Noble House Home Furnishings 1352814460 User manual

Noble House Home Furnishings LLC Page 1

Caution:
Label
A
B
C
Assembly Instructions
●You must read this before you proceed.
SIDE TABLE
Parts List
QTY
Picture
Description
1
Drawer part
1
Leg
Leg
1
Noble House Home Furnishings LLC Page 2

D
E
Label
①
②
③
④
⑤
⑥
⑦
⑧
Leg
1
Leg
1
Hardware
QTY
Description
Picture
1
1
1
2
4
2
2
4
Screwdriver ( Not Provided)
Hammer (Not Provided)
Power Drill (Not Provided)
Bracket
Wall Plug Screw(M5x25mm)
Wall Plug (M5x35mm)
Tipover Restraint Strap
Knob ( Pre attached on the
inside of the Drawer)
Assembly Preparation
Before
Beginning
Assembly:
Noble House Home Furnishings LLC Page 3

Overview
This Side Table has multiple parts and may require up to some 30 minutes to
assemble. To give you an overview of the Side Table parts, the above picture
is to help you put the various parts into perspective. Please read through the
instructions below to familiarise yourself with the parts and steps before
assembly.
Assembly Steps
Step 1
Unpack and place all parts on a clean, non-marring surface.
Step 2
(B)
(A)
B
A
Noble House Home Furnishings LLC Page 4

Turn the Side Table right side up.
Place the Side Table on a LEVEL SURFACE.
Inspect the Side Table and make sure all the parts are adequately connected.
CAUTION 1: Tighten all the legs. If there is still wobble, tighten the legs
again. WARNING !! IF THE SIDE TABLE IS NOT STABLE ,IT COULD
LEAD TO DAMAGING THE PRODUCT.
Ensure all the legs are fully locked into position.
Step 5
Place Leg (E) to the Drawer part (A) as shown in Above Step 2 diagram.
Rotate the Legs in Anti-Clockwise direction.
Do not Thighten the Legs completely.
Step 3
Repeat the Step 2 to attach the remaining three Legs.
Do not Thighten the Legs completely.
Step 4
(B)
(C)
(D)
(A)
(E)
Noble House Home Furnishings LLC Page 5

Step 6
Tipover Restraint Device Installation Instructions
Usage For Tipover Restraint Device:
To secure Side Table against wall, attach two Brackets(④)on wall, use Tipover
Restraint Strap (⑦)to connect the Brackets (④).
Using Screwdriver (①) De-attach the Knob (⑧) from the inside of the
Drawer. Now attach the Knob (⑧) on the outisde of the Drawer as shown in
diagram.
6.1
Noble House Home Furnishings LLC Page 6

Attach Brackets (④)to Wall Plugs (⑥)using Wall Plug Screws (⑤)with the
help of aScrewdriver (①).
Step 8
6.1) Drill four holes on wall at same height as Brackets(④)on Side Table with
Power Drill (③).
You can mark these points in two ways as below:
1) Move the Side Table back to the wall. Mark two points same height as
Side Table on the wall.
Note: The Brackets need to be secured to solid, load bearing surface.
Please use aStud Finder(not supplied) if needed to locate the Wall
Frame.
2) Measure the height of the Brackets(④) with ruler/measuring tape and
mark on wall to keep them accurate and same height.
6.2) Insert Wall Plugs(⑥) into drilled holes on wall with Hammer (②).
Step 7
Noble House Home Furnishings LLC Page 7

Move Side Table to the wall.
Pull the Tipover Restraint Strap (⑦) through the Brackets (④) on the wall
and around the metal of the frame Side Table one by one, and pull the
Tipover Restraint Strap (⑦) tight.
This Side Table is now ready to use.
Caution: This Side Table can only be used on flat, LEVEL SURFACE
ONLY.
Noble House Home Furnishings LLC Page 8

●Dust and pick-up spills using a clean, non-colored,
lint-free cloth.
●Children should not climb or jump on the furniture.
●Stains may be removed with mild soap solution and
damp cloth.
●Not for commercial use. For residential use only.
●Do not place furniture outside . For indoor use only.
●Do not put hot items directly on furniture surface.
●Do not clean furniture with harsh cleansers or polish.
●Do not place furniture under direct sunlight.
●Do not write on furniture without a padded barrier to
protect the surface.
●Do not place furniture near heating or cooling vents.
Care & Maintenance
●Furniture may scratch floors. We recommend using
furniture pads to protect your floors.
Noble House Home Furnishings LLC Page 9