Njoy UPCMCOP130HBAAZ01B User manual

Balder Series User Manual
Manual de ulizare
UPCMCOP110HBAAZ01B
UPCMCOP120HBAAZ01B
PWUP-OL150BA-AZ01B
PWUP-OL300BA-AZ01B
UPCMCOP130HBAAZ01B
Before using this product, carefully read all product documentaon and retain it for future reference.
141.12.22.0

02
Package contents
1
The following models belong to the Balder Series:
1000 VA
1500 VA
2000 VA
3000 VA
Balder 1000
Balder 1500
Balder 2000
Balder 3000
UPS unit
Power cord
USB cable
Rack mounng holders
Tower mounng stand
Screws
User manual
Warranty card
Thank you for purchasing our products!
Please read this manual before using the product.
nJoy is a brand of power and backup protecon products that
create soluons for mulple levels of environment complexity,
residenal to industrial.
This UPS will protect your electronic equipment from physical
damage and will provide emergency baery backup power to
prevent data loss in the event of power problems.

03
English
Română
USB
EPO
OUT
RS232
IN
NETWORK/FAX/MODEM
INTELLIGENT SLOT
PROGRAMMABLE OUTLETS (P1)
OUTPUT
INPUT
10A max.
ON/MUTE SELECT OFF/ENTER
888
INPUT
Vac
Vdc
Hz
888
OUTPUT
Vac
Vdc
Hz
H
M
S
P1
USB
EPO
OUT
RS232 IN
NETWORK/FAX/MODEM
INTELLIGENT
SLOT
PROGRAMMABLE
OUTLETS(P1)
OUTPUT
INPUT
Product overview
2
Front View 1000/1500/2000/3000
LCD panel
Funcon buons
LCD Panel
1. Baery info
2. Load info
3. Backup me info
4. Conguraon and fault info
5. Mute operaon
6. Mode operaon info
7. Programmable outlet info
8. Input and baery voltage info
9. Output info
NOTE!
Before installaon, please inspect the unit. Be sure that nothing inside the
package is damaged. Keep the original package in a safe place for future use.
888
INPUT
Vac
Vdc
Hz
888
OUTPUT
Vac
Vdc
Hz
H
M
S
P1
2
9
3 4 5
76
1
8

04
USB
EPO
OUT
RS232 IN
NETWORK/FAX/MODEM
INTELLIGENT
SLOT
PROGRAMMABLE
OUTLETS(P1)
OUTPUT
OUTPUT
INPUT
USB
EPO
OUT
RS232
IN
NETWORK/FAX/MODEM
INTELLIGENT SLOT
PROGRAMMABLE OUTLETS (P1)
OUTPUT
10A max.
INPUT
USB
EPO
OUT
RS232
IN
NETWORK/FAX/MODEM
INTELLIGENT SLOT
PROGRAMMABLE OUTLETS (P1)
OUTPUT
INPUT
10A max.
Back View
5
5
7
7
1
1
3
3
8
8
4
4
Balder 2000
Balder 1000&1500
8
8
2
2
6
6
9
9
Balder 3000
471
3
5
8 26 9

05
English
Română
1. Programable Output
receptacles: connect to non-
crical mission loads (max 10A)
2. General Output receptacles:
connect to crical mission
loads (max 10A)
3. AC input
4. Network/Fax/Modem surge
protecon
5. USB communicaon port
6. RS-232 communicaon port
7. SNMP intelligent slot
8. Emergency power o funcon
connector (EPO)
9. Connector for baery pack
Please comply with all warnings and operang instrucons in this manual
strictly. Save this manual properly and carefully read the following
instrucons before installing the unit. Do not operate this unit before
reading through all safety informaon and operang instrucons carefully:
Important Safety Warnings
3
Transportaon
• Please transport the UPS system only in the original package to
protect against shock and impact.
Preparaon
• Condensaon may occur if the UPS system is moved directly from
cold to warm environment. The UPS system must be absolutely dry
before being installed. Please allow at least two hours for the UPS
system to acclimate to the environment.
• Do not install the UPS system near water or in moist environments.
• Do not install the UPS system where it would be exposed to direct
sunlight or near heat sources.
• Do not block venlaon holes in the UPS housing.
Installaon
• Do not connect appliances or devices which would overload the UPS
system (e.g. laser printers) to the UPS output sockets.
• Place cables in such a way that no one can step on or trip over them.
• Do not connect domesc appliances such as hair dryers to UPS
output sockets.

06
• The UPS can be operated by any individuals with no previous
experience.
• Connect the UPS system only to an earthed shockproof outlet which
must be easily accessible and close to the UPS system.
• Please use only VDE-tested, CE-marked mains cable (e.g. the mains
cable of your computer) to connect the UPS system to the building
wiring outlet (shockproof outlet).
• Please use only VDE-tested, CE-marked power cables to connect the
loads to the UPS system.
• When installing the equipment, it should ensure that the sum of
the leakage current of the UPS and the connected devices does not
exceed 3.5mA.
Operaon
• Do not disconnect the mains cable on the UPS system or the
building wiring outlet (shockproof socket outlet) during operaons
since this would cancel the protecve earthing of the UPS system
and of all connected loads.
• The UPS system features its own, internal current source (baeries).
The UPS output sockets or output terminals block may be electrically
live even if the UPS system is not connected to the building wiring
outlet.
• In order to fully disconnect the UPS system, rst press the OFF/
Enter buon to disconnect the mains.
• Prevent uids or other foreign objects from entering the inside of the
UPS system.
Maintenance, service and faults
• The UPS system operates with hazardous voltages. Repairs may be
carried out only by qualied maintenance personnel.
• Cauon - risk of electric shock. Even aer the unit is disconnected
from the mains (building wiring outlet), components inside the UPS
system are sll connected to the baery and electrically live and
dangerous.
• Before carrying out any kind of service and/or maintenance,
disconnect the baeries and verify that no current is present and no

07
English
Română
hazardous voltage exists in the terminals of high capability capacitor
such as BUS-capacitors.
• Only persons are adequately familiar with baeries and with the
required precauonary measures may replace baeries and supervise
operaons. Unauthorized persons must be kept well away from the
baeries.
• Cauon - risk of electric shock. The baery circuit is not isolated
from the input voltage. Hazardous voltages may occur between the
baery terminals and the ground. Before touching, please verify that
no voltage is present!
• Baeries may cause electric shock and have a high short-circuit
current. Please take the precauonary measures specied in this
manual and any other measures necessary when working with
baeries: remove wristwatches, rings and other metal objects, use
only tools with insulated grips and handles.
• When changing baeries, install the same number and same type of
baeries.
• Do not aempt to dispose of baeries by burning them. This could
cause baery explosion.
• Do not open or destroy baeries. Escaping electrolyte can cause
injury to the skin and eyes. It may be toxic.
• Please replace the fuse only with the same type and amperage in
order to avoid re hazards.
• Do not dismantle the UPS system.
• WARNING: This is a category C2 UPS product. In a residenal
environment, this product may cause radio interference, in which
case the user may be required to take addional measures. (only for
220/230/240 VAC system).

08
Installaon
4
4.1 Operang principle
The operang principle of the UPS is shown below:
EMI/RFI
Filters
Recer
/PFC Inverter
DC-to-DC
converter
Dynamic
Bypass
Output
Input
Baery
Baery
Charger
The UPS is composed of mains input, EMI/RFI lters, recer/PFC,
inverter, baery charger, DC-to-DC converter, baery, dynamic bypass
and UPS output.
The UPS can protect your equipment from all power problems such as
surges, spikes, blackouts, brownouts and line noise. When AC power is
present and the ON/ Mute switch is turned ON, the UPS will provide
pure and stable AC power to the output. The UPS will also charge the
baery in the on-line mode.

09
English
Română
I. Remove front panel
II. Connect the AC input and re-
connect baery wires.
III. Put the front panel back to
the unit.
4.2 Connecng your equipment and rst usage
The UPS is simple to install and operate. Please read the following steps
before connecng any equipments to this UPS:
Step 1. Connecng the baeries: For safety consideraon, the UPS is
shipped out from factory without connecng the baery wires. To re-
connect baery wires please follow below steps:

10
USB
EPO
OUT
RS232
IN
NETWORK/FAX/MODEM
INTELLIGENT SLOT
PROGRAMMABLE OUTLETS (P1)
OUTPUT
INPUT
10A max.
BATETRY BREAKER
Max, 50A
Step 2. Connect to External Baery Cabinet: When connecng external
baery cabinet, please be sure to connect polarity correctly. Connect
posive pole of baery cabinet to posive pole of external baery
connector in UPS and negave pole of baery cabinet to negave pole
of external baery connector in UPS. Polarity mis-connecon will cause
UPS internal fault.
Connect only compable Balder baery cabinet provided by nJoy. Please
read the manual of the UPS and baery cabinet and set the UPS baery
total capacity in Ah and the charging current accordingly. The use of
another baery cabinet may damage the UPS and void the warranty.
NOTE!
These baery cabinets care compable with the following UPS:
•CA0312GX-AZ (36Vdc): UPS Balder 1000 / 1500
•CA0712GX-AZ (72Vdc): UPS Balder 2000 / 3000

11
English
Română
First x the holders of the rack on the UPS.
A. Rack - mount installaon
B. Tower installaon
Then x the UPS on the rack through the holders
First x the holders to t
the UPS.
Then put the UPS in place.
Step 3. Mounng the UPS: Balder series UPS can be either displayed on
the desk or mounted in the 19” rack chassis. Please choose your favourite
way to posion this UPS.

12
Step 4. UPS input connecon: Plug the UPS into a two-pole, three-wire,
grounded receptacle only. Avoid using extension cords.
Step 5. UPS output connecon: For socket-type outputs there two kinds
of output: programmable outlets and general outlets. Please connect non-
crical devices to the programmable outlets and crical devices to the
general outlets. During power failure, you may extend the backup me
to crical devices by seng shorter backup me for non crical devices.
Step 6. Communicaon connecon: To allow for unaended UPS
shutdown/start-up and status monitoring, connect the communicaon
cable one end to the USB/RS-232 port and the other to the communicaon
port of your PC. With the monitoring soware installed, you can schedule
UPS shutdown/start-up and monitor UPS status through PC. The UPS is
equipped with a slot for either SNMP or AS400 card. When installing either
SNMP or AS400 card in the UPS, it will provide advanced communicaon
and monitoring opons.
Do NOT plug LASER
PRINTERS into any of
the outlets.
Do NOT plug any SURGE
STRIPS into any of the
outlets.
CAUTION
Communication port:
USB Port RS-232 Port Intelligent slot
NOTE!
USB port and RS-232 port can’t work at the same me.

13
English
Română
Step 8. Disable and enable EPO funcon: Keep the pin 1 and pin 2 closed
for UPS normal operaon.
Step 9. Turn on the UPS: Press the ON/Mute buon on the front panel
for two seconds to power on the UPS.
Step 7. Network connecon: Connect a single modem/phone/fax line
into surge-protected “IN” outlet on the back panel of the UPS unit.
Connect from “OUT” outlet to the equipment with another modem/fax/
phone line cable.
Network/Fax/Phone surge port:
It’s in closed status for UPS
normal operaon.
To acvate EPO
funcon, remove
these two screws.
NOTE!
The baery charges fully during the rst ve hours of normal operaon. Do
not expect full baery run capability during this inial charge period.
Step 10. Install soware: For opmal computer system protecon, install
UPS monitoring soware to fully congure UPS shutdown. Use supplied
RS-232 or USB communicaon cable to connect RS-232/USB port of
UPS and RS-232/USB port of PC. Install the UPS monitoring soware
from hps://www.power-soware-download.com/viewpower.html to fully
congure UPS shutdown.

14
Operaons
5
5.1 Buon operaons
ON/MUTE SELECT OFF/ENTER
ON/Mute Buon
• Turn on the UPS: Press and hold ON/Mute buon for at least 2 sec-
onds to turn on the UPS.
• Mute the alarm: Aer the UPS is turned on in baery mode, press
and hold this buon for at least 5 seconds to disable or enable the
alarm system. But it’s not applied to the situaons when warnings or
errors occur.
• Up key: Press this buon to display previous selecon in UPS seng
mode.
• Switch to UPS self-test mode: Press ON/Mute buons simultane-
ously for 5 seconds to enter UPS self-tesng while in AC mode, ECO
mode, or converter mode.
OFF/Enter Buon
• Turn o the UPS: Press and hold this buon for at least 2 seconds
to turn o the UPS. The UPS will be in standby mode under normal
power or transfer to Bypass mode if the Bypass seng is enabled.
• Conrm selecon key: Press this buon to conrm selecon in UPS
sengs mode.
Select Buon
• Switch LCD message: Press this buon to change the LCD message
for input voltage, input frequency, baery voltage, output voltage
and output frequency.
• Sengs mode: Press and hold this buon for 5 seconds to enter
UPS sengs mode when the UPS is in standby mode or bypass
mode.
• Down key: Press this buon to display next selecon in UPS sengs
mode.
ON/Mute + Select Buon
• Switch to bypass mode: When the main power is normal, press ON/

15
English
Română
5.2 LCD Panel Indicators
Display Funcon
Backup me informaon
H
M
S
Indicates the esmated backup me.
H: hours, M: minute, S: second.
Conguraon and fault informaon
Indicates the conguraon items, and the conguraon
items are listed in details in secon 5.5.
Indicates the warning and fault codes, and the codes are
listed in details in secon 5.7 and 5.8.
Mute operaon
Indicates that the UPS alarm is disabled.
Mute and Select buons simultaneously for 5 seconds. Then the
UPS will enter to bypass mode. This acon will be ineecve when
the input voltage is out of acceptable range.
Select + OFF/Enter Buon
• Rack or Tower display switch: Press Select and OFF/Enter buons
simultaneously for 3 seconds. The display change from/to Rack to/
from Tower.
888
INPUT
Vac
Vdc
Hz
888
OUTPUT
Vac
Vdc
Hz
H
M
S
P1

16
Output & Load informaon
888
OUTPUT
Vac
Vdc
Hz
Indicates the output voltage and output frequency.
Vac: AC voltage, Vdc: DC voltage, Hz: frequency
Load informaon
Indicates the load level by 0-24%, 25-49%, 50-74% and
75-100%.
Indicates overload.
Indicates the load or the UPS output is short circuit.
Programmable outlets informaon
P1
Indicates that programmable management outlets are
working.
Mode operaon informaon
Indicates the UPS connects to the mains.
Indicates the baery is working.
Indicates the bypass circuit is working.
Indicates the ECO mode is enabled.
Indicates the AC to DC circuit is working.

17
English
Română
Indicates the inverter circuit is working.
Indicates the output is working.
Baery informaon
Indicates the baery level by 0-24%, 25-49%, 50-74%,
and 75-100%.
Indicates the baery is fault.
Indicates low baery level and low baery voltage.
Input & baery informaon
Indicate the input voltage, input frequency and baery
voltage.
Vac: AC voltage, Vdc: DC voltage, Hz: frequency
Mode Alarm
Baery Mode Sounding every 5 seconds
Low Baery Sounding every 2 seconds
Overload Sounding every second
Fault Connuously sounding
Bypass Mode Sounding every 10 seconds
5.3 Audible Alarm Indicators

18
Abbreviaon Display content Meaning
ENA ENA Enable
DIS d15 Disable
ESC ESC Escape
HLS HLS High loss
LLS LLS Low loss
BAT bAT Baery
BAH bAH Baery AH
CHA CHA Charger current
CBV Cbu Charger boost voltage
CFV CFu Charger oat voltage
EPO EPO EPO
AO AO Acve open
AC AC Acve close
OIT OItOutput isolaon
transformer
EAT EAtEsmated autonomy me
RAT rAtRunning autonomy me
CF CF Converter
5.4 LCD display wordings index

19
English
Română
ON ON ON
SD Sd Shutdown
OI OI Over input current
TP TP Temperature
CH CH Charger
FU FU Bypass frequency
unstable
BR br Baery
Replacement
EE EE EEPROM error
OK 0K OK
BL bL Baery Low
OL OL Over Load
NC NC Baery No Connect
OC OC Over Charge
SF SF Site wiring fault
BF bF Baery Fault
BV bv Bypass Out Range

20
888 888
23
1
There are two parameters to set up the UPS.
• Parameter 1: For program alternaves. Refer to the table below.
• Parameter 2&3: The sengs opons or values for each program.
Interface Sengs
01: Output voltage sengs
230
OUTPUT
Vac
Parameter 2: Output voltage:
200: presents output voltage is 200Vac
208: present output voltage is 208Vac
220: present output voltage is 220Vac
230: present output voltage is 230Vac
240: present output voltage is 240Vac
NOTE: Derate capacity to 80% when the output
voltage is adjusted to 200VAC/208VAC.
02: Frequency Converter enable/disable
CF ENA
Parameter 2: Enable or disable converter
mode.
You may choose the following two opons:
CF ENA: converter mode enable
CF DIS: converter mode disable (Default)
NOTE: Derate capacity to 80% when Frequency
Converter mode is enabled.
5.5 UPS sengs
NOTE!
Most parameters can be set only in bypass/standby mode; please set the UPS
to bypass/standby mode (see secon 5.1) and then change parameters.