Noble House Home Furnishings DINING CHAIR User manual

Label Picture Description QTY
A
Right Front Leg
(Labelled 'A')
1
B
Left Front Leg
(Labelled 'B')
1
C
Left Back Leg
(Labelled 'C')
1
D
Right Back Leg
(Labelled 'D')
1
E Backrest 1
F Seat 1
Assembly Instructions
Caution : You must read this before you proceed
DINING CHAIR
Part List
Noble House Home Furnishings LLC Page 1 of 6

Label Picture Description QTY
①Bolt (M6 x 50mm) 10
②Bolt (M6 x 40mm) 2
③Allen Key 1
Before
Beginning
Assembly:
Hardware
Assembly Preparation
Noble House Home Furnishings LLC Page 2 of 6

Step 1
This Dining Chair has multiple parts and may require up to 30 minutes to
assemble. To give you an overview of the Dining Chair parts, the above
picture is to help you put the various parts into perspective. Please read
through the instructions below to familiarise yourself with the parts and
steps before assembly.
Place Backrest(E) onto a clean table.
Align Seat(F) to Backrest(E) as shown above.
1.1) Attach Seat(F) to Backrest(E) using Bolts(①) with Allen Key(③) as
shown in the picture.
1.2) Attach Seat(F) to Backrest(E) using Bolts(②) with Allen Key(③) as
shown in the picture.
Do not fully tighten the Bolts.
Assembly Steps
Overview
Backrest(E)
Left Front Leg(B)
Seat(F)
Right Front Leg(A)
Right Back Leg(D)
Left Back Leg(C)
(1.1)
(1.2)
Noble House Home Furnishings LLC Page 3 of 6

Step 2
Step 3
Place the Seat Frame facedown on the edge of the table.
Insert Left Back Leg(C) and Right Back Leg(D) into the Seat(F) as shown.
Note: Make sure to match the Labelled mounting position with the
correct Legs.
Attach Left Back Leg(C) and Right Back Leg(D) to Seat(F) using Bolts(①)
with Allen Key(③).
Do not fully tighten the Bolts.
Noble House Home Furnishings LLC Page 4 of 6

Step 4
Step 5
Place the Dining Chair on a Level Surface to check if it wobbles.
Lift the Dining Chair some 30cm to 50cm high from the ground, keep your
feet and toes well away from the drop zone, and drop the dining chair freely
and vertically with the four legs, hitting the ground at the same time.
This Drop Test will help to ensure that all the Bolts and gaps reach full
alignment.
Test again for evenness on Level Surface.
If no wobbles are found, proceed to tighten all the Bolts.
When tightening the Bolts, tighten sequentially.
Do not tighten any Bolt fully and then move on towards the next one,
this could cause the frame to warp.
If it still wobbles, loosen the Bolts and execute this same drop test.
If the Dining Chair is not Stable it could lead to damage to the product.
Your Dining Chair is ready for use.
This Dining Chair can only be used on a flat, level surface.
Insert the Right Front Leg(A) and Left Front Leg(B) into the Seat(F) as
shown.
Note: Make sure to match the Labelled mounting position with the
correct Legs.
Attach Right Front Leg(A) and Left Front Leg(B) to Seat(F) using Bolts(①)
with Allen Key(③).
Do not fully tighten the Bolts.
①If wobble
③Test again
②
30
-
50mm
Noble House Home Furnishings LLC Page 5 of 6

Noble House Home Furnishings LLC Page 6 of 6