’enlever ou ajuster pas les composants qui
font partie du chauffe-eau sous pression.
Contactez votre installateur!
ACHTUNG
Keine Komponente, die ein Teil dieses Heiß-
wasserbereiter unter Druck sind, entfernen oder
regulieren. Tritt in Kontakt mit Ihrem Installateur!
HUOM
Älä poista tai muuta mitään osaa, joka on
kuuluu tähän paineistettuun vesivaraajaan. Ota
yhteys asentajaan!
C-C ( 1 : 7 )
C
C
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
E E
F F
Tegn, nr:
Erstatning for:
Filenavn:
Erstatt av:
Rev.
Målestokk:
Gen tol:
NS-ISO 2768 (Middels)
Kontrollert
Kontroll
Dato Konstr./ Tegnet
Godkjent
Varenummer:
1-115-001
09.05.2011 R-E N
HA-WH 5030 F.
Megacoil 300L EU.
N:\Utvikling\Tegninger\Produkter\1 Beredere\115 Ny EU\1-115-001.idw
Trippeveien 5
1618 Fredrikstad
1113006802
XL3
XL9
HA - WH5 F 160, 200 & 300
HA - WH5 FS 200 & 300

8 Technical
HA-WH5 F
179litreVolume (net)
8,5litreVolume, charge coil
45 59kgNet weight
224 330kg 190,5Gross weight
150/83,9 214/79litre/% 126,9/85,5
8,16 12,58kWh 6,89Heat content at 50°C*
234 361litre 198Equivalent amount of hot water (40°C)*
7,3 7,3kW 6,2Re-heat performance
50 91min. 46Re-heating time to 60°C, 70% of the total volume
75°CMax operating temperature
3/0.3bar/MPaMax pressure, primary side
bar/MPaMax pressure, water heater
bar/MPaMax water supply pressure
1,85 2,59kW/24 hrs 1,72Heat loss ∆t 45°C
Part No. 081028 081029 081030
Chapter 8 | Technical data20
160 litre 200 litre 300 litre
75 75
3/0.3 3/0.3
10/1,0
148,5 271
8,1 10,6
Max temperature heat pump °C 75 75 75
Max recommended heat pump size kW 12 12 12
42
Drawn o capacity
* Cold water temperature = 10°C
Immersion heater 230 V kW 3,0 3,0 3,0
10/1,0 10/1,0
10/1,0 10/1,0 10/1,0
8 Technical
Titanium Megacoil
179litreVolume (net)
8,5litreVolume, charge coil
45 59kgNet weight
224 330kg 190,5Gross weight
150/83,9 214/79litre/% 126,9/85,5
8,16 12,58kWh 6,89Heat content at 50°C*
234 361litre 198Equivalent amount of hot water (40°C)*
7,3 7,3kW 6,2Re-heat performance
50 91min. 46Re-heating time to 60°C, 70% of the total volume
85°CMax operating temperature
3/0.3bar/MPaMax pressure, primary side
5,5/0,55bar/MPaMax pressure, water heater
16/1.6bar/MPaMax water supply pressure
3.0/0.3bar/MPaExp. vessel, tap water, charge pressure
6/0.6bar/MPaExpansion relief valve, setting
7/0.7bar/MPaMax operating pressure, T&P-valve
95°CMax operating temperature, T&P-valve
1,85 2,59kW/24 hrs 1,72Heat loss ∆t 45°C
Part No. 081005 081007 081008
Chapter 8 | Technical data20
160 (156) litre 200 (187,6) litre 300 (281,7) litre
85 85
3.0/0.3 3.0/0.3
3/0.3 3/0.3
5,5/0,55 5,5/0,55
16/1.6 16/1.6
6/0.6 6/0.6
7/0.7 7/0.7
95 95
148,5 271
8,1 10,6
Set pressure reducing valve bar/MPa 33 3
Max temperature heat pump °C 75 75 75
Max recommended heat pump size kW 12 12 12
Volume expansion vessel litre 18 18 24
42
Drawn o capacity
* Cold water temperature = 10°C