Nordson AN-8 Plus User manual

OBSOLETE
Instruction Sheet
E1997 Nordson Corporation
All rights reserved 237 384A
Issued 4/97 Manual 10-30
P/N 237 384A
Iso-FlorHD and AN-8 Plus Gun Dolly System
Assembly
WARNING: Allow only qualified personnel to perform the
following tasks. Follow the safety instructions in this document
and all other related documentation.
This system consists of the following parts:
SManual Iso-Flo HD Voltage Block assembly
SAN-8 Plus gun with hoses
Selectrostatic power supply
Selectrostatic cable
Sdolly
Sattaching hardware
See Figure 1 and refer to the parts list to assemble the system onto the
dolly.
WARNING: To prevent injury to personnel and damage to
equipment, read and understand each manual included with
this system.
1.Make sure that the electrostatic voltage is off.
2.Open the Iso-Flo door.
3.Supply water through the fluid inlet. Check for leaks.
4.Turn on the compressed air to the Iso-Flo system. Verify that the
setting is 5–7 bar (80–100 psi).
5.Turn on the fluid inlet pressure. Verify that the setting is 5–10.3 bar
(80–150 psi).
6.Trigger the gun until water comes out.
1. Introduction
2. Assembly
3. Initial Startup

OBSOLETE
2
Gun Dolly System Assembly
1997 Nordson Corporation
All rights reserved
237 384A
Issued 4/97
Manual 10-30
CAUTION: Failure to clean up spills and repair leaks may
cause the system to ground out.
7.Check for leaks in the system. Clean up all fluid spills and repair
leaks.
8.Close the Iso-Flo door.
9.Turn on the electrostatic power supply. Verify that the voltage setting
is 60 kV or less.
10.Make sure that there is at least 2 bar (30 psi) of atomizing air to
activate the electrostatics.
11.Make sure that the microamp draw on the electrostatic power supply
is less than 100 ma.
12.Fill the system with coating material. Refer to
Changing the Coating
Material or Cleaning the System
in the Manual Iso-Flo HD Voltage
Block System Operator’s Card
.
See Figure 1.
Item Part Description Quantity Note
ÁÁÁÁÁ
ÁÁÁÁÁ
—
ÁÁÁÁÁ
ÁÁÁÁÁ
172 770
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
System, Iso-Flo HD, dolly mtd, with AN-8 Plus manual
gun
ÁÁÁÁÁ
ÁÁÁÁÁ
1
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
Á
ÁÁÁ
Á
ÁÁÁÁÁ
1
ÁÁÁÁÁ
Á
ÁÁÁ
Á
ÁÁÁÁÁ
172 785
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Dolly, 2 wheel, for dolly mount Iso-Flo, assembly
ÁÁÁÁÁ
Á
ÁÁÁ
Á
ÁÁÁÁÁ
1
ÁÁÁÁÁ
Á
ÁÁÁ
Á
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
2
ÁÁÁÁÁ
ÁÁÁÁÁ
983 140
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Washer, lock, 1/4in.
ÁÁÁÁÁ
ÁÁÁÁÁ
4
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
3
ÁÁÁÁÁ
ÁÁÁÁÁ
981 239
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Screw, hex head cap, 1/4-20 x 1/2in.
ÁÁÁÁÁ
ÁÁÁÁÁ
4
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
4
ÁÁÁÁÁ
ÁÁÁÁÁ
981 312
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Screw, hex head cap, 5/18-18 x 11/8in.
ÁÁÁÁÁ
ÁÁÁÁÁ
4
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
5
ÁÁÁÁÁ
ÁÁÁÁÁ
983 051
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Washer, flat, 5/16 in.
ÁÁÁÁÁ
ÁÁÁÁÁ
4
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
Á
ÁÁÁ
Á
ÁÁÁÁÁ
6
ÁÁÁÁÁ
Á
ÁÁÁ
Á
ÁÁÁÁÁ
225 579
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Iso-Flo, HD
ÁÁÁÁÁ
Á
ÁÁÁ
Á
ÁÁÁÁÁ
1
ÁÁÁÁÁ
Á
ÁÁÁ
Á
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
7
ÁÁÁÁÁ
ÁÁÁÁÁ
295 069
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Power unit, EPU-8
ÁÁÁÁÁ
ÁÁÁÁÁ
1
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
8
ÁÁÁÁÁ
ÁÁÁÁÁ
983 150
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Washer, lock, 5/16 in.
ÁÁÁÁÁ
ÁÁÁÁÁ
4
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
9
ÁÁÁÁÁ
ÁÁÁÁÁ
984 140
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Nut, hex, 5/16-18
ÁÁÁÁÁ
ÁÁÁÁÁ
4
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
10
ÁÁÁÁÁ
ÁÁÁÁÁ
111 048
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Gun, AN-8 Plus
ÁÁÁÁÁ
ÁÁÁÁÁ
1
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
11
ÁÁÁÁÁ
ÁÁÁÁÁ
247 351
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Hose, air
ÁÁÁÁÁ
ÁÁÁÁÁ
1
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
Á
ÁÁÁ
Á
ÁÁÁÁÁ
12
ÁÁÁÁÁ
Á
ÁÁÁ
Á
ÁÁÁÁÁ
900 545
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Á
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Hose, fluid
ÁÁÁÁÁ
Á
ÁÁÁ
Á
ÁÁÁÁÁ
1
ÁÁÁÁÁ
Á
ÁÁÁ
Á
ÁÁÁÁÁ
ÁÁÁÁÁ
ÁÁÁÁÁ
13
ÁÁÁÁÁ
ÁÁÁÁÁ
233 966
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ
Cable, HD, electrostatic, 60 in.
ÁÁÁÁÁ
ÁÁÁÁÁ
1
ÁÁÁÁÁ
ÁÁÁÁÁ
3. Initial Startup (contd.)
4. Parts

OBSOLETE
3
Gun Dolly System Assembly
1997 Nordson Corporation
All rights reserved 237 384A
Issued 4/97 Manual 10-30
1030001A
To Power Unit
To Cable Inlet on
Iso-Flo Cabinet
1
23
23
23
3
2
4
5
4
5
6
8
9
8
9
9
8
54
98
4
5
Connect Fluid Hose to
Regulator Outlet
10
11
12
13
7
Fig. 1 Assembly
4. Parts (contd.)

OBSOLETE
4
Gun Dolly System Assembly
1997 Nordson Corporation
All rights reserved
237 384A
Issued 4/97
Manual 10-30
For technical service within the United States, call Nordson Technical
Service at 1-800-275-6357. For assistance outside the United States,
call your local Nordson representative.
Iso-Flo, Nordson and the Nordson logo are registered trademarks of Nordson Corporation.
5. Nordson Technical
Service Help