Noble House Home Furnishings Headboard User manual

Noble House Home Furnishings LLC
Page 1 OF 9
Headboard
WARNING!!
Furniture Tipping Risk.
Serious risk of severe or fatal crush injuries can occur from
furniture tipping over if not secured.
Children like to climb on furniture and Unsecured furniture can
pose a serious danger.
Please follow all instructions and install the tip-over restraints
provided.
Assembly Instructions
Caution : You must read this before you proceed. This Headboard must
be used in conjunction with a Mattress Support Frame (not included and
not supplied with this headboard).

Noble House Home Furnishings LLC
Page 2 OF 9
Label Picture Description Qty
AHeadboard 1
B
Left Support Leg with 3
Mounting Brackets
(Labelled "Left" on the
bottom)
1
C
Right Support Leg with 3
Mounting Brackets
(Labelled "Right" on the
bottom)
1
Label Picture Description Qty
aBolt (M8x25mm) 9
bSpring Washer 9
cWasher 9
dNut 5
eAllen Key 1
fWrench 1
gScrew (2cm self-tapping) 3
Part List
Hardware

Noble House Home Furnishings LLC
Page 3 OF 9
hScrew (5cm self-tapping) 3
iRestraint Strap 2
jMetal Bracket 4
kScrewdriver (not
provided) 1
Before Beginning Assembly:
Assembly Steps
Assembly Preparation
Unpack and
place all parts
for clear
visibility.

Noble House Home Furnishings LLC
Page 4 OF 9
Step 1
Overview
Headboard(A)
Place the Headboard(A) on a clean, non-marring surface.
This Headboard has multiple parts and may require up to 30 minutes to
assemble. To give you an overview of the Headboard parts, the above picture
is to help you put the various parts into perspective. Please read through the
instructions below to familiarise yourself with the parts and steps before
assembly.
Headboard (A)
Left Support Leg (B)
Right Support Leg (C)

Noble House Home Furnishings LLC
Page 5 OF 9
Step 3
Put the Headboard(A) onto a flat table or panel.
Attach Left Support Leg(B) to Headboard(A) using Bolts(a), Washers(c) and
Spring Washers(b) with Allen Key(e).
Repeat the same process to install the Right Support Leg(C).
King size assembly - picture(1); Cal King size - picture(2)
At this point of assembly, DO NOT fully tighten the Bolts.
The final height of the Headboard may be adjusted to your own need.
Step 2

Noble House Home Furnishings LLC
Page 6 OF 9
Step 4
Heardboard Restraint Device Installation Instructions
Next, hold the Headboard upright and align to the Headboard bottom
mounting bracket to the Mattress Support Frame mounting bracket.
Attach Headboard to the Mattress Support Frame using Bolts(a), Washers(c),
Spring Washers(b) and Nuts(d) with Wrench(f).
Please install the Bolts from the FRONT TO BACK of the Headboard.
Make sure all parts are connected and securely locked into position.
Your Headboard is ready for use.
This Headboard can only be used on a flat, level surface.
WARNING
Serious or fatal crushing injuries can occur from tipping furniture. To help
prevent tip-over: ALWAYS secure this furniture to the wall using a Safety
Restraint Device. See product instructions for more ways to help prevent
furniture tip-over.

Noble House Home Furnishings LLC
Page 7 OF 9
Firstly, turn back the Headboard.
Find the two marks on the product.
Then, attach Metal Brackets(j) to the back of Headboard(A) using Screws(g)
with Screwdriver(k) as shown above.
Put the Headboard against the wall where desired and mark the location for
the Metal Brackets(j) to be the same height as the top of the Headboard.
Attach Metal Bracket(j) to the wall where you marked using Screws(h) with
Screwdriver(k).
Repeat this process with the other Metal Brackets(j).
Note: The Metal Brackets need to be secured to solid, load bearing
surface. Please use a Stud Finder(not supplied) if needed to locate the
Wall Frame.
Left support leg(B)
Right support leg(C)
g
j
Headboard(A)
h
j
h
jh
j

Noble House Home Furnishings LLC
Page 8 OF 9
Move the Headboard back against wall.
Pull the Restraint Straps(i) through the Metal Brackets(j) on the wall and
Headboard(A) one by one, and pull the Restraint Straps(i) tight.
Headbord Restraint Device is installed and Headbord is ready for use.
The strap between headboard(A) and Metal Brackets(
j
) on wall should be
within 3.5''.
i
j
j
g
h
Metal Brackets on
the back side of
Headboard
Metal
Brackets on
the wall
B
A
C
Within 3.5''

Noble House Home Furnishings LLC
Page 9 OF 9