Njoy Ranger 30KT User manual

Ranger Series
User Manual
232.21.23.0Before using this product, carefully read all product documentaon and retain it for future reference.
Ranger 30KT - UP33TOP130KRAAZ01B
Ranger 60KT - UP33TOP160KRAAZ01B
Ranger 120KT - UP33TOP112ZRAAZ01B
Ranger 180KT - UP33TOP118ZRAAZ01B

2
Table of contents
1. Safety and EMC instrucons .................................................................................. 5
1-1. Transportaon and storage ...................................................................................... 5
1-2. Preparaon .................................................................................................................. 5
1-3. Installaon .................................................................................................................. 5
1-4. Connecon warnings ................................................................................................ 6
1-5. Operaon ..................................................................................................................... 7
1-6. Standards .................................................................................................................... 7
2. Installaon and operaon ....................................................................................... 8
2-2. Wiring terminal view ...............................................................................................8
2-3. UPS Posioning...........................................................................................................16
3. Operaons ........................................................................................................ 17
3-1. Inial operaon ....................................................................................................... 17
3-2. Screen descripon ................................................................................................... 17
3-2.1. Main screen .................................................................................................... 18
3-2.2. Control screen ................................................................................................. 19
3-2.3. Measure screen ............................................................................................. 22
3-2.4. Seng screen ............................................................................................... 23
3-2.5. Informaon screen ....................................................................................... 31
3-2.6. Data Log screen ............................................................................................... 34
3-3. Audible alarm............................................................................................................ 34
3-4. Single UPS operaon ..............................................................................................35
3-5. Parallel operaon ................................................................................................... 37
3-6. Fault code .................................................................................................................38
3-7. Warning code ........................................................................................................... 40
4. Troubleshoong .................................................................................................. 41
5. Storage and maintenance ....................................................................................43
5-1. Storage ......................................................................................................................... 43
5-2. Maintenance ............................................................................................................... 43

3
This User Manual is compable with the following Ranger Series models:
30K VA
60K VA
120K VA
180K VA
Ranger 30KT
Ranger 60KT
Ranger 120KT
Ranger 180KT
Thank you for purchasing our products!
Please read this manual before using the product.

4
We assume no responsibility or liability for loss or damages, whether direct,
indirect, consequenal or incidental, which might arise out of the use of such
informaon. The use of any such informaon will be enrely at the user’s risk.
Informaon in this manual is subject to change without noce. We make no
commitment to update or keep current the informaon in this manual. If you
nd informaon in this manual that is incorrect, misleading, or incomplete, we
would appreciate your comments and suggesons.
Please comply with all warnings and operang instrucons in this manual.
This equipment should only be installed, serviced, and maintained by
qualied personnel. If you are the beneciary of this UPS and you encounter
any problem with it, please contact authorized personel who installed the
UPS. Do not operate this unit before reading through all safety informaon
and operang instrucons carefully.
DANGER!
This UPS carries lethal voltages. Installaon, maintenance, service and repairs
must be performed by authorized personnel only. There are no user-serviceable
parts inside the UPS. Do not aempt to modify any sengs of the UPS unless
you are a trained technician. If you need to change any sengs of this UPS or
you have technical warnings or faults shown on UPS screen, please contact the
technician that installed the UPS.
WARNING

5
Safety and EMC instructions1
All safety instrucons in this document must be read, understood and
followed.
1.1. Transportaon and storage
• Please transport the UPS system only in the original packaging to protect
against shock and damage.
• The UPS must be stored in the room where the temperature is well
regulated. Ambient temperature should not exceed 40°C.
1.2. Preparaon
• Condensaon may form if the UPS system is moved from cold to warm
environment immediately.
• The UPS system must be absolutely dry before being installed.
Please allow at least two hours for the UPS system to acclimate with the
environment.
• Do not install the UPS system near water or in moist environments.
• Do not install the UPS system where it would be exposed to direct
sunlight or near by heat source.
• Do not block venlaon holes on the UPS housing.
1.3. Installaon
• Do not connect appliances or devices which would overload the UPS (e.g.
big motor type equipment) to the UPS output terminal.
• Place cables in such a way that no one can step on or trip over them.
• Do not block air vents on the housing of the UPS. Ensure proper unit
spacing of venlaon.
• UPS equipped with grounding terminal, in the nal installaon phase,
connect grounding/earthing wire to the external UPS baery cabinets or
appropriate grounding terminals
• The UPS can be installed only by qualied maintenance personnel.
• An appropriate disconnect device such as short circuit backup protecon
should be incorporated during installaon.
• An integral emergency shuto switch which prevents addional load
from the UPS in any mode of operaon should be implemented during the
installaon.
• Secure the grounding/earthing wire before connecng to any live wire
terminal.
• Installaon and Wiring must be in accordance with the local electrical
laws and regulaons.

6
1.4. Connecon warnings
• There is no standard backfeed protection inside of the UPS. However,
there are relays on the Input to cut off line voltage while the neutral is still
connect to UPS.
UPS
Main
Input
Input Rly
Input Rly
N
L1
L2
L3
Bypass
Input
N
L1
L2
L3
UPS
Main
Input
Input Rly
Input Rly
L1
L2
L3
N
Bypass
Input
Input Rly
L1
N
UPS
Main
Input
Input Rly
L1
Bypass
Input
N
Input Rly
L1
N
3:3 phase 3:1 phase 1:1 phase
• This UPS should be connected with TN grounding/earthing system.
• The power input for this unit must be three-phase rated in accordance
with the equipment nameplate. It also must be suitably grounded.
High leakage current!
Earth connecon essenal before connecng supply!
WARNING
• Use of this equipment in medical instrument of any life-sustaining
equipment where failure of this equipment can reasonably be expected to
cause the failure of the life-sustaining equipment or to significantly affect its
safety or effectiveness is not recommended. Do not use this equipment in
the presence of a flammable mixture with air, oxygen or nitrous oxide.
• Connect grounding terminal of UPS to a grounding electrode conductor.
• In accordance with safety standard EN-IEC 62040-1, installation has to
be provided with a «Backfeed Protection»system, as for example a contactor,
which will prevent the appearance of voltage or dangerous energy in the input
mains during a mains fault (respect the wiring diagram of «Backfeed Protection»
depending if the equipment is with signal or three phase input).
NOTE!
There can be no derivation in the line that goes from the «Backfeed Protection» to
the UPS, as the standard safety would be infringed.
• Warning labels should be placed on all primary power switches installed
in places away from the unit to alert the electrical maintenance personnel of
the presence of a UPS in the circuit. The label will bear the following or an
equivalent text:

7
Before working on this circuit
1. Isolate Uninterruptible Power Supply (UPS)
2. Then check for Hazardous Voltage between all terminals including the
protected earth.
Risk of Voltage Backfeed
1.5. Operaon
• Do not disconnect the grounding/earthing conductor cable on the UPS or
the building wiring terminals under any circumstance.
• The UPS system features its own, internal current source (batteries). The
UPS output sockets or output terminal blocks may be electrically live even if
the UPS system is not connected to the building mains/live wires .
• In order to fully disconnect the UPS system, first press the “OFF” button
and then disconnect the mains/live wires .
• Ensure that no liquid or other foreign objects can enter into the UPS
system.
1.6. Standards
*Safety
IEC/EN 62040-1
*EMI
Conducted Emission IEC/EN 62040-2 Category C3
Radiated Emission IEC/EN 62040-2 Category C3
*EMS
ESD IEC/EN 61000-4-2 Level 4
RS IEC/EN 61000-4-3 Level 3
EFT IEC/EN 61000-4-4 Level 4
SURGE IEC/EN 61000-4-5 Level 4
CS IEC/EN 61000-4-6 Level 3
Power-frequency Magnec eld IEC/EN 61000-4-8 Level 4
Low Frequency Signals IEC/EN 61000-2-2
This is a product for commercial and industrial applicaon and the
second environment installaon restricons or addional measures may
be needed to prevent disturbances.
WARNING

8
2.1. Wiring terminal view
2.1.1 Ranger 30KT (UP33TOP130KRAAZ01B)
1RS-232 communication port
2USB communication port
3 Emergency power off function connector (EPO connector)
4 Share current port (only available for parallel model)
5 Parallel port (only available for parallel model)
6Intelligent slot
7 External battery connector/terminal
8 Line input circuit breaker/switch
9 Maintenance bypass switch (option)
10 Grounding terminal
11 Line input terminal
12 Output terminal
13 Bypass input terminal
14 Output switch
15 Bypass input circuit breaker/switch
2Installation and operation
NOTE!
Before installation, check the product. Make sure there is no physical damage. Do
not switch on the device and inform the transporter and distributor immediately
if you find any damage or missing components or accessories. Keep the original
packaging for future use. It is recommended to keep each piece of equipment
and batteries in their original packaging as they have been designed to provide
maximum protection during transport and storage.

9
Diagram 1: Ranger 30KT
rear panel

10
2.1.2 Ranger 60KT (UP33TOP160KRAAZ01B)
1RS-232 communication port
2USB communication port
3 Emergency power off function connector (EPO connector)
4Share current port
5Parallel port
6Intelligent slot
7 External battery connector/terminal
8 Line input circuit breaker/switch
9 Maintenance bypass switch
10 Input/Output terminal (Refer to diagram 2 and 3 for details)
11 Line input terminal
12 Output terminal
13 Input grounding terminal
14 Output grounding terminal
15 Bypass input circuit breaker/switch
16 Bypass input terminal
17 Output switch

11
Diagram 2: Ranger 60KT
rear panel
Diagram 3: Ranger 60KT
input/output terminal

12
2.1.3 Ranger 120KT (UP33TOP112ZRAAZ01B)
1RS-232 communication port
2USB communication port
3 Emergency power off function connector (EPO connector)
4Share current port
5Parallel port
6Intelligent slot
7 External battery connector/terminal
8 Line input circuit breaker/switch
9 Maintenance bypass switch
10 Bypass input terminal (Refer to diagram 4 and 5 for details)
11 Line input terminal (Refer to diagram 4 and 5 for details)
12 Output terminal (Refer to diagram 4 and 5 for details)
13 Cold start function button
14 Dry contact communication port
15 Bypass input circuit breaker/switch
16 Output switch

13
Diagram 4: Ranger 120KT
Front panel
Diagram 5: Ranger 120KT
Terminal view

14
2.1.4 Ranger 180KT (UP33TOP118ZRAAZ01B)
1RS-232 communication port
2USB communication port
3 Emergency power off function connector (EPO connector)
4 Share current port (only available for parallel model)
5 Parallel port (only available for parallel model)
6Intelligent slot
7 External battery connector/terminal
8 Line input circuit breaker/switch
9 Maintenance bypass switch (option)
10 Bypass input terminal (Refer to diagram 6 and 7 for details)
11 Line input terminal (Refer to diagram 6 and 7 for details)
12 Output terminal (Refer to diagram 6 and 7 for details)
13 Cold start function button
14 Dry contact communication port
15 Bypass input circuit breaker/switch
16 Output switch

15
Diagram 6: Ranger 180KT
Front panel
Diagram 7: Ranger 180KT
Terminal view

16
2.2. UPS Posioning
The UPS should be installed in the environment with free ventilation, less
dust, optimum ambient temperature and humidity.
The recommended ambient temperature is 20°C~25°C with 50% humidity.
•Ambient temperature: 0°C~+40°C
• Storage temperature: -15ºC ~ 60ºC
• Relative humidity: 0 ~ 95%
• Altitude: If the UPS is installed within 1000m, the UPS power will not be
derated. When the altitude is over 1000m, the output power will be derated
by following the table.
• Vertical: No vibration and the degree of deviation from vertical shouldn’t
be more than 5°.
• Space: It’s requested to have a clearance of approx. 50 cm to the front
and back of the unit and approx. 50 cm to the side.
Cauon!
It’s NOT allow to have flammable, explosive or corrosive gas or liquid in
installation environment. It is forbidden to install in a metal conductive dust
environment.
2.3. Soware installaon
You can monitor the UPS via USB port by installing ViewPower software from
https://www.power-software-download.com/viewpower.html.
Altude (m) 1000 1500 2000 2500 3000 3500 4000 4500 5000
Coecient 100% 95% 91% 86% 82% 78% 74% 70% 67%

17
Operations
3
3.1. Inial operaon
Step 1. Before operation, make sure that the two strings of batteries
are connected correctly in order of ”+,GND,-” terminals and the breaker
of the battery pack is at “ON” position (only in case of external battery packs
presence).
Step 2. Press the POWER button to set up the power supply for the
UPS. UPS will enter to power on mode. After initialization, UPS will enter to
“No Output mode”.
3.2. Screen descripon
After initialization, the LCD will display main screen.
There are five sub-menus: Control, Measure, Setting, Information and Data log.
Touch any sub-menu icon to enter into the sub-screen.
Main
Control
Measure
Setting
Info
Data Log
ON/OFF UPS
ON/OFF charger
Exit Parallel
Battery test
Mute all
Measure 1
Measure 2
Measure 3
General
Advance
Basic info
Rated info
Parameter info

18
NOTE!
Setting/Advanced Menu is not detailed in this User Manual.. If you need
assistance or have any warning or fault codes on your UPS screen, please contact
the technician that installed the UPS.
DO NOT attempt to modify any settings of the UPS unless you are a trained
technician. This UPS carries lethal voltages. All repairs and service must be
performed by authorized personnel only.
3.2.1. Main screen
Upon powering on, the LCD will start initialization process that takes a few
seconds.
After initialization, the main screen will display as shown below. On the
bottom, there are five icons to represent five sub-menus: CONTROL,
MEASURE, SETTING, INFO, DATALOG.
Main screen

19
3.2.2. Control screen
Touch the icon to enter control sub-menu.
Control screen
Touch the icon to return back to main screen no matter it’s in any screen
of any submenu.
ON/OFF UPS
It will show “Turn on UPS?” when UPS is off.
It will show “Turn off UPS?” when UPS is on.
Touch “YES” to turn on or off the UPS. Then, the screen will return to main
screen.
Touch “Back” to return to main screen immediately or “No” to cancel this
operation and back to main screen.
Turn on UPS Turn o UPS

20
Baery test
It will show “Battery Test” if the UPS is not in test. Touch “Yes” to start
battery test. Then, it will show “Battery testing..…” during battery test period.
After few seconds, battery test result will show on the screen. Touch “Back”
to return to main screen immediately or “No” to cancel this operation and
back to main screen. It will show “Cancel battery test” if the UPS is in test.
Baery Test Cancel Baery Test
Audio mute
It will show “Mute all” if the audio is active. Touch “Yes” to activate mute. If
“Mute all” is active, it will show icon on the top left corner of the main
screen. Touch “Back” to return to CONTROL screen immediately or “No” to
cancel this operation and back to CONTROL screen.
It will show “Cancel Mute All” if the UPS is mute already. Touch “Yes” activate
audio function or “No” to keep mute. Touch “Back” to return to CONTROL
screen.
Mute All Cancel Mute All