Noble House Home Furnishings Barstool User manual

Assembly Instructions
Caution: You should read this carefully before you proceed
Barstool
Part List
Label Picture Description QTY
ABackrest
(with Legs) 1
BLeft Armrest
(with Leg) 1
CRight Armrest
(with Leg) 1
D Foot Rest 1
E Seat Panel 1
Hardware
Noble House Home Furnishings LLC Page 1 OF 8

Label Picture Description QTY
①Bolt (M6*20mm) 9
②Bolt (M6*40mm) 9
③Bolt (M6*65mm) 3
④ Washer 19
⑤Cap 11
⑥Allen Key 1
Assembly Preparation
Before
Beginning
Assembly:
Assembly Steps
Noble House Home Furnishings LLC Page 2 OF 8

Overview
This Barstool has multiple parts and may require up to 30 minutes to assemble. To give you an
overview of the Barstool parts, the above picture is provided to help you put the various parts into
perspective. Please read through the instructions below to familiarise yourself with the parts and
steps before assembly.
Step 1
Unpack and place all parts on a clean, non-marring surface.
FRONT FACING
Left Armrest (B) Right
Armrest(C)
Backrest (A)
Seat Panel (E)
Foot Rest (D)
Noble House Home Furnishings LLC Page 3 OF 8

Step 2
Place the Backrest(A) on the clean, non-marring surface.
Using the Allen Key(6), attach the Seat Panel(E) to the Backrest(A), with Bolts(2)
and Washers(4) as shown above.
Do not fully tighten the Bolts.
Step 3
Place the Right Armrest(C) on the clean, non-marring surface.
Using the Allen Key(6), attach the Seat Panel(E) to the Right Armrest(C) with Bolts(2) and
Washers( 4 ) as shown above.
Do not fully tighten the Bolts.
Noble House Home Furnishings LLC Page 4 OF 8

Step 4
Turn it over laying the Seat Panel(E) and the Backrest(A) on the clean, non-marring surface, with
the Right Armrest(C) facing upwards.
Again, using the Allen Key(6), attach the Right Armrest(C) to the Backrest(A) with Bolts(3) and
Washers(4), as shown above.
Do not fully tighten the Bolts.
Step 5
Place the Left Armrest(B) on the clean, non-marring surface, and set the stool over
of it, again with the Right armrest(C) facing upwards.
Attach the Left Armrest(B) to the Seat Panel(E) with Bolts(2) and Washers( 4 ),
using the Allen Key(6) as shown above.
Do not fully tighten the Bolts.
Noble House Home Furnishings LLC Page 5 OF 8

Step 6
Again, turn it over, placing the Right Armrest(C) on the clean, non-marring surface, with the Left
Armrest (B) now facing upwards.
Attach the Left Armrest(B) to the Backrest(A) with Bolts(3) and Washers( I4), using the Allen
Key(6) as shown above.
Do not fully tighten the Bolts.
Step 7
Turn the stool on its back by placing the Backrest(A) on the clean, non-marring surface.
Attach the Foot Rest(D) to the Backrest(A) with Bolts(1) and Washers( 4), using the Allen Key(6)
as shown above.
Do not fully tighten the Bolts.
Noble House Home Furnishings LLC Page 6 OF 8

Step 8
Place the Barstool on a LEVEL SURFACE to see if it wobbles.
If it wobbles, lift the Barstool some 30cm to 50cm from the ground.
Keep your feet and toes well away from the drop zone.
Drop the Barstool freely and vertically with the four legs hitting the ground at the same time.
This Drop Test will help to ensure that all the Bolts and gaps all reach full alignment status.
Test again for evenness on a LEVEL SURFACE.
If no wobbles are found, proceed to tighten all the Bolts.
When tightening the Bolts, tighten sequentially.
DO NOT tighten any Bolt fully and then move on to the next one.
This may cause the frame to warp.
If there are still wobbles, loosen the Bolts and execute the same drop test, then proceed to
tighten the bolts again in a sequential manner.
Step 9
Cover the Bolts with Caps(5).
Noble House Home Furnishings LLC Page 7 OF 8

Step 10
Your Barstool is ready for use.
This Barstool should only be used on a flat, level surface.
Right Armrest (C)
Left Armrest(B)
Noble House Home Furnishings LLC Page 8 OF 8