Noble House Home Furnishings LOVESEAT User manual

Assembly Instructions
Caution: You must read this before you proceed
LOVESEAT
CAUTION: This Loveseat is NOT a TOY.
Keep your child / children at bay during the assembly process of assembly.
For turning the Loveseat and to prevent damage to the Loveseat, 02 persons may be
needed to execute this action
Noble House Home Furnishings LLC 1

Label Picture Description QTY
A Backrest panel 1
B Seat Panel 1
C
Right Leg Panel
(with Leveler)
1
D
Left Leg Panel (with
Leveler)
1
E Leg Support Bar 1
Parts List
Noble House Home Furnishings LLC 2

Label Picture Description QTY
①Bolt
(M8x55mm) 7
②Bolt
(M8x25mm) 5
③
Screw
(M7x60 mm)
3
④
Flat Washer
(M8/18x1.5mm)
5
⑤Allen Key 2
Hardware
Assembly Preparation
Before Beginning Assembly:
Noble House Home Furnishings LLC 3

This Loveseat has multiple parts and may require up to 30 minutes to assemble. To
give you an overview of the Loveseat parts, the above picture is to help you put the
various parts into perspective. Please read through the instructions below to
familiarise yourself with the parts and steps before assembly.
Unpack and place all parts on a clean, non-marring surface.
Step 1
Overview
Assembly Steps
Seat Panel
(B)
Leg Support Bar
(E)
Backrest Panel
(A)
FRONT FACING
Right Leg Panel
(C)
Left Leg Panel
(D)
Noble House Home Furnishings LLC 4

Step 3
Position housing of Left Leg Panel (D) into pre-fixed iron dowel on Seat Panel (B) as
picture above.
Step 3.1: Secure Left Leg Panel (D) to Seat Panel (B) by using Bolt (①) with Allen
Key (⑤)
Step 3.2: Secure Left Leg Panel (D) to Backrest Panel (A) by using Bolt (①) with
Allen Key (⑤)
Do not fully tighten the Bolts.
Lay down Backrest Panel (A) then attach Seat Panel (B) to Backrest Panel (A) by
using Bolts (②), Flat Washer (④) and secure by Allen key (⑤).
Do not fully tighten the Botls.
Step 2
A
B
Step 3.1
Iron Dowel
5
D
A
B
Step 3.2
Noble House Home Furnishings LLC 5

Step 4
With assistance from your adult partners, turn the pre-assembled part in step 3 to the
other side.
Align the Tenon of Leg Support Bar(E) into the Mortise of Left Leg Panel(D). Then
position Mortise of Right Leg Panel(D) onto Tenon of Leg Support Bar(E) as shown
above.
Repeat same process in step 3.1 and 3.2 to Secure Right Leg Panel(C) to Seat Panel
(B) and Backrest Panel (A).
Do not fully tighten all the Bolts
Step 5
With assistance from your adult partners, turn the Chair back to normal flat ground.
Secure Left Leg Panel (D) to Leg Support Bar (E) by using Screw (③) with Allen Key
(⑤).
Repeat the same process to secure Right Leg Panel (C) to the remaining Leg
Support Bar (E).
Do not fully tighten the Screws.
5
E
C
D
D
C
E
A
B
Noble House Home Furnishings LLC 6

Step 7:
Your Chair is ready for use
Please use adjustable foot for uneven floors
This Chair can be used on a flat, level surface
Place the Chair on a LEVEL surface.
Inspect it and make sure all parts are adequately connected.
Gently and gracefully, sit onto the Chair.
This pressure will help to align all the parts at all joint areas.
Check for wobbles on a LEVEL surface.
If no wobbles are found proceed to tighten the Bolts and Screws in a sequential
manner, until evenly secured.
When tightening the Bolts and Screws tighten sequentially.
Adjust the Levellers until the Chair is level with the ground.
To adjust the Levellers, get assistance from an adult partner to lift/lean and
hold the Chair while you are working.
Step 6:
Adjust Pre-installed Levellers height for balance
Noble House Home Furnishings LLC 7

Noble House Home Furnishings LLC 8