Noble House Home Furnishings Chair User manual

Assembly Instructions
CAUTION: You must read this Assembly Instructions before you proceed.
Chair
CAUTION: This Chair is NOT a TOY.
Keep your child / children at bay during the assembly process.
Whenever lifting or moving the Chair and to prevent any damage to it, two adults may be needed to
execute these actions.
Please look in the Seat Panel for hardware packs.
Noble House Home Furnishings LLC PAGE 1 of 6

Label Picture Description QTY
A Seat Panel 1
B Backrest Panel 1
C Right Leg Panel 1
D Left Leg Panel 1
E First Support Bar 1
F Second Support Bar 1
Label Picture Description QTY
①Bolt
(M6x60mm) 9
②Screw
(M6x50mm) 5
③Allen Wrench 1
Part List
Assembly Preparation
Hardware
Before Beginning Assembly:
X9
X5
X1
Noble House Home Furnishings LLC PAGE 2 of 6

This Chair has multiple parts and may require up to 40 minutes to assemble. To give you an overview of the Chair parts,
the above picture is provided to help you put the various parts into perspective. Please read through the instructions
below to familiarise yourself with the parts and steps before assembly.
Place the Right Leg Panel (C) as shown in the picture above, onto a clean, soft surface to avoid any scratches or damage
to the product.
Step 2.1: With assistance from your adult partner(s), attach the Seat Panel (A) to the Right Leg Panel (C) using Bolts (①)
and the Allen Wrench (③) as the pictures show above.
Step 2.2: Then attach the Backrest Panel (B) to the Right Leg Panel (C) using Bolts (①) and the Allen Wrench (③) as
the pictures show above.
Do not fully tighten the Bolts at this time.
Unpack and place all parts on a clean, non-marring surface.
Step 1
Step 2
Overview
Assembly Steps
FRONT FACING
Backrest Panel (B)
Left Leg Panel (D)
Seat Panel (A)
Right Leg Panel (C)
First Support Bar (E)
2.1
2.2
Second Support Bar (F)
A B
C
1
1
3
3
Noble House Home Furnishings LLC PAGE 3 of 6

Step 3
With assistance from your adult partner(s), rotate the chair from front to back, attach the First Support Bar (E), then the
Second Support Bar (F) to the Right Leg Panel (C) using the Screws (②) and the Allen Wrench (③) as the pictures show
above.
Do not fully tighten the Screws at this time.
Place the Left Leg Panel (D) as shown in the picture above onto a clean, soft surface to avoid any scratches or damage to
the product.
Step 4.1: With assistance from your adult partner(s), attach the Seat Panel (A) to the Left Leg Panel (D) using Bolts (①)
and the Allen Wrench (③) as the pictures show above.
Step 4.2: Then attach the Backrest Panel (B) to the Left Leg Panel (D) using Bolts (①) and the Allen Wrench (③) as the
pictures show above.
Do not fully tighten the Bolts at this time.
Step 4
D
B
A
E
F
C
3
2
3
3
1
1
4.2
4.1
Noble House Home Furnishings LLC PAGE 4 of 6

Step 6
Turn the Chair right side up.
With assistance from your adult partner, adjust the Levelers to the desired height to avoid wobbles.
Inspect the Chair and make sure all parts are adequately connected.
In a sequential manner, tighten all Screws and Bolts at all joints.
CAUTION : When tightening these screws and bolts, tighten sequentially.
DO NOT tighten any screw or bolt fully and then move towards the next one. This could cause the frame to warp.
WARNING!! IF THE CHAIR IS NOT STABLE , IT COULD LEAD TO DAMAGE OF THE PRODUCT.
Your Chair is ready to be used.
This Chair can only be used on a flat, level surface.
Step 5
With assistance from your adult partner(s), rotate the chair from back to front, attach the First Support Bar (E), then the
Second Support Bar (F) to the Left Leg Panel (D) using the Screws (②) and the Allen Wrench (③) as the pictures show
above.
Do not fully tighten the Screws at this time.
F
E
D 2
3
Adjust Pre-installed Levelers
height for balance
Adjust high for balance Adjust low for balance
Noble House Home Furnishings LLC PAGE 5 of 6

Noble House Home Furnishings LLC PAGE 6 of 6