Noble House Home Furnishings ROCKING CHAIR User manual

Assembly Instructions
Caution: You must read this Assembly Instructions before you proceed
Rocking Chair
Caution: This Rocking Chair is NOT a TOY.
Keep your child / children at bay in the process of assembly.
For turning the Rocking Chair and to prevent damage to the Rocking Chair,
two persons may be needed to execute this action.
Please look in the leg panel for hardware packs.
Noble House Home Furnishings LLC
Page 1 of 10

Label Picture Description QTY
ABackrest Panel 1
BSeat Panel 1
1
DRight Leg Panel 1
ESeat Cushion 1
Label Picture Description QTY
①
Screw
(M6*80mm) 5
②
Screw
(M6*70mm) 5
③
Allen Wrench 1
Hardware
Parts List
Noble House Home Furnishings LLC
Page 2 of 10
Left Leg Panel
C
Front

Before Beginning Assembly:
Assembly Preparation
x5
x5
x1
Noble House Home Furnishings LLC
Page 3 of 10
Front

Assembly Steps
Overview
This Rocking Chair has multiple parts and may require up to 30 minutes to
assemble. To give you an overview of the Rocking chair parts, the above picture is
to help you put the various parts into perspective. Please read through the
instructions below to familiarise yourself with the parts and steps before assembly.
Right Leg
Panel (D)
Backrest
Panel (A)
Left Leg
Panel (C)
Seat Panel
(B)
FRONT FACING
Seat Cushion
(E)
Noble House Home Furnishings LLC
Page 4 of 10

Step 2
With the help from your assistant, place the Seat Panel (B) with its one side facing
upwards, vertically onto a clean, soft surface to avoid any scratches or damages to
the product as picture shown above.
Align the tenon of the Seat Panel (B) into the mortise of the Right Leg Panel (D) as
shown above. Then, affix the Seat Panel (B) to Right Leg Panel (D) using Screws
(
①
) and the Allen Wrench (
③
).
DO NOT FULLY TIGHTHEN THE SCREWS.
Step 1
Unpack and place all parts on a clean, non-marring surface.
B
①
③
D
Noble House Home Furnishings LLC
Page 5 of 10
Front
Front

Step 3
With the help from your partner, turn the Right Leg Panel (D) of the assembled part
in step 2 down to the ground.
Attach the Left Leg Panel (C) to the assembled part of step 2 by aligning the tenon
of the Seat Panel (B) into the Mortise of Left Leg Panel (C) as shown above.
Then, affix the Seat Panel (B) to the Left Leg Panel (C) using Screws (
①
) and the
Allen Wrench (
③
).
DO NOT FULLY TIGHTHEN THE SCREWS.
D
C
B
①
③
Noble House Home Furnishings LLC
Page 6 of 10
Front

With the help from your partner, turn the assembled part in step 3 right side up.
Attach the Backrest Panel (A) to the Right Leg Panel (D) and Left Leg Panel (C),
using Screws (
②
) and the Allen Wrench (
③
)
DO NOT FULLY TIGHTHEN SCREWS.
Step 4
②
A
D
C
B
③
②
③
Noble House Home Furnishings LLC
Page 7 of 10

Step 6
E
Noble House Home Furnishings LLC
Page 8 of 10
Place the Seat Cushion (E) onto the Rocking Chair.
Connect the Seat Cushion (E) to the Seat Panel (B) by using Magic Tape
as shown above

Step 5
Place the Rocking Chair on a LEVEL SURFACE.
Inspect the Rocking Chair and make sure all parts are connected.
Gently and gracefully, sit into to the Rocking Chair.
This would help to align all the parts at all the joint areas.
Then get out of the Rocking Chair and in a sequential manner, proceed to tighten all
Screws. Whenever moving or lifting the Rocking Chair be sure to secure assistance
from your adult partner(s).
When tightening any Screws, tighten sequentially.
DO NOT tighten any Screw fully and then move on towards the next one.
If there are still wobbles after tightening, loosen the Bolts and Screws and execute
this same process.
WARNING!! IF Rocking Chair IS NOT STABLE , IT COULD LEAD TO DAMAGING
THE PRODUCT.
Ensure all screws are fully locked into position.
Your Rocking Chair is ready for use.
This Rocking Chair can only be only be used on a flat, lever surface.
Noble House Home Furnishings LLC
Page 9 of 10

Noble House Home Furnishings LLC
Page 10 of 10