Noble House Home Furnishings Club Chair User manual

Label Picture Description QTY
A Seat Base 1
B Backrest 1
C Left Arm 1
D Right Arm 1
Assembly Instructions
Caution: You must read this before you proceed
CLUB CHAIR
Parts List
Noble house Home Furnishings LLC Page 1 OF 12

E Seat Cushion 1
F Back Cushion 1
G Left Arm Cushion 1
H Right Arm Cushion 1
I Front Seat Board 1
JWooden Leg with 1
Plastic Gasket 4
Hardwares List
Plastic Gasket 3
②Allen Wrench 1
Noble house Home Furnishings LLC Page 2 OF 12

Before
Begining
Assembly:
Assembly Preparation
Assembly Steps
FRONT FACING
Seat Cushion(E)
Back Cushion(F)
Wooden Leg with 1
Plastic Gasket(J)
Left Arm (C)
Front Seat Board(I)
Right Arm (D)
Left Arm Cushion (G) Right Arm Cushion(H)
Seat Base (A)
Backrest(B)
Noble house Home Furnishings LLC Page 3 OF 12

Step 1
Step 2
This Chair has multiple parts and may require about 30 minutes to assemble.
To give you an overview of the Chair parts, the above picture is to help you put the various
parts into perspective.
Please read through the instructions below to familiarise yourself with the parts and steps
before assembly.
Take the Seat Base(A), Backrest(B), Left Arm(C),Right Arm(D),Seat Cushion(E), Back
Cushion(F), Left Arm Cushion (G), Right Arm Cushion(H), Front Seat Board(I), and small
carton out from the large carton and place them on a clean, non-marring surface.
Open the Small Carton to take out the Wooden Legs with 1 Plastic Gasket(J), 3 additional
Plastic Gaskets(①) and the Allen Wrench(②).
Small Carton
J
Small Carton
①
B
C
E F
G
H
I
A
Noble house Home Furnishings LLC Page 4 OF 12

Carefully install the Legs with 1 Plastic Gasket(①) onto the bottom of the Left Arm(C) and
Right Arm(D). Insert the threaded stem into the mounting positions at the corner of the
Left Arm(C) and Right Arm(D). Tighten by turning the Legs clockwise.
Take notice of the shape of the Legs and ensure they are in the correct postions.
Note:The use of additional Plastic Gaskets are OPTIONAL and are especially useful to
help alleviate slight wobbleness. Some Legs may need more than one gasket while some
legs may not need any.
Step 3
CD
CD
Noble house Home Furnishings LLC Page 5 OF 12

With assistance from your adult partner, position the Left Arm (C) and Right Arm (D) as
shown in the picture. Hold up the Front Seat Board(I) and stand behind both Arms;
assemble the Front Seat Board(I) by placing the metal hooks onto the two raised screws
that are found on the hind side of both arms and tighten the screws using the Allen
Wrench(②). Tighten one by one and make sure they are fully into position.
Step 4
Left Arm(C)
Right
Arm(D)
Front Seat Board(I)
Noble house Home Furnishings LLC Page 6 OF 12

Step 5
With assistance from your adult partner, postion the Left Arm (E) and Right Arm (F) with
the Front Seat Board(G) as shown in the picture. Hold up the Backrest(B) and stand
behind both Arms. Align the mounting brackets on both sides of the Backrest(B) with
those on the hind side of the Left Arm (E) and Right Arm (F).
Then slide the Backrest(B) downwards to ensure it locks into place as pictured.
Backrest(B)
Left Arm(C)
Right
Arm(D)
Noble house Home Furnishings LLC Page 7 OF 12

With assistance from your adult partner, hold up the Seat Base(A) above the assembled
parts, and place the front side of Seat Base(A) towards the rail of the Front Seat Board(G)
as pictured.
Then slide the two downward hooks on each side of the Seat Base(A) into the upward
hook slots on the Left Arm (E), Right Arm (F), and Backrest (B). Ensure it is properly in
position.
Step 6
Seat Base(A)
Left Arm(C)
Backrest(B)
Right
Arm(D)
Noble house Home Furnishings LLC Page 8 OF 12

Place the Left Arm Cushion(G) against the Left Arm (C), positioning it onto the
magicTape.
Step 7
G
Magic Tape
A
C
B
DG
A
B
D
Noble house Home Furnishings LLC Page 9 OF 12

Step 8
Step 9
Place the seat cushion(E) on the seat Base(A) and in the right position.
Place the Right Arm Cushion(H) against the Right Arm(D), likewise positioning it onto the
magicTape.
H
E
Magic Tape
H
G
A
B
D
G
G
A
B
A
BH
GB
H
E
Noble house Home Furnishings LLC Page 10 OF 12

Step 10
Place the Back Cushion(F) against the Backrest(B) positioning it along the magic tape.
Ensure it is placed in its proper position.
Ensure all parts are connected and securely locked into position.
Your Chair is ready for use.
This Chair can only be used on a flat, level surface.
F
Magic Tape
F
G
H
E
G
H
E
Noble house Home Furnishings LLC Page 11 OF 12

Noble house Home Furnishings LLC Page 12 OF 12