Norac UC5 Topcon X30 User manual

J
ohn Deere GS2 2600, 1800 and GS3 2630
JD 4630 Display Kit
Installation Manual
GS2-SP02

Printed in Canada
Copyright 2010 by NORAC Systems International Inc.
Reorder P/N: 54VT-GS2-SP02-INST Rev D (John Deere GS2 2600, 1800 and GS3 2630 JD
4630 Display Kit)
NOTICE: NORAC Systems International Inc. reserves the right to improve products and their specifications without notice and
without the requirement to update products sold previously. Every effort has been made to ensure the accuracy of the information
contained in this manual. The technical information in this manual was reviewed at the time of approval for publication.

1
Contents
1INTRODUCTION .............................................................................................2
1.1List of Parts................................................................................................................................................................. 2
2TECHNICAL SPECIFICATIONS ....................................................................3
3INSTALLATION ...............................................................................................4
3.1CANbus Interface Installation................................................................................................................................. 4
3.2Switch Box Installation ............................................................................................................................................. 5
4CABLE DRAWINGS.........................................................................................6
4.1Item C25: 44602-01 – Switch Remote Hand Control ..................................................................................... 6
4.2Item C26: 43240-26 – Cable UC5 Switch Box.................................................................................................. 7
4.3Item C40: 43260-08 – Cable UC5 CANbus 4 Pin DT..................................................................................... 8
4.4Item C41: 43210-01 - Cable UC5 Network 18 AWG - 1M............................................................................ 9

2
1Introduction
The John Deere GS2 2600, 1800 and GS3 2630 Display Kit Manual is intended to be used in
conjunction with the UC5 Spray Height Control Installation Manual. This manual provides
instructions to interface the UC5 Control Module to the John Deere GS2 2600, 1800 and GS3
2630 Display. For installation of the rest of the UC5 Spray Height Control System please refer
to the sprayer specific manual provided with the kit.
1.1 List of Parts
Item Part Number Name Quantity
C25 44602-01 BOX SWITCH UC4 REMOTE HAND CONTROL VER.1 RMR 1
C26 43240-26 CABLE UC5 SWITCH BOX 1
C40 43260-08 CABLE UC5 INTERFACE CAN BUS 4 PIN DT 1
C41 43210-01 CABLE UC5 NETWORK 18 AWG 1M 1
E12 43764 UC5 NETWORK COUPLER 2-WAY 1
M01 UC5-BC-MANUAL-ECHO-VT MANUAL UC5 OPERATORS - ECHO/VT 1
M04 54VT-GS2-SP02-INST MANUAL UC5 DISPLAY KIT JOHN DEERE GS2 2600, 1800 and GS3 2630 (JD 4630) 1

3
2Technical Specifications
CAN ICES-3(A)/NMB-3(A)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at their
own expense.
This Class A digital apparatus complies with Canadian ICES-003.
Pursuant to EMC Directive – Article 9, this product is not intended for residential use.
Table 1: System Specifications
Supply Voltage (rated) 12VDC
Supply Current (rated) 5A
Hydraulic Pressure (maximum) 3300 psi
Baud Rate 250 kbps
Clock Frequency (maximum) 96 MHz
Solenoid Valve PWM Frequency 300 Hz
Ultrasonic Sensor Transmit Frequency 50 kHz
Operating Temperature Range 0°C to 80°C

4
3Installation
3.1 CANbus Interface Installation
1. Securely mount the control module (E01) inside the sprayer cab.
2. Tee the CANbus interface cable (C40) in to the John Deere CANbus. The John Deere
CANbus connection can be found in the right hand armrest. The connector is a 4 pin
Deutsch plug labeled “CAN 2”.
3. Connect the 6 pin Deutsch plug on cable C40 to the 2-way coupler (E12). Connect cable
C41 between the 2-way coupler (E12) and the end of the control module with only one
Deutsch connector. C41 and E12 may not be required.
Figure 1: CANbus Interface Installation

5
3.2 Switch Box Installation
1. This step of the installation assumes that the input module and all required cables are
installed.
2. Disconnect cable C20 (Thru 2 connector) from the Input Module (E03). Remove the wedge
from the face of the 12 pin Deutsch plug. The wedge is removed by inserting a small flat
implement underneath the wedge and lifting it up.
3. Insert the Roll CW pin from C26 into position 3 of the 12 pin plug on C20. Insert the Roll
CCW pin from C26 into position 4 of the 12 pin plug on C20. Insert the wedge back into
the plug. Connect C20 to the Thru 2 connector on the Input Module.
4. Connect the 12 pin Deutsch plug on C26 to the OEM 3 connector on the input module.
Route the other end of the cable to the hitch of the sprayer (pull type) or to the cab (self
propelled).
5. Attach the switch box (C25) inside the cab and connect it to cable C26. An extra label is
provided with the switch box if you prefer to remove the switches from the housing and
mount them in the existing sprayer switch panel.
* Some sprayer types may not use all the switch functions.
Figure 2: Switch Box Installation

6
4Cable Drawings
4.1 Item C25: 44602-01 – Switch Remote Hand Control

7
4.2 Item C26: 43240-26 – Cable UC5 Switch Box

8
4.3 Item C40: 43260-08 – Cable UC5 CANbus 4 Pin DT

9
4.4 Item C41: 43210-01 - Cable UC5 Network 18 AWG - 1M

Canada
NORAC Systems International Inc.
Phone: [phone]
Toll Free: 1 800 667 3921
Shipping Address:
3702 Kinnear Place
Saskatoon, SK
S7P 0A6
United States
NORAC, Inc.
Phone: [phone]
Toll Free: 1 866 306 6722
Shipping Address:
6667 West Old Shakopee Road, Suite 111
Bloomington, MN
55438
Europe
NORAC Europe
Phone: (+33) (0)4 26 47 04 42
Shipping Address:
Rue de l’hermitage
01090 GUEREINS
France
www.norac.ca