Nilfisk-Advance MC 2C-180 PE User manual

MC DE, MC PE, MC PE PLUS -
Instructions for use
106169306 c (09.2015)
EN-DE-FR-NL-ES-DA-NO-SV-FI

Copyright © 2015 Nilfisk A/S
User manual ...................................................................................................................... 3 - 17
Betriebsanleitung............................................................................................................... 18 - 33
Manuel d‘instructions......................................................................................................... 34 - 48
Gebruikershandleiding....................................................................................................... 49 - 64
Manuale di istruzioni.......................................................................................................... 65 - 80
Instruktionsbog .................................................................................................................. 81 - 96
Instruksjonsbok.................................................................................................................. 97 - 111
Instruktionsbok .................................................................................................................. 112 - 126
Käyttöohje.......................................................................................................................... 127 -141

3
MC DE, MC PE, MC PE PLUS
Original Instructions
Contents
1 Safety Precautions and Warnings ................................................................................................4
2 Description .....................................................................................................................................5
2.1 Intended use.............................................................................................................................5
2.2 Operating elements ..................................................................................................................5
3 Before starting the pressure washer ...........................................................................................6
3.1 Setting up the pressure washer (does not apply to MC 2C-180/700 PE /
MC 3C-165/810 PE) .................................................................................................................6
4 Operation and use .........................................................................................................................6
4.1 Connections..............................................................................................................................6
4.1.1 Connecting the lance to the spray gun ..........................................................................6
4.1.2 Connecting the high pressure hose and the water hose ...............................................7
4.1.3 Fuelling..........................................................................................................................7
4.2 Start the washer .......................................................................................................................7
4.2.1 Switching on the washer when it is connected to a water supply..................................7
4.2.2 Switching on the washer when it is connected to open tanks (suction mode) ..............8
4.2.3 Start machine ................................................................................................................8
4.3 Using detergents ......................................................................................................................9
5 After using the washer ..................................................................................................................9
5.1 Stop the pressure washer.........................................................................................................9
5.2 Disconnecting supply lines .....................................................................................................10
5.3 Storing the washer (frost-protected)......................................................................................10
6 Maintenance .................................................................................................................................11
6.1 Maintenance plan ...................................................................................................................11
6.2 Maintenance work ..................................................................................................................11
6.2.1 Clean water filter .........................................................................................................11
6.2.2 Clean high pressure nozzle.........................................................................................11
6.2.3 Checking the oil level (does not apply to MC 2C-180/700 PE / ..................................12
MC 3C-165/810 PE) ....................................................................................................12
6.2.4 Changing the pump/gear oil (does not apply to MC 2C-180/700 PE /
MC 3C-165/810 PE) ....................................................................................................12
6.2.5 Check of V-belts...........................................................................................................13
7 Troubleshooting ...........................................................................................................................14
8 Further information......................................................................................................................15
8.1 Recycling the pressure washer ..............................................................................................15
8.2 Guarantee...............................................................................................................................15
8.3 Technical data.........................................................................................................................16
8.4 EC Declaration of Conformity .................................................................................................17

4
MC DE, MC PE, MC PE PLUS
Original Instructions
Symbols used to mark instructions
Before starting
up your high-
pressure washer
for the first time,
this instruction
manual must be read through
carefully. Save the instructions
for later use.
Safety instructions
marked with this
symbol must
be observed to
prevent danger
to persons.
This symbol is used
to mark safety
instructions
that must be
observed to prevent
damage to the machine and its
performance.
This symbol
indicates tips
and instructions to
simplify work and to
ensure a safe operation.

1 Safety Precautions and Warnings
High Pressure Washer -
SAFETY INSTRUCTIONS
107141898 D (07-2015)

5
MC DE, MC PE, MC PE PLUS
Original Instructions
2 Description
2.1 Intended use This high pressure washer has
been designed for professional
use in
2.2 Operating elements
1 Start/stop switch
2 Lance
3 Holder for lance
4 Holder for high pressure hose
5 High pressure hose
6 Spray gun
7 Water connection and water
inlet filter
8 Connection for high pressure
hose
9 Detergent hose
10 Oil level gauge
11 Regulation of water volume
12 Filling of oil
13 Handle
- agriculture
- transport industry
- construction industry
etc.
WARNING! Do not use combustion engine powered machines indoors unless adequate ventilation
is assessed by national labour authorities.
WARNING! Ensure, that any exhaust emissions are not in a vicinity of air intakes.
WARNING! Incorrect fuels shall not be used as they may prove hazardous.

6
MC DE, MC PE, MC PE PLUS
Original Instructions
3 Before starting the pressure washer
3.1 Setting up the pressure
washer (does not apply
to MC 2C-180/700 PE /
MC 3C-165/810 PE)
1. Before using the pressure
washer for the first time,
check it carefully to detect
any faults or damage.
2. In the event of any damage
contact your Nilfisk dealer
immediately.
3. Check whether the oil level
is in the middle of the oil
inspection glass, oil cup or
dip stick. This also applies to
machines with gear.
4 Operation and use
4.1 Connections
4.1.1 Connecting the lance to
the spray gun
1. Pull the blue quick-release
grip (A) of the spray handle
backwards.
2. Insert the nipple of the spray
lance (B) into the quick-
release connection and
release it.
3. Pull forward the spray lance
or any other accessory to
ensure correct mounting
before starting the machine.
NOTE!
Always remove any dirt from
the nipple before connecting
the lanse to the spray gun.
A
B

7
MC DE, MC PE, MC PE PLUS
Original Instructions
4.1.2 Connecting the high
pressure hose and the
water hose
1. Connect the high pressure
hose to the high pressure
inlet by means of the quick
coupling. Use max. 50 m
extension hose.
2. Before connecting the water
hose to the washer, rinse the
water hose briefly to prevent
sand and other dirt from
entering into the washer.
3. Open the tap.
NOTE!
See chapter 8.3 for required
quantity of water and water
pressure.
In the case of poor water quality
(sand, etc.), we recommend
that a fine water filter is fitted in
the water inlet.
4.1.3 Fuelling WARNING!
Always shut off the engine
and let it cool for at least two
minutes before fuelling.
Avoid spilling fuel.
If you do spill fuel when fuelling,
do not start the engine before
the spilled fuel has evaporated.
If the washer is on a trailer, any
fuel spills must be wiped up
before the machine is started.
Never expose the machine
to an open flame. Smoking is
prohibited during fuelling. Also
read the operating manual for
the fuel engine.
Note: Never operate the
machine in a closed room; the
exhaust fumes are dangerous.
Follow the safety instructions
in chapter 1!
4.2 Start the washer
4.2.1 Switching on the
washer when it is
connected to a water
supply
2. Unlock the spray gun and
activate it.
3. Lock the safety catch even
during short pauses.
NOTE!
Activate the spray
gun several times
at short intervals to vent the
system.
If it requires too much power to
start the engine, it can be
facilitated by removing the
spray lance and activate the
spray gun during startup.
1. Start the engine. (See the
operating manual for the fuel
engine.)

8
MC DE, MC PE, MC PE PLUS
Original Instructions
4.2.2 Switching on the
washer when it is
connected to open
tanks (suction mode)
1. Before connecting the suction
hose to the washer, fill the
hose with water.
2. Start the washer.
3. Unlock the spray gun and
activate it.
4. When using this machine in
suction mode, first ensure
that the system has been
bled of air by letting the
machine run without high
pressure hose and spray
lance mounted until all air
has escaped. On some
models you need to kink
the by-pass hose and / or
move the engine throttle to
minimum position to achieve
enough suction power.
During work breaks of more
than three minutes, switch off
the washer.
NOTE!
For automatic
suction from a tank, watercourse
or similar supply, the inlet hose
must be filled with water before
you start. The suction height
depends on the water tempe-
rature. Max. suction height (see
section 8.3 Technical Data) is
reached with cold water (up to
8°C). With 60°C warm water, the
machine must be under or at the
water level.
If the water being suctioned
contains particles, a suction
filter must be mounted on the
end of the hose.
In case of risk of running sands,
a sand filter must be attached.
4.2.3 Start machine
Start MC PE with electric starter
1. Start the engine by turning
the key (see the operating
instructions for the engine.
2. Check that the throttle lever
is adjusted correctly - need to
be in Run position.
Start MC DE 1. Switch on the ignition by
pushing the ON/OFF button
of the machine. The charging
+ oil light indicators will turn
on.
2. Move the throttle lever to
SLOW or RUN position.
3. Push the start button until
the machine starts. Now the
charging + oil light indicators
will turn off. If not, stop
the machine immediately
and contact Nilfisk service
department.
4. The machine can be started
by means of the starter rope
if the battery has gone flat.
See manual from Yanmar.

9
MC DE, MC PE, MC PE PLUS
Original Instructions
4.3 Using detergents Detergent can be added by
means of the detergent injector.
1. Dilute detergent according
to the manufacturer's
instructions.
2. Set the pressure to the
lowest setting on the lance.
CAUTION!
Never allow
detergent to dry on
the surface to be cleaned as
this may cause damage.
5 After using the washer
5.1 Stop the pressure washer
1. Stop the engine.
2. Close the tap.
3. Operate the spray gun until
the wasser is depressurized.
4. Lock the safety catch.
Switching off MC PE with electric start
1. Stop the washer by moving
the throttle lever to STOP
position.
2. Switch off the ignition by
turning the key to OFF
position.

10
MC DE, MC PE, MC PE PLUS
Original Instructions
5.2 Disconnecting supply
lines
1. Shut the fuel cock.
2. Remove the water hose from
the washer.
5.3 Storing the washer
(frost-protected)
1. Store the pressure washer in
a dry room without danger of
frost.
IMPORTANT!
If the high-pressure washer
is stored in a room with
temperatures around or
below 0°C, anti-freeze should
be drawn into the pump
beforehand:
1. Remove the water inlet hose
from the washer.
2. Remove the lance.
3. Start the washer and stop it
again after max. one minute.

4. Connect the suction hose
to the water inlet of the
washer and place it in a tank
containing anti-freeze.
5. Start the washer.
6. Hold the spray gun over the
tank containing anti-freeze
and activate it to start suction
of anti-freeze.
7. During suction operate the
spray gun two or three times.
8. Lift the suction hose from the
tank containing anti-freeze
and activate the spray gun to
pump out the remaining anti-
freeze.
9. Stop the washer.
Switching off MC DE
1. Stop the washer by moving
the throttle lever to STOP
position.
2. Switch off the ignition by
pushing the ON/OFF button.
The light indicators will now
turn off.

11
MC DE, MC PE, MC PE PLUS
Original Instructions
6 Maintenance
6.1 Maintenance plan
weekly
every six
months or
500 operating
hours
as required
6.2.1 Clean water filter •
6.2.2 Clean high pressure nozzle •
6.2.3 Check oil level •
6.2.4 Change oil - Note: First time after 50 hours •
6.2.5 Check belts (only belt driven units) •
Maintenance of motor according to separate operating instructions from the engine supplier
6.2 Maintenance work
6.2.1 Clean water filter
A water filter is fitted on the
water inlet to prevent large
particles of dirt from entering
into the pump.
1. Unscrew the union nut.
2. Remove the filter and rinse it.
Replace damaged filter.
3. Tighten the union nut gently,
so as to avoid damaging the
gasket.
6.2.2 Clean high pressure
nozzle
A blocked nozzle causes
excessive pump pressure. It
must therefore be cleaned
immediately.
1. Stop the washer.
2. Remove the lance.
3. Clean the nozzle with a
needle.
4. Rinse the lance with water
from the nozzle side.
WARNING!
Use the cleaning needle only
when the spray lance has been
removed.
NOTE!
The fuel engine
stops automatically
if the oil level is low. You can
start the petrol engine again
once you have added oil (does
not apply to MC 2C-180/700
PE).

12
MC DE, MC PE, MC PE PLUS
Original Instructions
6.2.3 Checking the oil level
(does not apply to
MC 2C-180/700 PE /
MC 3C-165/810 PE)
1. Check whether the oil level
is in the middle of the oil
inspection glass, oil cup or
dip stick. Top up with oil if
necessary (see section 8.3
for type of oil).
6.2.4 Changing the pump/
gear oil (does not apply
to MC 2C-180/700 PE /
MC 3C-165/810 PE)
1. Before changing the oil,
allow the pressure washer to
become warm.
2. Unscrew/open the plugs/lid at
the top and the bottom of the
pump.
3. Allow the oil to drain into a
suitable container (min. 1 l
capacity) and dispose of oil in
compliance with regulations.
4. Mount plug at the bottom of
the pump.
5. Fill pump with fresh oil (see
8.3 for oil type and quantity).
6. Check the oil level (see
6.2.3).

13
MC DE, MC PE, MC PE PLUS
Original Instructions
1. Remove the spark plug cable.
2. Dismantle the cover of the
V-belts.
3. Check the belts for any
damage or missing tension.
4. If required, replace the belts.
5. Mount the cover.
6. Mount the spark plug cable.
6.2.5 Check of V-belts

14
MC DE, MC PE, MC PE PLUS
Original Instructions
7 Troubleshooting
Fault
Pressure drop
Pressure fluctuations
In suction mode
Excess pressure
The motor does not start
Cause
> Air in the system
> High-pressure nozzle
blocked/worn
> Pressure control on the lance
is not set correctly
> Engine speed too low
> Warm/loose belts
> Lack of water
> Pump/accessories partially
frozen
> Water inlet hose is too long or
its cross-section too small
> Lack of water caused by
blocked water filter
> Warm/loose belts
> Lack of water because max.
permissible suction height
has not been heeded
> Water too hot
> Pump draws in air (only
possible in suction mode)
> Engine’s throttle control is
defective (accessory)
> Low fuel level
> Low oil level in engine
> The pump is blocked or
frozen
Remedy
• Vent the system by operating
the spray gun several
times at short intervals. If
necessary, dismount the
lance (see section 4.2.2).
• Clean/replace the high-
pressure nozzle.
• Set the required working
pressure.
• Contact Nilfisk Service
Department.
• Contact Nilfisk Service
Department.
• Open the tap.
• Thaw machine and
accessories.
• Use prescribed size of water
inlet hose.
• Clean the water filter in the
water connection (never
operate the machine without
water filter mounted!)
• Contact Nilfisk Service
Department.
• See chapter 4.2.2.
• See chapter 4.2.2.
• Check that the suction set is
air-tight. Repeat aeration.
• Give less gas/contact Nilfisk
Service Department.
• Open fuel cock/fill with fuel.
• Fill with oil.
• Thaw machine/contact Nilfisk
Service Department.

15
MC DE, MC PE, MC PE PLUS
Original Instructions
• Fill with oil.
• Fill with oil
• Clean.
• Fill the detergent tank.
• Adjust the lance to low
pressure.
> Low oil level in engine
> Low oil level in pump(does
not apply to MC 2C-180/700
PE)
> Injector is dirty or suction
hose is blocked
> Detergent tank is empty
> The lance is not set to low
pressure
The motor stops
When a detergent injector is
used
Fault Cause Remedy
8 Further information
8.1 Recycling the pressure
washer
If the pressure washer is
discarded, make it unusable
immediately
1. Dismount the ignition plug.
The pressure washer contains
valuable materials that should
be recycled. Contact your local
waste disposal site. If you have
any queries, please contact
your local authorities or your
nearest dealer.
8.2 Guarantee Your Nilfisk product is
guaranteed for 12 months from
date of purchase (purchase
receipt must be presented) on
the following conditions:
• that defects are attributable
to flaws or defects in
materials or workmanship.
(Usual wear and tear as well
as misuse are not covered
by the guarantee).
• that repairs have not been
carried out or attempted by
other than Nilfisk-trained
service staff.
• that only original
accessories have been
applied.
• that the product has not
been exposed to abuse such
as knocks, bumps or frost.
• that the instructions in the
manual have been carefully
observed.
A warranty repair comprises the
replacement of defective parts,
but it does not cover freight and
packaging charges. Besides we
refer to national Sale of Goods
Act.
Any illegitimate guarantee
repair will be invoiced. (I.e.
malfunctions due to causes
mentioned in section “7
Trouble shooting” of the
instruction manual).

16
MC DE, MC PE, MC PE PLUS
Original Instructions
8.3 Technical data
MC 2C-
180/700 PE
MC 3C-
165/810 PE
MC 5M-
240/870 PE
MC 5M-
225/910 PE
PLUS
MC 5M-
250/1000 PE
MC 5M-
250/1050 PE
PLUS
MC 7P-
220/1120 PE
PLUS
MC 5M-
195/1000 DE
Working pressure bar 180 165 240 225 250 250 220 195 Water flow (max) l/h 700 810 870 910 1000 1050 1120 1000 Water flow Q IEC l/h 650 750 800 840 930 1000 1010 950 Max. water inlet tem- perature °C 60 60 60 60 60 60 60 70 Min./max. water inlet pressure bar 1/10 1/10 1/10 1/10 1/10 1/10 1/10 1/10 Dimensions (LxWxH) mm 762 x
546 x 603
762 x
546 x 603
1041 x 546 x
635
1067 x 686 x
660
1041 x 546 x
635
1067 x 686 x
660
800 x 690 x
810
800 x 565 x
1010
Noise power level, LWA dB(A) 95.1 93.2 91 90.8 93.2 93.4 91.9 105 Thrust N 31.1 31.9 42.3 42.9 51.8 54.4 52.7 45 Suction height, primed (at max. 8°C) m 1.0 1.0 2.5 2.5 2.5 2.5 2.5 1.0 Oil quantity in pump/ gear l - - 0.5 0.4 0.5 0.5 1.1 0.56/0.27 Oil quantity in motor l 0.5 1 1 11111.65 Oil type (motor/gear) SAE 15-40 Oil type (pump) SAE 15-40 Castrol Al-
phasyn 150 SAE 15-40
Vibrations < 2,5 m/s2
We reserve the right to make alterations.

17
MC DE, MC PE, MC PE PLUS
Original Instructions
8.4 EC Declaration of Conformity
We,
Nilfisk A/S
Kornmarksvej 1
DK-2605 Broendby
DENMARK
Hereby solely declare, that the product:
Product Description Type
HPW - Professional - Mobile Petrol - diesel driven
MC 5M *.* DE, PE, PE PLUS
MC 2C */* PE
MC 3C */* PE
MC 7P */* PE PLUS
Is in compliance with the following standards:
Id and Version Title
EN 60335-1:2012+A11:2014 Household and similar electrical appliances - Safety - Part 1:
General requirements
EN 60335-2-79:2012 Household and similar electrical appliances - Safety - Part
2-79: Particular requirements for high pressure cleaners and
steam cleaners
EN 61000-6-1:2007 Electromagnetic compatibility (EMC) - Part 6-1: Generic stand-
ards - Immunity for residential, commercial and light-industrial
environments
EN 55012:2007+A1:2009 Vehicles, boats and internal combustion engines - Radio
disturbance characteristics - Limits and methods of measure-
ment for the protection of off-board receivers
EN 50581:2012 Technical documentation for the assessment of electrical and
electronic products with respect to restriction of hazardous
substances
Following the provisions of:
Machinery Directive 2006/42/EC
EMC Directive 2004/108/EC
RoHS Directive 2011/65/EC
Noise Emission Directive 2000/14/EC – Conformity assessment procedure according to Annex V.
- Measured noise level: 77-92 dB(A)
- Guaranteed noise level: 90-105 dB(A)
Hadsund 09-09-2015 Anton Soerensen
Senior Vice President – Global R&D
Place Date Name, Title Signature

HEAD QUARTER
DENMARK
Nilfisk A/S
Kornmarksvej 1
DK-2605 Brøndby
Tel.: [phone]
www.nilfisk.com
SALES COMPANIES
ARGENTINA
Nilfisk srl.
Edificio Central Park
Herrera 1855, 6th floor/604
Ciudad de Buenos Aires
Tel.: [phone]
www.nilfisk.com.ar
AUSTRALIA
Nilfisk Pty Ltd
Unit 1/13 Bessemer Street
Blacktown NSW 2148
Tel.: [phone]
www.nilfisk.com.au
AUSTRIA
Nilfisk GmbH
Metzgerstrasse 68
5101 Bergheim bei Salzburg
Tel.: [phone]
www.nilfisk.at
BELGIUM
Nilfisk n.v-s.a.
Riverside Business Park
Boulevard Internationalelaan 55
Bâtiment C3/C4 Gebouw
Bruxelles 1070
Tel.: [phone]
www.nilfisk.be
BRAZIL
Nilfisk do Brasil
Av. Eng. Luis Carlos Berrini, 550
40 Andar, Sala 03
SP - 04571-000 Sao Paulo
Tel.: [phone]
www.nilfisk.com.br
CANADA
Nilfisk Canada Company
240 Superior Boulevard
Mississauga, Ontario L5T 2L2
Tel.: [phone]
www.nilfisk.ca
CHILE
Nilfisk S.A. (Comercial KCS Ltda)
Salar de Llamara 822
8320000 Santiago
Tel.: [phone]
www.nilfisk.cl
CHINA
Nilfisk
4189 Yindu Road
Xinzhuang Industrial Park
201108 Shanghai
Tel.: [phone]
www.nilfisk.cn
CZECH REPUBLIC
Nilfisk s.r.o.
VGP Park Horní Počernice
Do Čertous 1/2658
193 00 Praha 9
Tel.: [phone]
www.nilfisk.cz
DENMARK
Nilfisk Danmark A/S
Industrivej 1
Hadsund, DK-9560
Tel.: [phone]
www.nilfisk.dk
FINLAND
Nilfisk Oy Ab
Koskelontie 23 E
02920 Espoo
Tel.: [phone]
www.nilfisk.fi
FRANCE
Nilfisk SAS
26 Avenue de la Baltique
Villebon sur Yvette
91978 Courtabouef Cedex
Tel.: [phone]
www.nilfisk.fr
GERMANY
Nilfisk GmbH
Guido-Oberdorfer-Straße 2-10
89287 Bellenberg
Tel.: (+49) (0)7306/72-444
www.nilfisk.de
GREECE
Nilfisk A.E.
Αναπαύσεως 29
Κορωπί Τ.Κ. 194 00
Tel.: [phone]
www.nilfisk.gr
HOLLAND
Nilfisk B.V.
Versterkerstraat 5
1322 AN Almere
Tel.: [phone]
www.nilfisk.nl
HONG KONG
Nilfisk Ltd.
2001 HK Worsted Mills
Industrial Building
31-39, Wo Tong Tsui St.
Kwai Chung, N.T.
Tel.: [phone]
www.nilfisk.com
HUNGARY
Nilfisk Kft.
II. Rákóczi Ferenc út 10
2310 Szigetszentmiklós-Lakihegy
Tel.: [phone]
www.nilfisk.hu
INDIA
Nilfisk India Limited
Pramukh Plaza, ‘B’ Wing, 4th floor, Unit
No. 403
Cardinal Gracious Road, Chakala
Andheri (East) Mumbai 400 099
Tel.: [phone]
www.nilfisk.in
IRELAND
Nilfisk
1 Stokes Place
St. Stephen’s Green
Dublin 2
Tel.: [phone]
www.nilfisk.ie
ITALY
Nilfisk SpA
Strada Comunale della Braglia, 18
26862 Guardamiglio (LO)
Tel.: (+39) (0) 377 414021
www.nilfisk.it
JAPAN
Nilfisk Inc.
1-6-6 Kita-shinyokohama, Kouhoku-ku
Yokohama, 223-0059
Tel.: [phone]
www.nilfisk.com
MALAYSIA
Nilfisk Sdn Bhd
Sd 33, Jalan KIP 10
Taman Perindustrian KIP
Sri Damansara
52200 Kuala Lumpur
Tel.: [phone]
www.nilfisk.com
MEXICO
Nilfisk de Mexico, S. de R.L. de C.V.
Pirineos #515 Int.
60-70 Microparque
Industrial WSantiago
76120 Queretaro
Tel.: (+52) (442) 427 77 00
www.nilfisk.com
NEW ZEALAND
Nilfisk Limited
Danish House
6 Rockridge Avenue
Penrose, Auckland 1061
Tel.: [phone]
www.nilfisk.com.au
NORWAY
Nilfisk AS
Bjørnerudveien 24
1266 Oslo
Tel.: [phone]
www.nilfisk.no
PERU
Nilfisk S.A.C.
Calle Boulevard 162, Of. 703, Lima 33-
Perú
Lima
Tel.: [phone]
www.nilfisk.com
POLAND
Nilfisk Sp. Z.O.O.
Millenium Logistic Park
ul. 3 Maja 8, Bud. B4
05-800 Pruszków
Tel.: [phone]
www.nilfisk.pl
PORTUGAL
Nilfisk Lda.
Sintra Business Park
Zona Industrial Da Abrunheira
Edificio 1, 1° A
P2710-089 Sintra
Tel.: [phone]
www.nilfisk.pt
RUSSIA
Nilfisk LLC
Vyatskaya str. 27, bld. 7/1st
127015 Moscow
Tel.: [phone]
www.nilfisk.ru
SINGAPORE
Den-Sin
22 Tuas Avenue 2
639453 Singapore
Tel.: [phone]
www.densin.com
SLOVAKIA
Nilfisk s.r.o.
Bancíkovej 1/A
SK-821 03 Bratislava
Tel.: [phone]
www.nilfisk.sk
SOUTH AFRICA
WAP South Africa
12 Newton Street
Spartan 1630
Tel.: [phone]
www.wap.com.za
SOUTH KOREA
Nilfisk Korea
3F Duksoo B/D, 317-15
Sungsoo-Dong 2Ga
Sungdong-Gu, Seoul
Tel.: [phone]
www.nilfisk.co.kr
SPAIN
Nilfisk S.A.
Torre d’Ara,
Passeig del Rengle, 5 Plta. 10a
08302 Mataró
Tel.: [phone]
www.nilfisk.es
SWEDEN
Nilfisk AB
Taljegårdsgatan 4
431 53 Mölndal
Tel.: [phone]
www.nilfisk.se
SWITZERLAND
Nilfisk AG
Ringstrasse 19
Kircheberg/Industri Stelz
9500 Wil
Tel.: [phone]
www.nilfisk.ch
TAIWAN
Nilfisk Ltd
Taiwan Branch (H.K)
No. 5, Wan Fang Road
Taipei
Tel.: [phone]
www.nilfisk.tw
THAILAND
Nilfisk Co. Ltd.
89 Soi Chokechai-Ruammitr
Viphavadee-Rangsit Road
Ladyao, Jatuchak, Bangkok 10900
Tel.: [phone]
www.nilfisk.co.th
TURKEY
Nilfisk A.S.
Serifali Mh. Bayraktar Bulv. Sehit Sk. No:7
Ümraniye, 34775 Istanbul
Tel.: [phone]
www.nilfisk.com.tr
UNITED ARAB EMIRATES
Nilfisk Middle East Branch
SAIF-Zone
P.O. Box 122298
Sharjah
Tel.: (+971) (0) 655-78813
www.nilfisk.com
UNITED KINGDOM
Nilfisk Ltd.
Nilfisk House, Bowerbank Way
Gilwilly Industrial Estate, Penrith
Cumbria CA11 9BQ
Tel: (+44) (0) 1768 868995
www.nilfisk.co.uk
UNITED STATES
Nilfisk Inc.
14600 21st Avenue North
Plymouth, MN-55447
Tel.: [phone]
www.nilfisk.com
VIETNAM
Nilfisk Vietnam
No. 51 Doc Ngu Str.
P. Vinh Phúc, Q.Ba Dinh
Hanoi
Tel.: [phone]
www.nilfisk.com