Noble House Home Furnishings BAR CABINET User manual

Page 1 of 8Page 1 of 8
Assembly Instructions
Caution : You must read this before you proceed.
BAR CABINET
CAUTION : This PRODUCT is NOT a TOY.
Keep your child / children at bay during the assembly process.
For turning/lifting the Bar Table and to prevent damage to the Bar
Table, three adults are required.Table, three adults are required.
Noble House Home Furnishings LLC
Please look in the Bottle Holder for hardware packs

Page 2 of 8Page 2 of 8
NO. Picture QTY
Assembly Preparation
Before Beginning Assembly:
Parts List
Description
NO. Picture QTY
A 1
B 1
C 1
D 1
E 2
F 2
G 1
Front Panel
Right Side Panel
Left Side Panel
Description
Table Top
Shelf
Support bar
Base Stand
H 1
Bottle Holder
Noble House Home Furnishings LLC

Page 3 of 8Page 3 of 8
I 5
K 11
L 7
Hard ware
Long Screws (M6x90mm)
Assembly Step
Medium Screws (M6x50mm)
Short Screws (M6x25mm)
Unpack and place all parts on a clean, non-marring surface.
Place the Base Stand(G),right side up.
Align and insert Front Panel(B) into Base Stand(G) by inclining the corner, as
pictured above.
Then, gently slide the entire Front Panel(B) into this slot housing.
CAUTION: This panel must be held in position whilst the SIDE PANELs are being
attached.
Noble House Home Furnishings LLC
M 1
Allen Wrench

Page 4 of 8Page 4 of 8
Pic. 1 Pic. 2
Step 4
Noble House Home Furnishings LLC
Align and insert Left Side Panel(C), Right Side Panel(D) into Base Stand(G) with Tenons on the
Side Panels snugly fitting into the Mortises in Base Stand(C) as picture 1.
Align the Mounting Positions of the Left Side Panel(C) with those on the Front Panel(B).
Insert Medium Screws(K) through the Mounting Positions and affix using Allen Wrench(M) and
slightly tighten the Screws as picture 2.
Repeat the same process with the Right Side Panel(D).
DO NOT over tighten the Screws.
Align and insert Support Bars(F) into Left Side Panel(C) with Tenons on the bars snugly fitting into
the Mortises in Left Side Panel(C).
Insert Medium Screws(K) through the Mounting Positions and affix using Allen Wrench(M).
Repeat the same process with the Right Side Panel(D).
DO NOT over tighten the Screws.
Each screw is to be driven in sequentially.

Page 5 of 8Page 5 of 8
Step 5
Step 6
Pic. 3
Noble House Home Furnishings LLC
Place the Cabinet as shown in the above picture.
Align and insert the Long Screws(I) through the Mounting Positions and affix to Base Stand(G) by
using Allen Wrench(M).
Carefully stand the Cabinet up.
Put the Table Top(A) onto the Cabinet.
Push Table Top(A) forward until the Mounting Positions are aligned.
To affix the Table Top(A) insert the Short Screws(L) through the Mounting Positions of the Cabinet
and Table Top(A) with Allen Wrench(M).
The Bolt connecting points are found on the inside of the Cabinet as indicated in Pix.3 marked by
the "L" position.
DO NOT over tighten the Screws.

Page 6 of 8Page 6 of 8
Step 7 E
Prefitted Dowel at prefitted support bar
Align and insert the Shelves(E) with Mounting Position: prefitted Dowel at prefitted
ssuuppppoorrtt bbaarrss oonn tthhee ssiiddee ooff tthhee CCaabbiinneett..
Step 8
Noble House Home Furnishings LLC
Align and insert the Bottle Holder(H) on the Base Stand(G).
Insert the Short Screws(L) through the mounting position and affix the Tray(H)
by using Allen Wrench(M).

Page 7 of 8Page 7 of 8
Step 9
Proceed to fully tighten all Screws, in a sequential manner.
Ensure that all Screws are securely tightened.
Your Bar Cabinet is ready for use.
Noble House Home Furnishings LLC